FIRST MODEL MORSE CARBINE. SN 44. Cal. 50. This gun appears orig in every regard and is the most popular of the Morse models, having a solid brass latch. Mr. Michel, in his notes, describes this gun as follows: “Production of inventor George W. Morse’s patent carbines at the State Military Works in Greenville, South Carolina, resulted in the delivery of about 1,000 such carbines. This example of what is considered to be the first model (prototype models excepted) is serial number 44. It is distinguished by the latching mechanism which depends on an iron rod in the operating lever to both lock the action and, when driven forward by the hammer, to cause a movable firing pin to strike the primer on the base of the metallic cartridge”. CONDITION: Bbl is gray/brown, cleaned showing scratching and pitting. Brass frame, nose cap, and buttplate show numerous scratches and dings. There are some porous areas due to casting. Buttstock shows traces of orig varnish. Forestock exhibits most of hits varnish. There is a 1″ x 1-1/2″ repair to forestock adjacent to nose cap. Buttstock has several chips at frame. There is a gap between part of frame and buttstock. Cryptic letter stamped on buttstock at trigger guard is present but not discernible. Buttplate is missing jag. 4-31338 JS114 (20,000-25,000)

SECOND MODEL MORSE CARBINE. SN 308. Cal. 50. This is the scarcest of the Morse carbines with only about 100-150 made. Mr. Michel describes this gun as follows: “The Second Model (or Type II) Morse carbine, produced at the State Military Works in Greenville, South Carolina, is distinguished by a more sophisticated locking and firing mechanism. Included in this improved mechanism is the presence of a flanged iron rod connected to an iron plate with knurled edges which covers the forward top portion of the brass operating lever. The serial number range for this type of carbine is from 200 to the near 350 range. This carbine is serial numbered 308. Legibly scratched on the right side of the frame is ‘Captured at Columbia, South Car’… ex-Lee A. Petrov collection”. Rarely do we find Confederate carbines with capture information scratched so nicely, telling us a piece of their history. CONDITION: Brass surfaces are scratched and cleaned with numerous small dings and stains. Capture information scratched in frame is quite legible. Buttstock retains much of its orig varnish. Cryptic letter “C” in buttstock is well struck and discernible. Forestock is possible restoration, as is ramrod. Bbl lacks ramrod catch. Nose cap appears orig. Forestock exhibits raised grain and is very good. 4-31339 JS115 (20,000-25,000)

THIRD MODEL MORSE CARBINE. SN 743. Cal. 50. This is a good example of the standard production Morse carbine. Most production Morses were in this final model. Mr. Michel, in his notes, describes this gun as follows: “The Type III carbine, also manufactured at the State Military Works in Greenville, SC, retains the flanged rod device, but now the sliding breechblock is made of iron. Type III carbines are in the 350 serial number range until the end of production”. CONDITION: Brass frame, nose cap, and buttplate have pleasant patination over scattered nicks, gouges, and scratches, especially nicked around latch, where someone did not know to cock gun to open. Bbl is brown and smooth with scattered pitting, especially at muzzle. Forestock appears to be made of tiger maple and is possibly restored. 4-31340 JS116 (15,000-20,000)

CONFEDERATE TARPLEY CARBINE. SN 24. Cal. 52. This gun has an overall length of 39-1/2”. Bbl is 23” long and has 7 lands and grooves, which conforms to other known examples. Frame is brass, having a distinctive red tint, indicating the high copper content that is so characteristic to many Confederate manufactured arms. Frame tang is marked in 3 lines “J. H. TARPLEY’S / PAT. FEB. 14. / 1863”. Iron breechblock is hinged to the frame, being retained by a flat latch spring. Jeremiah Tarpley received a Confederate patent for his own design early in 1863. The state of North Carolina had an order for 200 guns between April and September of 1863. About half of Tarpleys produced and delivered to the state of North Carolina were rejected. The survival of these guns is rare—only 20 guns, of which less than half are in private hands. Eleven guns are in institutions, one being in the Army Museum in Madrid, Spain. Of the known 20 guns, 19 have an integral projecting step to help the latch spring hold breechblock in place; however, this gun, SN 24, being the lowest SN known, lacks this integral step. This is the only surviving specimen without this extra device to help maintain the breech closure. This gun is illustrated in Murphy & Madaus’ monumental work, Confederate Carbines and Musketoons. This carbine is among the finest Tarpley carbines known and appears orig and authentic in all regards. Since there are only two minor variations in Tarpleys, one lacking the projecting step for the spring latch, and the other with the projecting step, if you want a complete collection of Tarpleys of both types, this is your only chance to own both, as this is the only known low serial numbered Tarpley which has this feature. There is a battlefield excavated frame only of SN 16 with this same feature, but it is frame only. This is undoubtedly the finest Tarpley carbine to ever be offered at public auction, and since it’s one of the top few, it is probably the finest Tarpley that will ever be sold. Mr. Michel’s Notes State: “Jeremiah H. Tarpley, after a brief enlistment in the North Carolina “Guilford Grays,” received a patent for his breechloading system on February 14, 1863. He joined the firm of J & F Garrett Company, a Greensboro, North Carolina foundry. The State of North Carolina was the first major purchaser of a carbine using his system, and thereafter, Tarpley, Garrett & Co. offered these arms for public sale in newspaper advertisements and in broadsides. This example, serial number 24, is one of the lowest serial numbers known. In overall excellent condition, it represents one of the rarest of all Confederate carbines. Provenance: Illustrated and described and ”Confederate Carbines and Musketoons” by John Murphy and Howard Madaus, p. 216.” CONDITION: Iron surfaces are gray/brown with scattered pitting. Brass surfaces have good patina. Bore is very good. Stock is very good with scattered nicks and scratches. There are 2 repaired chips to stock where frame tang and frame come together. Latch and trigger guard are professionally restored. 4-313454-31469 JS243 (75,000-125,000)

KEEN WALKER CARBINE. SN NSN. Cal. 54. Mr. Michel, in his notes, states, “The Keen, Walker & Co. carbine, long known as the Confederate ‘Perry’ or ‘Tilting Breech’ carbine and the subject of much speculation as to where it was manufactured, has now been identified as the product of Keen, Walker & Co. in Danville, Virginia. The frame is of brass and unmarked except for Roman numerals on the internal parts. The 22-1/2″ bbl is rifled in caliber .54 and also unmarked except for an inspection of proofmark ‘P’ on the upper side of the barrel near the breech. This specimen has the initials ‘AH’ carved on the top of the comb near the stock”. This is a fine example that appears in near “attic”, untouched condition. It would be difficult to find a more pleasing specimen of this scarce Confederate carbine. Mr. Michel’s Notes State: “The Keen Walker & Co. carbine, long known as the Confederate “Perry” or “Tilting Breech” carbine and the subject of much speculation as to where it was manufactured, has now been identified as the product of Keen, Walker & Co. in Danville, Virginia. The frame is of brass and unmarked, except for Roman numerals on the internal parts. The 22½” barrel is rifled in caliber .54 and also unmarked except for an inspection or proof mark “P” on the upper side of the barrel near the breech. This specimen has the initials “AH” carved on top of the comb of the stock.” PROVENANCE: Ben Michel collection. CONDITION: Copper/brass frame has nice patina, as does the brass sideplate. Note the dissimilar patinas due to the dissimilar alloys. This is a distinctive characteristic of this particular maker. Bbl is smooth and brown with areas of scattered pitting. “P” proof on bbl is crisp and sharp. Rifling and bore is very good. Stock retains over half of its orig varnish. Traces of orig blue are found on trigger guard. Nipple is probably replaced. 4-31344 JS117 (20,000-25,000)

COLUMBUS ARMORY CARBINE. SN 18. Cal. 58. This Capt. F. C. Humphries inspected carbine was probably a product of the Columbus Armory, though the lock is unmarked. Several Confederate carbines made by various makers in Columbus, Georgia and the surrounding area have similar features. Among these makers are J. P. Murray, Columbus Armory, Dickson & Nelson, and David & Bozeman. All these manufacturers shared similarly designed carbines and Mississippi-style rifles. All these makers normally marked their guns, with exception of the Columbus Armory, where only 2 or 3 marked specimens are known. Based on this information, we believe this unmarked gun to be a product of the Columbus Armory. Earlier literature usually identifies these guns as J. P. Murray. Bbl of this gun is inspected “PRO./F.C.H.” which is seen on known J. P. Murray and Columbus Armory weapons. Information on the Columbus Armory only recently has come to light in the marvelous book by John Murphy and Howard Madaus, Confederate Carbines and Musketoons. Murphy and Madaus, in their book, describe a letter from John D. Gray, of the Columbus Armory, describing his contract for 1,000 carbines. This carbine is like a J. P. Murray Type II carbine where the two known marked Columbus Armory are like the J. P. Murray Type I carbines. The difference between the Type I and Type II carbines is the double strap front band as opposed to 2 bands and a nosecap like the gun being offered here. Lock screws and tang screw are also serial numbered “18”. This gun is serial numbered “18” on hammer and inner surface of lockplate, consistent with the three known Columbus Armory marked locks. Bbl is marked “PRO./F.C.H.” consistent with the other Columbus Armory products. There is no number on bottom of bbl; however, there is a group of 3 dots. This bbl is also marked “ALA / 1864” which is not seen on either of the known Columbus Armory guns. Gun is complete and authentic, lacking only its rear sight. Mr. Michel’s Notes State: “The rifles and carbines produced by the partnership of Eldridge S. Greenwood and William C. Grey at Columbus, Georgia, share the same basic configuration, differing only in the barrel length. Manufactured under the apparently watchful eye of John P. Murray, superintendent and master armorer of the Greenwood and Grey facility, these weapons show a consistently high grade of workmanship. The barrel of the carbine is 23½ inches, marked “PRO” and “FCH” and held by two bands of the same type as the rifle. The stock ends in a brass nosecap. The lockplate of this carbine is unmarked, which is not unusual.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are all brown with scattered pittings. Bbl markings are deep and discernible. Inspector’s mark “FCH” is only visible when bbl is removed. Brass bands, nosecap, trigger guard, and buttplate are all cleaned and smooth. Stock is sound and solid with a visible repair around breech tang and behind lockplate. 4-31335 JS136 (10,000-15,000)

BILHARZ, HALL & CO MUZZLELOADING CARBINE. SN Not found. Cal. 58. This gun is a copy of the US Model 1855 rifle/carbine. These carbines typically come with pewter nosecaps, and earlier SN guns with brass nosecaps, such as this one. There is no SN on this gun on back of bbl breech where SN is typically found; however, the typical cryptic assembly markings are found internally on lock and bottom of bbl “C81”. Large Roman numeral “VXX” is cut on bottom of bbl and in stock channel. Other small assembly numbers occur on various lock parts and hammer. This is a nice example of the less frequently encountered, brass nosecapped carbine, made at Pittsylvania Courthouse, Va. Mr. Michel’s Notes State: “Bilharz, Hall carbines with the brass nosecaps are believed to be the production of muzzle loading carbines made following production of the breechloading “rising breech” carbines. Long mistakenly referred to as D. C. Hodgkins carbines, these carbines resemble the U. S. Model 1855 Springfield rifled carbine. The barrel is marked with a “P” and “CSA”. The serial number is on the left rear surface of the breech.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is gray/brown with areas of scattered pitting. “CSA” surcharge is stamped on left flat of bbl breech and is only fully discernible when bbl is removed. Rifling in bore is very good, though pitted. Lock, buttplate, and trigger guard have smooth, brown surfaces with scattered pitting. Stock is sound with hairline crack, approx. 1″ long, opposite lock and an old repair is visible to wood behind lock adjacent to breech tang. 4-31336 JS135 (15,000-20,000)

BILHARZ, HALL & CO MUZZLELOADING CARBINE. SN 451. This carbine is listed in Murphy & Madaus’ book Confederate Carbines and Musketoons. Surviving examples of this carbine are generally well-used and worn. This is an especially nice example and appears all orig and complete. Patterned after Model 1855 US muzzleloading carbine. One of the few differences between the US and this model is that this gun used a fixed rear sight as opposed to an adjustable one. This gun exhibits typical assembly letters and numbers, the bbl having “A3” stamped on bottom. SN “451” is found on bbl breach. Lock, internally is also marked “A3” and “12 / 2”. Hammer and other internal lock parts have same numbers stamped on them. Mr. Michel, in his notes, provides the following information: “Following production of the breechloading ‘rising breech’ carbines, Bilharz, Hall & Co. of Pittsylvania Court House, Virginia, turned to developing a muzzleloading carbine. As ultimately produced, the carbine resembles the US Model 1855 Springfield rifled carbine with a 22″, .58 caliber barrel. The ramrod is held by a swivel as with the Model 1855. The lockplate is unmarked. The barrel is marked with ‘CSA’ atop the breech and a ‘P’ opposite the bolster. The serial number appears on the left rear surface of the breech of the barrel. These carbines with the pewter nosecaps are thought to be later production than those having brass nosecaps”. CONDITION: Bbl is gray with discernible “CSA / P” proof. Scattered nicks, dings and pitting. Rifling in bore is faint, but discernible and pitted. Other metal surfaces are gray and cleaned. Stock overall is very good with good edges and has scattered dings, gouges, cracks, and scratches but still retains some orig varnish. Pewter nosecap is uncleaned, showing good patina. 4-31337 JS131 (20,000-25,000)

EXCEEDINGLY RARE AND DESIRABLE CONFEDERATE RISING BREECH CARBINE (BILHARZ, HALL & COMPANY). SN 20. One of the great rarities in Confederate arms collecting and one of the most sought after long arms in the arms collecting field is this Rising Breech Carbine. Its origins have long been the subject of much controversy in the confederate arms collecting field being attributed to a number of Southern armories and manufacturers. Recent research and much study by well known arms scholar Howard Michael Madaus and reported in published works, has shown that this carbine, once attributed to D.C. Hodgkins, is actually the product of the Bilharz, Hall & Company of Pittsylvania Court House, Virginia. This firm also produced a muzzle loading percussion carbine. The identity of die stampings, rifling, and other manufacturing details associated with the muzzle loading carbine and the Rising Breech Carbine have led scholars to this attribution with little dispute. Courthouse records, summarized below, also confirm the attribution of this rare carbine to this Virginia firm. This carbine is in .54 caliber Serial Number 20, and fired a paper cartridge. The breechblock rises vertically when the trigger guard/lever is lowered. Iron mounted on a two-piece walnut stock, the round barrel measures 21” long and is secured by a single flat barrel band. There is a sling ring mounted on the left side of the stock. The serial number appears on the frame, breechblock, inside the lever and on the underside of the butt plate. “CS” is stamped on the breech of the barrel and on the breechblock and the proof mark “P” is found beneath the barrel as well. The front sight is a pinched blade style with a three leaf graduated rear sight. The Bilharz, Hall & Company gun factory was built in what was a tin shop/foundry on Main Street in the Town of Chatham, Pittsylvania County, Virginia. According to the deed, its location was in back of the Masonic Lodge Hall some 1400 feet north of the Courthouse on land the partnership purchased of George A. Carter. Candidus Bilharz was the principal in the firm. Bilharz was an immigrant from Baden, Germany who was naturalized in Pittsylvania County in 1859. He was a harness maker, vintner/distiller, miller and mechanic who lived near Tanyard Branch in Chatham. Bilharz was connected to the prominent Bolanz family which emigrated from Baden, Germany also. Bilharz’s partner George Hall was a prominent businessman who owned a small tin shop along with extensive land holdings in the county. Records show him acting in various official capacities on behalf of the county during the Civil War. Col. Coleman D. Bennet was a silent partner in the firm and was presumably its chief benefactor. Bennett was a man of enormous wealth who owned vast tracts of county land plus a whole block of buildings on Main Street in downtown Chatham. Records show that thirty-eight people were employed by the gun works, and those fit for military service were given Confederate draft deferments due to their profession. Some of the names of the employees were as follows: G.C. Haden, A.C. Haden, R.L. Haden, John H. Shelton, Nathaniel Shelton, C.L. Mott, James Motley, B. Riddle, J.D. Reynolds, B. Reynolds, J.T. Abbott, C.P. Oakes, John H. Brown, M.B. Dickson, William Brown, Frank Compton, R.W. Hall, J. Beaver, J.H.C. Hutcherson, and Benjamin Dyer. Ages of the workers ranged from 18 to 40. Job titles included the following: Stocker, Rifling Hand, Polisher, Vice Hand, Band Holder, Helper and Mechanic. The 400 or so firearms produced from August of 1862 through March of 1864 (when operations ceased) were manufactured under contract with the Confederate Ordinance Department. Records also show that the firm purchased thousands of pounds of “skelp iron” from the Confederate government for use in rifle barrels. Interestingly, the company also manufactured 1745 wooden stocks at a dollar each for other rifle factories. These carbines did not receive favorable reports from Confederate ordnance inspectors; nonetheless, they most certainly saw service in the arms strapped South. ONLY 100 of these Rising Breech Carbines are thought to have been produced with only a handful known examples in the collecting world. Here we have a superb opportunity to obtain one of the rarest of confederate long arms in excellent condition. CONDITION: Excellent. All metal surfaces have been lightly cleaned but now retain a light to medium grey patina. The stocks show light use and wear but are in superb condition with the expected nicks and dings here and there. Light pitting exists around the nipple on the breechblock; otherwise the metal surfaces are smooth. Mechanically excellent. 4-31343 CW15 (40,000-60,000)

S. C. ROBINSON CONFEDERATE SHARPS. SN 2468. Cal. 52. This fabulous, historic carbine, identified by inscription on the stock to a member of “Stuart’s Cavalry”. Also written on the side of the stock “MOBILE, ALABAMA”. Stuart’s Cavalry was one of the hardest fighting calvary units in the Civil War and Lee had come to rely so much on Stuart’s elite and fleet ability that his absence during the onset of the Battle of Gettysburg was a tremendous loss to Lee and in his mind, in part, resulted in the defeat at this monumental battle for the South. This is a nice, orig and complete example of the earliest made Confederate Sharps carbines. SN appears externally on lock and frame. Lock is marked “SC Robinson / Arms Manufactory / Richmond Va / 1862” and bbl is marked behind rear sight “Richmond Va / 1862”. Initials “LSK” are nicely carved in buttstock. A search of Confederate records reveals an L.S.King who enlisted 7/31/1862 as a Private in Co G Va 4th Cavalry of Jeb Stuart’s division. Mr. Michel, in his notes, offers the following information: “Manufacture of the Sharps pattern carbine by the S. C. Robinson Arms Manufactory from Dec. 1862 to March 1, 1863, when the carbine factory was taken over by the Confederate government. during this short period, close to 2,000 carbines were produced. While these carbines generally follow the outline of the actual Sharps, the difference is immediately noticeable as the lockplate is not drilled for the Lawrence primer feeder and the hammer is more narrow and not imbedded into the outer projection of the receiver. The lockplate is marked ‘S.C. Robinson / Arms Manufactory / Richmond Va / 1862’. The top surface of the barrel is stamped ‘S. C. Robinson / Arms Manufactory’, and behind the rear sight is stamped ‘Richmond Va / 1862’. The serial number appears at the tail of the lockplate. This is the highest serial number known for a Robinson-marked carbine”. You are bidding on a popular Confederate carbine that generally saw a lot of use, and though this gun was used in battle, it is generally well preserved and complete. CONDITION: Bbl is brown/gray with scattered pitting. Other metal surfaces are also brown/gray with scattered pitting. Rifling in bore is deep and distinct, though pitted. Brass band has been cleaned. Brass buttplate is smooth and exhibits nice patina. Buttstock exhibits some orig varnish with numerous small nicks, dings, and scratches. Forestock has 3″ hairline crack which does not affect aesthetics. 4-31342 JS132 (20,000-40,000)

CONFEDERATE SHARPS CARBINE. SN 2370. Cal. 52. This is an exceptionally nice Confederate Sharps with sharp edges and crisp markings. SN is found on frame, bbl, and lockplate. When forestock is removed to view SN, orig bright brown finish is visible in this protected area. Mr. Michel, in his notes, describes this gun as follows: “Sharps pattern carbines made after the takeover of S. C. Robinson’s carbine factory no longer carry the same markings found on the earlier production. The lockplates are stamped only with the serial number at the tail of the lockplate. The top of the barrel is stamped only ‘Richmond Va’ behind the rear sight”. You are bidding on one of the finest Confederate Sharps carbines to market in many years. It would be difficult to upgrade this particular example. CONDITION: Metal is cleaned with sharp edges. Bbl has several areas of pitting. Breech and frame are smooth. SNs are well stamped. Richmond markings are clear and well stamped. Rifling in bore is very good. Wood is very good, still exhibiting raised grain. Several small dents are present on both forestock and buttstock. There is a 2-3″ hairline crack near bottom of buttplate which does not affect aesthetics. 4-31341 JS118 (15,000-20,000)

SCARCE AND EARLY PRODUCTION CONFEDERATE COOK & BROTHER ATHENS GEORGIA PRODUCTION CAVALRY CARBINE INSCRIBED TO A VIRGINIA CAVLARYMAN. SN 2865. One of the great rarities in Confederate long arm collecting is this early production Cook & Brother cavalry carbine serial number 2865. Its stock inscription that reads “S.W. Ellyson/Co. F/3rd Va. Cav.” enhances this rare carbine with rich history. This example has all of the early features including the iron swivel ramrod and sling ring bar on the left side of the stock. This carbine is in .58 caliber with a 21 1/8” barrel, two barrel bands and brass furniture on a black walnut stock. The front sling swivel is of brass, the rear of iron with a sling ring bar mounted to the left side of the stock having a large brass ring. Pinched front sight and fixed rear sight. All markings are correct. The left barrel flat near the breech is marked “Proved”, “Cook & Brother/Athens 1863/ 2865” is stamped on the right side of the barrel between the rear sight and the breech. The lock plate is stamped “Cook & Brother/Athens GA. 2865” over the date “1863.” To the rear of the hammer is a depiction of the Confederate First National Flag. One the cheek side of the stock, this carbine is inscribed and identified to a trooper in the 3rd Virginia Cavalry. The National Archives in its “Compiled Service Records of Confederate Soldiers Who Served in Organizations From the State of Virginia” shows a Samuel W. Ellyson as a member of Captain Vaiden’s Company F, 3rd Regiment Virginia Cavalry in 1863. The 3rd Virginia Cavalry served in Stuarts’ Cavalry Division, Fitzhugh Lee’s Brigade during the Battles of Antietam and Gettysburg. This rare and desirable identified Confederate cavalry carbine represents a unique opportunity to acquire a real piece of American history associated with one the Confederacy’s most renowned and hard fought cavalry units. Mr. Michel’s Notes State: “The rarest of all Cook & Bro. productions of longarms is the carbine. The 21-1/8” barrel is well marked “Cook & Brother / Athens Ga 1863 / 2865”. The lockplate is marked, forward of the hammer “Cook & Bro”, “Athens”, and the date. All parts are serial numbered 2865. The stock is carved “S. W. Ellyson Co F 3rd Va Cav”. Ellyson mustered on August 29, 1862, as a Private in Capt. Vaiden’s Company of Cavalry, Company F, 3rd Regiment, Virginia Cavalry. Provenance: Charles M. Glenn, Jr. (who acquired it as a young boy in 1928 from a childhood friend in trade for an ice cream cone).” PROVENANCE: Ex. Coll Charles M Glenn, Jr. (who acquired it as a young boy in 1928 from a childhood friend in trade for an ice cream cone. CONDITION: Very good. All metal surfaces have aged to a nice grey patina; the walnut stock is in excellent shape with only a few areas with heavy wear. The inscription is clear and is of the period. The carbine functions mechanically well. 4-31292 CW14 (20,000-25,000)

COOK & BROTHER MUSKETOON. SN 2419. This 24″ bbl musketoon is often known as an artillery carbine. Lock is marked “Cook & Brother / Athens Ga / 1863” and SN “2419”. There is a Confederate First National Flag stamped rear of hammer on lockplate. Bbl is marked “Cook & Brother / Athens Ga / 1863” and SN “2511”, as is rear band and nose cap. Front band is SN “2509”. Since the SNs are mixed but all within 100 numbers or so, the gun was probably used in this configuration. Buttplate is stamped “CS”. “CS” surcharges on these guns are not normally encountered; however, this marking appears quite old and though it could have been done at any time, or even by a GAR post showing that their captured gun was Confederate, this mark adds to the aesthetics of the gun. Rear sling swivel is missing and has a screw placed contemporarily in its hole. Mr. Michel, in his notes, describes this gun as follows: “This musketoon, of the slimmer form in stock pattern probably represents a transition from New Orleans production to that of Athens, Ga. Although the lockplate is well marked as Athens production and dated 1863, it is serially numbered at 2419, about 100 numbers from the serial number which appears on the barrel, 2511. The brass front sight on the barrel is more characteristic of New Orleans production than Athens, as is the trigger guard, where the sling swivel is attached to a screw base rather than a lug on the trigger guard plate”. CONDITION: Bbl and lock are gray/brown with scattered staining, nicks, dings, and pitting, especially at breech. Brass rear sight, bands, nose cap, buttplate, and trigger guard are cleaned. Stock has several breaks and repairs, including piece of wood missing at toe. Repair at wrist, several repairs around lock. Ramrod is replaced and is pitted around tip. Both front and rear sights appear orig. Rifling in bore is sharp but pitted. Tang screw appears replaced. 4-31291 JS128 (12,000-18,000)

COOK & BROTHER MUSKETOON. SN 4920. Cal. 58. Cook & Brother 24″ bbl musketoon or artillery carbine, as the British gun was called, after which this gun was patterned. SN appears on lock, bbl, and nosecap. Lock is marked forward of hammer “Cook & Brother / Athens Ga / 1864 / 4920”. Bbl is similarly marked. Lock screws are also serial numbered “4920”. Tang screw is serial numbered “5428”, but appears orig to this gun. Opposite lock in stock is inspector’s cartouche “WH”. Wescom Hudgins was government inspector working in Athens in 1864. Mr. Michel, in his notes, states: “Cook & Brother produced musketoons with significantly different stock types. This is an example of the heavier, more bulky type, with the other being slimmer in form. Both types are 2-band brass mounted with 24″ bbls. Lockplate on this example is well marked, forward of the hammer, ‘Cook & Brother / Athens Ga / 1864’, as is the tang. At the tail is a depiction of the Confederate National Flag. All parts, nosecap, barrel bands, barrel, lockplate, trigger guard, and buttplate are serial numbered, in this case, ‘4920’…Ex. coll. George Knight”. CONDITION: Bbl is cleaned with scattered areas of staining and pitting. Rifling in bore is discernible though pitted. Bbl breech is well defined. Bbl markings are distinct. Lock is cleaned and pitted. All markings are discernible. Hammer is an Enfield replacement. Bbl bands are possible replacements. Ramrod is cleaned and pitted, matches condition of bbl, but is of Austrian manufacture. 4-31290 JS134 (15,000-20,000)

FAYETTEVILLE RIFLE. SN NSN. Cal. 58. This is the standard, late production Fayetteville rifle with 33″ bbl. This is a nice example, orig and complete. Lock is dated “1864”, as is bbl. Opposite lock is inspector’s cartouche which is still quite visible. Also, on back of stock is scratched “Captured April 1865”. In same style of markings as the capture information the gun is marked “TR 1866″ opposite lock. This gun has seen some use, but rifling is still decent. Gun is accompanied by a heavy, Confederate, canvas sling and an angular bayonet that fits gun well. This gun exhibits all proper proofs and markings normally associated with this maker. Mr. Michel describes this gun as follows: Manufactured on the rifle equipment removed from Harpers Ferry to Richmond and ultimately to Fayetteville, NC, this rifle is characteristic of production there. The hammer is of the distinctive ‘S’ curve configuration. The lockplate is marked, forward of the hammer, with an eagle over ‘CSA’ (the ‘S’ being upside down when the die was created) and ‘Fayetteville’ and with the date ‘1864’ at the tail. The date ‘1864’ also appears on the barrel at the breech. The left side of the buttstock is carved ‘Captured April 1865’. The rifle is complete with its correct socket bayonet and linen sling.” You are bidding on a very good, all orig and complete, 1864-dated Fayetteville rifle with orig sling and bayonet. CONDITION: Bbl, lock, and ramrod are cleaned and gray/bright with scattered areas of pitting. Brass buttplate, trigger guard, bands and nose cap are cleaned and smooth with scattered nicks and scratches. All markings in metal are crisp and bright and easily read. Stock exhibits scattered scratches, nicks, and scrapes. Cartouche is well defined, though worn. Hairline crack about 1″ long is found just behind lock. There is about a 2″ x 1/4″ wood sliver repaired behind hammer. Bayonet is gray with scattered staining and pitting. Sling is very good and solid. Leather strip is very good with no discernible cracking. Leather loop is scuffed in high areas. Sling overall is in superior condition from those normally encountered. 4-31306 JS124 (10,000-15,000)

RARE, EARLY AND FINE NEW ORLEANS PRODUCED CONFEDERATE COOK & BROTHER RIFLE. This example is, clearly, one of the earliest products of this notable Confederate arms manufacturer and one of the best surviving examples. Manufactured by this well known Confederate long gun manufacturer is this 1861 dated and New Orleans marked Cook & Brother rifle. Generally following the English Enfield style, this rifle is a .58 caliber percussion muzzleloader 2-band rifle with a 33” barrel having the distinctive “twist” in metal’s surface and having an attached lug for a sword bayonet. The barrel retains its original front sight and its long range rear sight. Lock, barrel and ramrod are of iron; all other furniture is of brass, including the sling swivels located at the top band and at the rear of the trigger guard. The barrel is marked “Proved” at the left breech and stamped “N.O. 1861” on the top of the barrel between with rear sight and the breech. The lock plate is marked “Cook & Brother, N.O. 1861” and has the distinctive Confederate 1st National flag stamped immediately before the hammer on the lock plate face. The stock is of walnut and the ramrod of the Enfield pattern with knurled and slotted head. The Cook and Brother firm was established in New Orleans at the outbreak of the Civil War. Threatened by the fall of that City early in the War, their manufacturing operation was moved to Athens, Georgia in 1862. Ferdinand W.C. and Francis L. Cook, recent English immigrants, were the principals in the firm. The former was a skilled engineer for the manufacture of Enfield rifles, bayonets and cavalry horse shoes. Said to be the largest and most efficient private armory in the Confederacy. It produced rifles, carbines and musketoons declared by an ordnance officer to be “superior to any that I have seen of Southern manufacture.” Under contract to supply 30,000 rifles to the Confederate Army the armory operated until its employees, organized as a reserve battalion under Major Ferdinand and Captain Francis Cook, were in 1864 called to active duty upon the approach of Sherman’s Army. The battalion took part in the battles of Griswoldville, Grahamville, Honey Hill and Savannah where Major. Cook was killed. After the Battle of Griswoldville Gen. P.J. Phillips reported that Maj. Cook and his men “participated fully in the action, deported themselves gallantly and . . . suffered much from wounds and death.” Leased by the Confederacy in 1865 the armory was operated until the close of the War. The old manufacturing property in Georgia was bought by the Athens Manufacturing Co. in 1870. Mr. Michel’s Notes State: “While all Confederate longarms, as well as the handguns, are relatively rare and the arms produced by Cook & Bro. no less so, there are only a very few surviving examples of the company’s initial production in New Orleans before being relocated to Athens, Georgia. This is a particularly fine example of that early production and is original throughout. The lockplate is well marked “Cook & Brother NO 1861” forward of the hammer with the Confederate national appearing at the tail. All parts bear the same serial number 41, on the nosecap, bands, barrel, lockplate, trigger guard, and buttplate.” CONDITION: Fine. These firearms were finished in the “white” and this example has aged to a pleasant grey color with its brass furniture having a medium yellow patina. This rifle has been lightly cleaned but it does not detract from its appearance. There is some medium to deep pitting on the barrel near the breech. The barrel “twist” is very visible, all markings are clear and most edges sharp. The stock is quite nice with only a small chip missing at the barrel tang. Ramrod appears to be original to the rifle. 4-31288 CW10 (20,000-25,000)

COOK & BROTHER ATHENS, GEORGIA RIFLE. SN 6188. This is your standard, 33″ Athens-made, Cook & Brother rifle. Lock on this gun is marked “Cook & Brother / Athens, GA / 1864 / 6188”. These markings all occur forward of hammer. Confederate 1st National Flag is stamped rear of hammer. Bbl is marked on top “Cook & Brother / Athens GA / 1864” and also SN “6188”. Rear band and nose cap are also serial numbered “6188”. Lock screws and tang screw are also serial numbered “6188”. Screws are buffed, however their serial numbers are difficult to read. Several two-digit secondary or assembly numbers are found on other parts. According to Mr. Michel’s notes, “With the fall of New Orleans, Cook & Brother moved production to Athens, GA, where this two-band rifle was produced. In extraordinary condition and all original throughout, the lockplate is well marked, forward of the hammer, ‘Cook & Brother’ and ‘Athens Ga 1864’ and at tail a depiction of the Confederate National Flag. All components, nose cap guards, barrel, lockplate, triggerguard, and buttplate are all marked with serial number 6188, indicating it was made close to the end of company production. Provenance: Yale University, Jack Malloy” This is a really fine Cook rifle in condition not often found on these guns. The gun was cleaned in the style in which institutions used to clean guns in the early 20th century. CONDITION: Metal surfaces on this gun have been cleaned bright, making some markings and SNs difficult to fully read. Bbl clearly shows the twist where bbl was made from twisted iron. Brass bands, trigger guard, nose cap, and buttplate are cleaned and polished. Stock is lightly sanded and varnished, but still retains fairly sharp edges. A 4″ x 1/2″ large sliver of wood has been replaced, adjacent to ramrod channel between bands. There is also a repaired chip approx. 1″ at toe of buttstock 4-31289 JS127 (20,000-25,000)

DAVIS & BOZEMAN RIFLE. SN 280. Davis & Bozeman firearms are quite scarce and are rarely encountered. The lock on this gun, though lightly marked reads “B&D/ALA” forward of hammer. Rear of hammer on lock, gun is dated 1864. Bbl is proofed “ALA/1864” though the “4” is only partially struck. Bbl, breech, and stock are all internally marked “XXXIX”. Bbl is also stamped on bottom “73”. SN “280” occurs on back of hammer and inside lock. Stock exhibits some fancy floral carving with large initials “JB”, probably denoting the gun’s owner. Mr. Michel notes that this gun is 1 of fewer than 10 of these rifles known to survive today, and this is one of very few outside a museum collection. This is indeed a very rare Confederate rifle, and this may be your only chance to buy one, especially as nice and presentable as this one. CONDITION: Bbl is gray/bright with scattered areas of staining and pitting. Both front and rear sights are complete. Bore is well worn; however, rifling is still present. Stock has repair just above lock. Brass buttplate, trigger guard, and nose cap are cleaned and smooth with scattered scratches and dents. Lockplate markings are discernible but typically light struck. SN “280” is well struck inside lock and inside hammer. Front band appears to be restored. 4-31298 JS122 (20,000-30,000)

COLUMBUS ARMORY RIFLE. SN 73. Cal. 58. Several Confederate rifles made by various makers in Columbus, GA and the surrounding area have similar features. Among these makers are J. P. Murray, Columbus Armory, Dickson, Nelson, and David & Bozeman. All these manufacturers shared similarly designed carbines and MS-style rifles. All these makers normally marked their guns, with exception of the Columbus Armory, where only 2 or 3 marked specimens are known. Based on this information, we believe this unmarked gun to be a product of the Columbus Armory. Earlier literature usually identifies these guns as J. P. Murray. Bbl of this gun is inspected “PRO. / F.C.H.” which is seen on known J. P. Murray and Columbus Armory weapons. Information on the Columbus Armory only recently has come to light in the marvelous book by John Murphy and Howard Madaus, Confederate Carbines and Musketoons. Murphy and Madaus, in their book, describe the Confederate contract to Columbus Armory for 200 guns in 1862, to be inspected by Capt. F. C. Humphries, who inspected this gun. John D. Gray, the owner of the Columbus Armory, was paid for 183 guns. This gun, SN 73, certainly falls in that range. Mr. Michel, in his notes, describes the markings and restoration of this gun as follows: “The lockplate is unmarked, but the barrel in characteristically marked ‘PRO. / F.C.H’. The sideplate is marked ‘VI’ and the barrel underside marked ’73’, while the inside of the lockplate is marked both ‘VI’ and ’73’. The fore-end has been added from underneath the rear band to the front band and nose cap. On the barrel is an original and correct Boyle & Gamble brass saber bayonet adapter”. CONDITION: Bbl is brown/black with scattered pitting. Bbl proofs are clear and well stamped. There is a partially discernible “224” stamped about 3″ from muzzle end on top of bbl. The attached Boyle & Gamble bayonet adapter is serial numbered “46” and has a rich, “excavated”-type patina. Brass buttplate and trigger guard are well patinaed over scattered nicks and scratches. Front bbl band and possibly rear bbl band, are replacements, as is forestock forward of rear band, ramrod, and rear sight. 4-31299 JS121 (8,000-12,000)

DICKSON, NELSON & CO RIFLE. SN NSN. Cal. 54. This Confederate copy of a Mississippi rifle was made in Dawson, GA, in 1865. Lock is marked forward of hammer “Dickson / Nelson & Co / CS”. Rear of hammer is marked “ALA / 1865”. Bbl is not dated but is stamped internally with a small “G” and a large “R” near breech plug. Murphy and Madaus in their book Confederate Rifles and Muskets stated, “There are no external stampings on the barrels. The internal surface of the lockplate is unmarked. The under surface of the barrel of many specimens studied is stamped with a small ‘G’. The significance of this marking is not known at this time, but it probably is the initial of one of the workmen who inspected finished arms at the plant”. Like other guns of this manufacture, gun exhibits brass buttplate, trigger guard, nosecap, and clamping bands. Gun appears orig and complete in every regard, with possible exception of replaced front sling swivel. Ramrod appears orig to this gun, though of foreign manufacture. Mr. Michel, in his notes, states that this gun was cataloged by Robert Abels in his catalog #34. This gun was item #6. CONDITION: Bbl is gray, cleaned and pitted, especially at breech. Lock is gray and smooth. Markings are clear. Brass buttplate, trigger guard, bands, and nosecap are smooth with nice patina. Stock is sound with scattered dings, gouges, scratches. Repaired hairline crack in front of lock and about a 1″ piece of wood replaced behind bolster. 4-31300 JS133 (18,000-25,000)

READ & WATSON TYPE 1 RIFLE. SN 186. Cal. 64. This scarce gun is being offered in near “attic” condition. Accompanied by orig Hall bayonet which fits gun snugly. Surfaces are mostly untouched, with exception of apparent contemporary repair to wrist. SN is stamped below nipple, on breech. Also serial number on bottom of buttstock “C186”. Mr. Michel, in his notes, tells the history of this specimen as follows: “Long assumed to have been made from parts captured at Harpers Ferry that were thereafter assembled by J. B. Barret in Wytheville, Virginia, it is now clear that these rifles were actually assembled by N. T. Read and John J. Watson of Danville from carbines and rifles the state had received prior to the outbreak of the war under the Militia Act. In the process of altering the rifles, the original Hall breech block and frame were replaced by a brass breech piece with a centrally positioned iron breech plug for the barrel into which a nipple was screwed. The new breech piece is a small, narrow insert, only the rear tang of which extends part way back along the top of the wrist of the stock. Original Hall parts are used as the barrels, barrel bands, buttplates, triggers, and trigger guards. The buttstock is of new manufacture. The forestock is original, joined with a staple. Serial numbers appear on the underside of the buttstock and on the breech below the nipple”. CONDITION: Bbl and other iron parts are gray/brown with scattered staining and pitting. Old varnish on bbl is discolored. Stock exhibits numerous scratches, nicks, and dings, along with an old repair to wrist, visible on back side of gun. Brass breech is smooth with good patina over scattered nicks. 4-31305 JS119 (12,000-15,000)

READ & WATSON TYPE II RIFLE. SN Not noted. Cal. 64. Mr. Michel describes this rifle as follows: “Now known to be the product of N. T. Read and John J. Watson of Danville, Virginia, using rifles and carbines which had been supplied under the Militia Act to the state of Virginia prior to the outbreak of the war, these rifles represent an unusual conversion from breechloader to muzzle loading arm, instead of the more usual reverse. The Type II variation of this rifle has a breech piece of brass cut significantly larger than that of the Type I. This breech piece is bulky, with a heavy rearward extending tang which covers the top of the wrist of the stock and the top front part of the comb of the stock. The serial number is a Roman numeral in the bottom of the brass breech piece and a letter in conjunction with an Arabic number on the curved forward face on the bottom of the breech piece”. Type II Read & Watsons are quite scarce with the large, brass breeches. You are bidding on a nice example of this rarely offered rifle with an accompanying, correct Hall bayonet. Mr. Michel’s Notes State: “Now known to be the product of N. . Read and John J. Watson of Danville, Virginia, using rifles and carbines which had been supplied under the Militia Act to the State of Virginia prior to the outbreak of he war, these rifles represent an unusual conversion from breechloader to muzzle loading arm, instead of the more usual reverse. The Type II version of this rifle has a breechpiece of brass but significantly larger than that of the Type I. This breechpiece is bulky with a heavy rearward-extending tang which covers the top of the wrist of the stock and the top front part of the comb of the stock. The serial number is a Roman numeral in the bottom of the brass breech piece and a letter in conjunction with an Arabic number, a Roman numeral, or other letter on the curved face of the bottom of the breechpiece.” PROVENANCE: Ben Michel collection. CONDITION: Bbl and other iron parts are gray with scattered areas of staining and pitting. Old Harpers Ferry “NWP” inspector mark visible on breech. Stock is sound, with numerous dings, dents. Several chips to ramrod channel. Stock retains some varnish. Brass breech has nice patina over scratches and dings. 4-31304 JS120 (12,000-15,000)

UNKNOWN CONFEDERATE MISSISSIPPI RIFLE. SN NSN. This is a most unusual gun. At first sight, it appears to be a standard contract MS; however, the brass bands on this gun are pinned, it contains a much larger diameter ramrod, patchbox mortise is very odd and crudely cut, and lockplate is simply marked “Manton”, and hammer is unusual and appears cast. No other markings are seen. Small brass bayonet adapter is attached to bbl about 4″ from muzzle. This is a very unusual gun. We have not seen another assemblage like it. Mr. Michel’s Notes State: “Confederate copy of M1841 rifle. Lockplate marked in small English letters “Manton”. Patchbox inlet with hand drill marks. Two brass bands are fastened with iron nail passing through the stock. Barrel is unmarked. Brass saber bayonet adapter with small lug.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is brown with scattered pitting. Bbl appears heated near muzzle. Front sight is replaced. Stock exhibits numerous nicks and scratches. One hairline crack opposite lock. Approx. 3″ piece of wood is restored above lock at breech. Brass bands, trigger guard, buttplate, and patchbox exhibit good patination over numerous scratches and scrapes. Lock and hammer are cleaned and pitted. Trigger and sling swivels are dark and pitted. 4-31307 JS123 (2,000-5,000)

RICHMOND ASSEMBLED RIFLED MUSKET. SN NSN. Cal. 58. Mr. Michel, in his notes, describes this gun as “Model 1861 Richmond rifled musket”. He describes the gun as follows: “This rifled musket represents the first type assembled with parts taken from Harpers Ferry after the capture of the arsenal and armory by Virginia state trooops at the outset of the war. Lockplate is of the high hump configuration of the Model 1855 lockplate but has never been milled for the Maynard primer mechanism and is totally unmarked. Bbl is similarly unmarked and has no cutout for a rear sight. Forestock has been restored, but bbl is orig full 40″ length.” CONDITION: Bbl and lock are brown with scattered pitting. Lock retains 1855 hammer. Iron buttplate is U.S. surcharged. Nosecap is brown and heavily pitted. Bands, ramrod, and trigger guard are brown and smooth with scattered pitting. Bbl exhibits no discernible rifling. Stock is cut under rear band and restored forward. Stock is lightly sanded and has about a 3″ repair behind lock, adjacent to bolster. 4-31240 JS170 (2,000-4,000)

1861 RICHMOND RIFLED MUSKET. SN NSN. Cal. 58. Mr. Michel, in his notes, describes this gun as follows: “This rifled musket represents the first type produced at Richmond before the takeover by the central government and subsequent marking with the ‘CS’ designation. Lockplate is marked forward of the hammer ‘Richmond Va’ and at tail ‘1861’. Gun retains both orig sights. Rifling is visible, though faint. No bbl date or proofs are visible due to rust and pitting. Stock has correct 1855-style mortise under lock, as to be expected on an 1861 Richmond assemblage. Ramrod has interesting repair, where orig tulip-shaped end has been repaired by blacksmith with 1/4” cylindrical tip. CONDITION: Bbl bands, iron buttplate, and nosecap are brown and pitted, as is trigger guard. Lockplate and hammer are gray with scattered areas of muted casecolor and pitting. Ramrod is gray/brown with scattered areas of pitting. Stock is solid and has typical red color often encountered in these guns. There are numerous dings, gouges, scrapes, and scratches, especially on wood opposite lock. 4-31242 JS152 (4,000-6,000)

MODEL 1861 RICHMOND RIFLED MUSKET. SN NSN. Cal. 58. This early 1861 Richmond still retains the Model 1855 hammer and a surcharged US Model 1855 buttplate. Mr. Michel describes this gun further as follows: “This rifled musket represents the first type assembled with parts taken from Harpers Ferry after the capture of the arsenal and armory by Virginia state troops at the outset of the war. The lockplate is marked ‘Richmond Va’ indicating it is one assembled after movement of the parts to that city but still using old parts, as bbl uses the Model 1855 long-range rear sight not produced at Richmond. Lockplate itself has been modified, again subsequent to orig assembly by being ground at the hump top to level the plate to the contour of the stock, much like the plates subsequently produced at Richmond”. CONDITION: Bbl is brown and apparently refinished. No rifling is visible in bore. Stock is restored from rear band forward as are ramrod, nosecap, and bands. Buttstock has old repair at wrist. Blacksmith-made ramrod appears orig to era. Long-range rear sight is replaced. Accompanying ramrod is pitted on socket and blade is gray with scattered staining and pitting. 4-31241 JS153 (3,000-5,000)

1862 RICHMOND RIFLED MUSKET SN NSN. Cal. 58. Lock is marked and dated “CS / Richmond Va / 1862”, and lock now has a Richmond manufactured hammer. Bbl is dated “1861” with proper “VP / eagle head” proofs. Buttplate is brass. Nosecap is iron. Mr. Michel, according to his notes, states the following: “This rifled musket represents the first marked after the takeover by the central government of the Confederacy as indicated by the lockplate marking of ‘CS’ over ‘Richmond Va’ forward of the hammer. The date ‘1862’ appears at the tail of the lockplate which still is of the high hump form.” CONDITION: Bbl is cleaned and gray with scattered areas of pitting and staining. Lock is gray/brown with numerous nicks and scratches. Markings are good. Stock is restored from middle band forward, as is front band and nosecap. Stock has repair at left of bolster tang. Ramrod is correct style, Model 1855 with swell. Attached Confederate sling is good, missing leather reinforcement strip, with some fraying at edges. Accompanying bayonet is cleaned with scattered staining and pitting. 4-31243 JS154 (6,000-9,000)

1862 RICHMOND RIFLED MUSKET. SN NSN. Cal. 58. At some point in 1862, Richmond ran out of or quit using Harpers Ferry parts, and guns could be all Richmond manufactured, including brass buttplate and nosecap, bands with centrally-stamped “U’s”. Bbls and trigger guards typically show stress lines in the metal. Lockplates now have a low hump, which is characteristic of all further production of Richmond locks through the end of the war. This gun shows all these features, and is all Confederate Richmond-manufactured with exception of contemporarily replaced, blacksmith-made ramrod which fits gun well, and color matches well also. Accompanied by a matching .58 caliber unsurcharged 1855-style bayonet and orig Confederate linen sling. You are bidding on a very nice and presentable 1862-dated gun that is all orig, and better guns are difficult to find. Mr. Michel’s Notes State: “This rifled musket represents the final low hump configuration of the lockplate produced at Richmond. The lockplate is marked “CS / Richmond Va / 1862”. The buttplate is brass as is the nosecap. Provenance: Ex. coll. Carl Pugliese” CONDITION: Bbl is cleaned, gray/bright with areas of pitting, especially around breech. Front and rear sites appear orig. Bore is very worn; however, rifling is present. Other metal surfaces are cleaned and gray/bright. Brass nosecap and buttplate are smooth. Stock exhibits color often seen on Richmond wood. Initials “SHM” are scratched on right side of buttstock. Buttstock is sound; however, there are a few hairline cracks and one large gouge approx. 1″ x 1″ x 1/4″ deep on bottom. 4-31244 JS156 (9,000-15,000)

1863 RICHMOND RIFLED MUSKET. SN NSN. Cal. 58. This gun appears all orig and Richmond in manufacture. In 1863, most Richmonds encountered, if untouched, exhibit brass buttplate, brass nosecap, correct Richmond bands, Richmond bbl, lock, and hammer, and Richmond stock and ramrod, as does this example. This gun was once in the collection of Henry Stewart. You are bidding on a very nice, all orig, 1863-dated Richmond musket with an orig Confederate linen sling and accompanied by an unsurcharged, angular bayonet. This gun was probably made early in 1864, as bbl is dated “1864”. Armory was still probably utilizing the few remaining 1863 locks. Ben Michel’s Notes State: “This rifled musket is again typical of those produced under the central Confederate government. The lockplate is marked, forward of the hammer, “CS / Richmond Va” and at the tail, the date of production, “1863”. Both the buttplate and the nosecap are made of brass. Provenance: Ex. coll. Henry M. Stewart.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is gray/bright, showing typical Richmond stress lines longitudinally on bbl. Rifling is discernible, though bore is dark. Lock is gray and matches bbl well, as do bands. Brass buttplate and nosecap are well patinaed. Stock is sound with numerous nicks and dings throughout. Sling is good overall. Accompanying bayonet is gray with scattered pitting. Orig Richmond ramrod is 38-1/4″ long, so it has lost about 1″ of its orig length. 4-31245 JS157 (9,000-15,000)

1864 RICHMOND RIFLED MUSKET. SN NSN. Cal. 58. This is what we consider to be the standard late production 1864 Richmond rifled musket. Markings here are the most typically noted on 1864s. Nice 1864s, where barrel are usually deeply stamped, as they are here. The “VP” proof was changed from earlier models, like is seen here where the “VP” is deep and there is no break in the “P”. On all other Richmonds prior to this standard or late-production 1864, a broken “P” is generally noted. This gun shows tremendous stress marks in the metal on bbl, trigger guard, hammer, and even in the rear sight. This gun appears orig and complete in every regard. This gun must have been captured or made late in the war and saw little use, because there is little pitting from powder at breech, and the bore rifling is very good. You are bidding on a beautiful 1864-dated Richmond rifled musket that is orig and complete in every regard, really showing the last-ditch manufacture of the Confederacy, with an orig Confederate sling and accompanying proper bayonet. CONDITION: Metal surfaces are cleaned and are gray/bright. Markings on bbl and lock are very good. Brass nosecap and buttplate are smooth and patinaed with scattered scratches. Stock is sound and solid with scattered dings and scratches. In front of comb of stock, there is a small, cross-hatched, carved area. 4-31246 JS158 (10,000-15,000)

RICHMOND MUSKETOON. SN NSN. Cal. 58. As Mr. Michel will later state, these 30″ bbl musketoons or short rifles are quite controversial as to their origin. This gun does indeed have correct Richmond lock and hammer, the “VP” proof has a broken “P” as is expected in Harpers Ferry and Richmond-produced guns. Trigger guard shows metal faults commonly seen in Richmonds. Mr. Michel states in his notes: “Although this weapon is the subject of some controversy as a result of its unusual configuration and the lack of a specific reference to it in the Richmond production records, examples, albeit rare, are to be found in old collections of Confederate weapons. Further, the catalog of September 1870 stores of condemned ordnance at the Springfield Armory does list some 318 Richmonds ‘altered to smooth bore’ as are these musketoons. The bbl is 30″ in length with 2 bands comprising the rear and middle bands of a 3-band rifled musket. Stock tip and buttplate are iron. Lock is a standard Richmond 1863 low humpback lock. Most unique about this arm is the slimming of the stock around the lockplate and the flat on the left side of the stock opposite the lockplate. With original 15″ bayonet, narrowed blade and unmarked. It is my opinion that these musketoons are the subject of the reference in the October 12, 1863 report by W. S. Downer, Superintendent of the CS Armory in Richmond to Josiah Gorgas, Chief of Ordnance, providing a production report for the Richmond Armory for the fiscal year ending September 30, 1863. In that report he lists 651 ‘new smooth bore carbines cal. 69’ distinct from 2791 ‘new rifle carbines caliber 58′”. CONDITION: Metal surfaces are gray with scattered pitting. Stock is sound with numerous dings and dents. Bbl shows no rifling, as a smooth bore should. Petite 15-1/2″ bladed bayonet fits gun snugly. Bayonet is cleaned and matches color of bbl. 4-31248 JS155 (3,000-6,000)

1863 RICHMOND CARBINE. SN NSN. Cal. 58. Mr. Michel describes this gun as follows: “In 1863, Richmond began production of a ‘new rifled carbine.’ The bbl is 25″ in length with a special front sight having a wide base and pinch sight form. Forestock is held by 2 bands, same as the rear and middle band with sling swivel of a 3-band rifled musket. Nosecap and buttplate are of brass. Sling swivel on a screw base is located behind the trigger guard plate, although a sling swivel continues to also appear on the trigger guard bow. Lockplate is marked forward of the hammer ‘CS / Richmond Va’ and at the tail is dated ‘1863’. You are bidding on a fine, solid 1863-dated carbine which is complete and orig. These carbines are generally well used, and this is a beautiful example. CONDITION: Bbl is brown/black with pitting. Rifling is good, though pitted. Bbl retains orig front and rear sights, which are complete. Bands, trigger guard, and sling swivels are brown and pitted. Ramrod is brown and smooth and may be replaced, but it is an orig rod. Brass nosecap and buttplate exhibit good patina with scattered scratches. Stock is sound, exhibiting numerous scratches, scrapes, and nicks. 1” crack is found forward of lock. Wood is repaired around read sling swivel. 4-31249 JS159 (9,000-15,000)

1864 RICHMOND CARBINE. SN NSN. Cal. 58. Mr. Michel, in his notes, states, “The final production year of the ‘new rifled carbine’ first produced in 1863. The 25″ long bbl has a special front sight with a wide base and pinched sight form. The 2 bands are the same as the rear and middle bands as a 3-band rifled musket. There are 3 sling swivels, one on the front band, one on the trigger bow, and one on a screw based located behind the trigger guard plate. Nosecap and buttplate are of brass. Lockplate is marked forward of the hammer ‘CS / Richmond Va’ and at the tail is the date ‘1864’. Armory records include only 2 carbines produced in January 1865.” You are bidding on a last year of production, 1864-dated Richmond carbine with lock and bbl date. These guns saw generally very hard use, and pitting at bolster most often obliterated bbl dates. This gun exhibits a strong 1864 bbl date. Stock on this gun is superior, showing sharp edges and some orig varnish. CONDITION: Bbl is brown/black with pitting. Bbl retains orig front and rear sights, which are very good. Rifling is good. Lock is dark and pitted. Trigger guard and bands and ramrod are cleaned with scattered pitting. 2 small initials, possibly inspector, are stamped rear of trigger guard. These initials are possibly “JB” or “JH”. Stock is sound with good edges and some orig varnish over numerous small gouges, scrapes, and scratches. Initials “WSP” are scratched in left flat of buttstock. Brass nosecap and buttplate exhibit good patina. Ramrod has solid tulip end, not of Richmond manufacture, but fits gun well and presents nicely with it. 4-31250 JS160 (9,000-15,000)

RICHMOND ASSEMBLED CARBINE. SN NSN. Cal. 58. A very rare form of Richmond Altered Carbine predating the 1863 Rifled carbine. Only a few these are known to still exist. Mr. Michel, in his notes calls this gun a “Richmond Model 1842 Altered Carbine” and describes it as follows: “In 1862, Richmond produced a limited number of carbines having the lock, stock, and bbl of the Model 1842 musket. Bbl has been shortened to 25″ with a front sight of the wide base and pinched sight of the Richmond rifled carbine and rifle. Stock is cut back to between front band and muzzle, and the wood simply rounded off. There is no nosecap. Like the Richmond rifled carbine, there are three sling swivels, one in the front band, one on the trigger guard bow, and one on a screw base located behind the trigger guard plate.” CONDITION: Metal surfaces with exception of rear sling swivel are brown, smooth with scattered pitting. Rear sling swivel is brown and pitted. Front sling swivel is restored. Ramrod has solid tulip end and color matches other metal on this gun. 4-31252(3,000-5,000)

RICHMOND ASSEMBLED CARBINE. SN NSN. Cal. 58. This gun was evidently captured by Jacob B. Stauffer of the PA 197th Infantry. His initials and name occur 3 times on this gun. Gun is made of both Richmond and Springfield parts. Similar guns with 1861 Springfield locks are pictured in Murphy & Madaus, along with other references. Gun is in very good, untouched condition, exhibiting good fit and very good condition overall. Mr. Michel, in his notes, states the following: “In addition to the repair and modification of rifled muskets to rifles, Richmond also modified, in the same fashion, a number of rifled muskets to the same configuration as Richmond-made rifled carbines. These rifled muskets had the bbls cut to 25″ and typical Richmond carbine and rifle sight installed. In all other respects as well, these carbines were made to conform to the Richmond carbine. Very few of these carbines are known to still exist, of which this is one of the finest examples.” CONDITION: Iron surfaces are gray/bright with good markings, brass nosecap is well patinaed. Ramrod appears orig but is cut back about 1″. Rifling is very good. 4-31258 JS168 (6,000-8,000)

RICHMOND RIFLE. SN NSN. Cal. 58. Mr. Michel describes this 1864 rifle as follows: “In 1864 Richmond began production of a very limited number of ‘short rifles.’ This example is typical with a 33″ bbl. Forestock is held by 2 bands, with the forward band being the same as a middle band with sling swivel of a 3-band rifled musket. Front sight is different from the sight of the 3-band rifled musket. It has a larger base with a pinched sight form. It is the same as appears on the Richmond carbine. Nosecap is of brass on the stock extension forward of the front band. Buttplate is also of brass. Lockplate is marked forward of the hammer ‘CS / Richmond Va’ and at the tail is dated ‘1864’.” The scarcest configuration of Richmond Armory products is the 33″ Richmond Rifle. Production didn’t start until 1864; however, Richmond rifles are found with a variety of lock dates, locks and parts. Battlefield gleanings and captured damaged guns resulted in a variety of 33″ Richmond rifles. Scarcest of the 33″ rifles have mostly Richmond manufactured parts and will be dated 1864, as is this gun. CONDITION: Bbl is brown/black with pitting. Rifling is discernible, though pitted. Bbl retains orig front and rear sights, though leaves of rear sight are restored. Bands, trigger guard, and sling swivels are brown. Ramrod appears orig to this gun; however, it appears converted from an earlier musket. Stock is sound with areas of orig varnish. Stock exhibits a hairline crack back of lock along with scratches and nicks. Initials “BCL” are carved into flat of left buttstock. These initials probably denoted the Confederate who carried this gun. 4-31247 JS161 (12,000-16,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This Richmond assembled rifle used various Springfield parts, including 1863 clamping bands and 1861 Springfield lock and iron nosecap. Springfield stock retains its U.S. surcharged buttplate. Bbl has had all proofmarks removed, but does exhibit the pinched front sight that is only found on Richmond rifles and carbines. Mr. Michel, in his notes, states, “Model 1863 (with clamping bands) stock with Model 1861 barrel with 1861-dated lockplate, all combined. Typical of the mixture of parts found on these Richmond reworked rifles made of battlefield-recovered parts of rifled muskets.” CONDITION: Bbl is cleaned with scattered pitting. Rear sight is Springfield, and it retains scattered finish under pitting. Cone and clean-out screw in bolster are replaced. Rifling is good. Ramrod is Springfield and is about 31″ long. Stock is solid with scattered nicks and scrapes and several wood putty repairs. 4-31259 JS163 (4,000-6,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This heavily pitted, untouched gun has well patinaed, Richmond brass nosecap, Richmond pinched front sight, and other Springfield and Richmond parts. Ramrod, which fits gun nicely, is blacksmith forged. Mr. Michel’s Notes State: “ In addition to the production of new rifled muskets, musketoons, rifles, and carbines, Richmond repaired an unknown total number of rifled muskets, many of which were undoubtedly the gleanings of battlefields left in the possession of Confederate troops. A certain number of these Richmond repaired weapons may be conclusively identified as having been repaired at Richmond. All share the same characteristics. In each case, the barrel has been shortened from 40” to 33” with the addition of a new front sight of the wide base pinched form used on the Richmond rifle and rifled carbine. The front barrel has been removed leaving only the original rear and middle barrel. The shortened forestock has been given a brass nosecap. Most of these rifles show hard usage, into battle, lost, recovered, repaired, and reissued. They are all true “veterans” of the war. Model 1863/61. A gun with character, well used with a tin wrist repair nailed in place. All parts heavily rusted, but overall giving a great, “out of the barn” look.” CONDITION: All iron parts are brown/black and heavily pitted. Rifling in bore is very good, though pitted. Stock has numerous dings and scratches. Old wrist repair, as described above, is solid and matches overall condition of gun. 4-31260 JS164 (4,000-6,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This Richmond assembled rifle consists of 1861-dated Springfield lock, stock, and bbl. Bands are of Confederate manufacture, showing proper Richmond styles and placements of “U’s”. Buttplate is orig to stock and surcharged “U.S.”. When bbl was shortened, a pinched rear sight was added. When stock was shortened, it was nicely tapered and Confederate brass nosecap was attached. Bbl retains orig Springfield rear sight. This is a classic example of a Richmond alteration of a battlefield gleaned, and probably damaged, rifled-musket. Mr. Michel’s Notes State: “In addition to the production of new rifled muskets, musketoons, rifles, and carbines, Richmond repaired an unknown total number of rifled muskets, many of which were undoubtedly the gleanings of battlefields left in the possession of Confederate troops. A certain number of these Richmond repaired weapons may be conclusively identified as having been repaired at Richmond. All share the same characteristics. In each case, the barrel has been shortened from 40” to 33” with the addition of a new front sight of the wide base pinched form used on the Richmond rifle and rifled carbine. The front barrel has been removed leaving only the original rear and middle barrel. The shortened forestock has been given a brass nosecap. Most of these rifles show hard usage, into battle, lost, recovered, repaired, and reissued. They are all true “veterans” of the war. Model 1861.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are cleaned with pitting. Bbl retains no markings. Lock markings are clear and discernible. No discernible inspectors’ marks are found in stock. Stock overall is sound with scattered dings and scrapes. Ramrod is probable replacement. 4-31255 JS162 (4,000-6,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This Richmond constructed rifle consists of an 1855 rifled musket stock with patchbox and Bridesburg 1863-dated lock. Bbl appears to be model 1855, Harper’s Ferry or Richmond manufactured. Rear sight was not removed to check mortising to ascertain. This assemblage has a nice, untouched look, being dark and uncleaned. You are bidding on a relatively as found “attic” or “barn-found” Richmond assembled rifle from captured parts. Mr. Michel’s Notes State: “In addition to the production of new rifled muskets, musketoons, rifles, and carbines, Richmond repaired an unknown total number of rifled muskets, many of which were undoubtedly the gleanings of battlefields left in the possession of Confederate troops. A certain number of these Richmond repaired weapons may be conclusively identified as having been repaired at Richmond. All share the same characteristics. In each case, the barrel has been shortened from 40” to 33” with the addition of a new front sight of the wide base pinched form used on the Richmond rifle and rifled carbine. The front barrel has been removed leaving only the original rear and middle barrel. The shortened forestock has been given a brass nosecap. Most of these rifles show hard usage, into battle, lost, recovered, repaired, and reissued. They are all true “veterans” of the war. Model 1863 Bridesburg.” PROVENANCE: Ben Michel collection. CONDITION: All metal surfaces are dark and pitted. Bbl exhibits no discernible rifling. Markings are mostly discernible, though partially obscured by pitting and patina. Brass nosecap exhibits deep patination. Model 1855 ramrod is brown and smooth. Stock is sound with scattered areas of orig varnish with numerous scratches, nicks, and dings. About a 1″ area of wood behind bolster is burned out from use. 4-31256 JS166 (4,000-6,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This particular Richmond assemblage utilizes an 1859-dated, Model 1855 Springfield lock with Maynard tape device and door removed. Stock appears to be 1855 pattern manufacture also. Bbl is either Richmond or Harpers Ferry manufacture as denoted by broken “P” in “VP” proof. Bbl is also missing rear sight, so set screw mortise appears Richmond Manufacture. Rear band appears to be Richmond manufactured, as front band appears Springfield or Harpers Ferry. Brass nosecap and buttplate are of Richmond manufacture. Pinched front sight of Richmond manufacture has been cut to a short blade. You are bidding on an apparently all orig, Richmond assembled rifle from various battlefield gleaned parts. Mr. Michel’s Notes State: “In addition to the production of new rifled muskets, musketoons, rifles, and carbines, Richmond repaired an unknown total number of rifled muskets, many of which were undoubtedly the gleanings of battlefields left in the possession of Confederate troops. A certain number of these Richmond repaired weapons may be conclusively identified as having been repaired at Richmond. All share the same characteristics. In each case, the barrel has been shortened from 40” to 33” with the addition of a new front sight of the wide base pinched form used on the Richmond rifle and rifled carbine. The front barrel has been removed leaving only the original rear and middle barrel. The shortened forestock has been given a brass nosecap. Most of these rifles show hard usage, into battle, lost, recovered, repaired, and reissued. They are all true “veterans” of the war. Model 1855.” PROVENANCE: Ben Michel collection. CONDITION: Iron surfaces are gray/brown with scattered pitting. Brass buttplate and nosecap are well patinaed over several scratches. Stock is solid with scattered scratches, dings, and gouges. Rifling in bbl is very good. Ramrod is gray and pitted and appears to be a cut-down 1855 ramrod for rifled musket. 4-31253 JS167 (4,000-6,000)

RICHMOND ASSEMBLED RIFLE. SN NSN. Cal. 58. This Richmond altered rifle began life with parts from a Colt Special Model 1861 musket. This specimen, being dated 1863. Gun retains Colt lock, stock, bbl, and bands or the orig Colt configuration. Richmond has shortened bbl to 33″, incorporating its distinctive pinched sight, tapering the forestock to accept Richmond brass nosecap. Gun appears overall to be all orig and in very good condition. Murphy & Madaus in their text show a similarly altered Colt Special Model alteration by Richmond, but with 36″ bbl. Mr. Michel’s Notes State: “In addition to the production of new rifled muskets, musketoons, rifles, and carbines, Richmond repaired an unknown total number of rifled muskets, many of which were undoubtedly the gleanings of battlefields left in the possession of Confederate troops. A certain number of these Richmond repaired weapons may be conclusively identified as having been repaired at Richmond. All share the same characteristics. In each case, the barrel has been shortened from 40” to 33” with the addition of a new front sight of the wide base pinched form used on the Richmond rifle and rifled carbine. The front barrel has been removed leaving only the original rear and middle barrel. The shortened forestock has been given a brass nosecap. Most of these rifles show hard usage, into battle, lost, recovered, repaired, and reissued. They are all true “veterans” of the war. Model 1861 Colt.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are gray/brown with scattered pitting. Rifling to bore is very good. Stock is sound with scattered dings and scrapes. 4-31257 JS165 (4,000-6,000)

CONFEDERATE, SOUTH CAROLINA ASSEMBLED, MODEL 1842 MUSKET. SN NSN. Cal. 69. This “attic” condition musket appears in as-found condition. Colors of metal and wood match throughout with possible addition of ramrod. Bbl has standard “VP” / eagle proof as found on some Palmetto muskets, and buttplate is surcharged “SC” which is also typical of Palmetto muskets. Lockplate is unmarked and shows some metal stress lines typical of Confederate or U.S. Condemned manufacture. Stock is made from parts assembled from 2 guns. Note the marriage under rear band of forestock and buttstock. This gun has been together and stored for a long time such that staining and patina match both pieces of wood to bbl band and musket bbl. Mr. Michel described this gun as follows: “Generally a Model 1842 musket in configuration, but stock from buttplate to rear band is crudely made with forend joined under rear band, which is turned rearward to support join between butt and forestock. Buttplate is from Palmetto musket, stamped ‘SC’. Lockplate is unmarked but does not appear to have been filed to remove markings. Inletting for lockplate has been done with circular hand drill. Three bands are all orig M1842 type. Although stock is pieced, both sections are unquestionably orig and vintage”. CONDITION: All metal surfaces are uncleaned, brown and pitted. Stock in 2 pcs is sound with scattered dings, scrapes, and scratches with no discernible markings. Bbl proofs and “SC” surcharge are clear. 4-31251 JS198 (3,000-5,000)

MISSISSIPPI CONFEDERATE ALTERATION OF HALL RIFLE. SN NSN. Cal. 64. Mr. Michel describes this gun as follows: “Alteration to percussion of Model 1819 Hall rifle. Breechblock marked ‘J. Hall / H. Ferry / US / 1831’. This alteration performed by brazing a striker onto the bottom jaw of the original flintlock hammer. This newly formed hammer strikes vertically a nipple screwed into the breechblock from which the original pan has been filled in. Exactly the same alteration appears on a North contract Hall rifle, on which the top of the receiver is stamped ‘S. Carolina'”. Murphy & Madaus show in Confederate Rifles and Muskets, plates 23 & 24, p. 334, a nearly identical specimen of an 1832-dated Hall that is attributed to a Mississippi armory. This alteration, according to Murphy & Madaus, was “thought to have either occurred at the Holly Springs Armory or Columbus (Briarfield) Arsenal. As with those altered rifles, the chamber block was removed from the frame, and the flintlock battery was removed from the block. Upper and right surfaces from the block were ground to eliminate the projections from the pan, its fence, and the frizzen supports. The indentation in the upper right top of the block that permitted the toe of the frizzen to rotate, however, was not filled in. The former vent was enlarged and threaded; into the newly-threaded hold a percussion code was screwed at a 90-degree angle to the top of the block. The old flintlock cock was cut above the throat, so as to remove the jaws and jaw screw. In place of those parts a new top section incorporating a striker and spur was brazed to the lower section of the cock. The percussion hammer then was re-attached to the chamber block, and the block was re-inserted into the frame. No reassembly marks were applied to the rifles during the process of alteration”. You are bidding on a complete and orig example of the distinctive, massive, brazed-hammer variety of Confederate altered Halls. CONDITION: Bbl and other metal surfaces are black with scattered scuffing and pitting. Stock is sound with scattered dings and scratches. Initials “WJC” are scratched lightly into right side of buttstock. Multi-grooved Hall rifling is very good. Front bbl band is partially cleaned, showing a brown surface under the black surface of other bands and rest of metals surfaces on this gun. Ramrod is bright. 4-31286 JS146 (3,000-5,000)

FAYETTEVILLE ALTERATION OF A HALL CARBINE. SN NSN. Cal. 52. Mr. Michel, in his notes, describes this carbine as follows: “Alteration to percussion and carbine length of a Model 1819 Hall rifle. Breechblock is marked “J. Hall / H. Ferry / U.S / 1834″, which is typical of Fayetteville alterations. Breechblock has the frizzen removed and the flintlock hammer replaced with a percussion hammer with knurling on the hammer spur. A nipple has been screwed into the area of the former pan. The bbl has been cut to a length of some 22-3/4” and the forestock shortened accordingly. It is held by the orig rear and middle bands, both being pin-fastened with the orig double-strap front band discarded. Trigger guard bow is retained, but the hand grip curving strap of the orig rifle is replaced by a strap following the contour of the stock. Edges of the stock appear to have been thinned and smoothed. This gun is illustrated inConfederate Carbines & Musketoons by John Murphy, p.99, plates 108-109.” CONDITION: Metal surfaces are gray with scattered pitting and staining. Multi-grooved Hall rifling is very good. Stock is sound with a 2″ chip missing at muzzle and a 9″ x 1/2″ sliver missing below frame on left side exposing the mechanism. There is also a 1-1/4″ x 1-1/4″ repair to top of buttstock just behind frame. 4-31287(5,000-7,000)

TEXAS CONFEDERATE ALTERATION OF HALL RIFLE. SN NSN. Cal. 64. Mr. Michel describes this alteration as follows: “Alteration to percussion of Model 1819 Hall rifle. Breechblock marked ‘J. Hall / H. Ferry / U.S. / 1832’. This alteration performed by brazing a somewhat crude percussion hammer onto the base of the orig flintlock hammer. No remnant of the bottom jaw or hole remains. Nipple has been screwed into the orig pan which retains the rear fence. This example was recovered in Texas”. You are bidding on a most unusual and possibly unique welded hammer conversion as described above. CONDITION: Iron surfaces are brown with scattered nicks, dings, and pitting. Breech screw and trigger are replaced. Stock has several wood repairs and is missing several pieces, including a 5″ x 3/4″ sliver missing along bbl at rear band. Multi-groove rifling in bbl is worn but discernible. 4-31284 JS151 (2,000-4,000)

TEXAS CONFEDERATE ALTERATION OF HALL RIFLE. SN NSN. Cal. 64. The following described gun was found in Texas and is a most unusual alteration to percussion. Mr. Michel, in his notes, describes this gun as follows: “Alteration to percussion of Model 1819 Hall rifle. Breechblock marked ‘J. H. Hall / H. Ferry / U. S. / 1831’. This alteration performed by a striker inserted between the jaws of the hammer with a percussion nipple screwed into the former pan. This example was recovered in Texas and shows the effect, not uncommon, of a blowout resulting from loose powder being ignited inside the breech. Wood on the right side has been completely blown away alongside the breech and striker. Top jaw and jaw screw of hammer shorn off”. Similar examples are described, but not shown, in Murphy & Madaus. CONDITION: Gun appears in as-found condition. All metal parts are brown and pitted. Stock exhibits several breaks and missing approx. 11″ section on right side as described above allowing mechanism to be shown. Gun lacks ramrod and top jaw and striker to nipple. 4-31283 JS150 (2,000-4,000)

Revised: 10/19/2007

Correction)Barrel bore is .54 cal; breech block is .69 cal.

CONFEDERATE ALTERATION OF A HALL RIFLE. SN NSN. Cal. 64. This gun is similar to so-called “Western” alterations pictured in Murphy & Madaus; however, this hammer is more petite and better made. Mr. Michel describes this gun as follows, “Alteration to percussion of Model 1819 Hall rifle. Breechblock is marked ‘J. H. Hall / U.S. / 1839’. This alteration was performed by brazing a percussion hammer onto the orig flintlock hammer base and screwing a nipple into the area of the former pan which has been built up to support and reinforce the nipple. This type of alteration is akin to those characterized as typical ‘Western’ alteration. Missing mainspring and trigger”. An example shown with no mating numbers. You are bidding on a possibly unique Confederate-altered Hall with a very distinctive hammer. CONDITION: Metal surfaces are brown/black with numerous dings, scratches and pitting. Bore is filled with insect nests, and rifling cannot be ascertained. Stock is solid with some insect damage and hairline cracks. About a 1″ x 1-1/2″ piece of wood is missing and repaired behind frame on top of buttstock. Forestock is restored forward of middle band as is ramrod and front 2 bands. Mainspring and trigger are broken. 4-31285 JS149 (2,000-4,000)

CONFEDERATE ALTERATION OF A HALL RIFLE. SN NSN. Cal. 64. This is another interesting variation of a Confederate Hall alteration, utilizing the brazing and peening of striker to base of orig flint hammer. Old jaw screw is utilized and top is peened over the new striker. Similar alterations are shown in Murphy & Madaus, but nothing exactly like this. You are bidding on a possibly unique variation of a Confederation Hall alteration. Mr. Michel’s Notes State: “Alteration to percussion of M1819 Hall rifle. Breechblock marked “US / S. North / Midltn / Conn / 1835”. This alteration performed by peening a striker onto the bottom jaw of the original flintlock hammer and a nipple screwed into the former pan. This type of alteration is similar to but not identical to Alterations on other North contract rifles with a “S. Carolina” stamp on the left flat of the frame.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are gray/brown with scattered pitting. Ramrod and rear band are probable replacements. Stock is sound, showing numerous scrapes and scratches. Orig inspector’s cartouche is still visible on left side of stock. 4-31282 JS148 (3,000-5,000)

MISSISSIPPI CONFEDERATE ALTERATION OF A HALL RIFLE. SN NSN. Cal. 64. This is another variation of the Confederate alteration thought to be performed at either Holly Springs or Columbus, MS. The most discernible difference in these variations is size and shape of hammer. Murphy & Madaus show in Confederate Rifles and Muskets, plates 23 & 24, p. 334, a nearly identical specimen of an 1832-dated Hall that is attributed to a MS armory. This alteration, according to Murphy & Madaus, was “thought to have either occurred at the Holly Springs Armory or Columbus (Briarfield) Arsenal. As with those altered rifles, the chamber block was removed from the frame, and the flintlock battery was removed from the block. Upper and right surfaces from the block were ground to eliminate the projections from the pan, its fence, and the frizzen supports. The indentation in the upper right top of the block that permitted the toe of the frizzen to rotate, however, was not filled in. The former vent was enlarged and threaded; into the newly-threaded hold a percussion code was screwed at a 90-degree angle to the top of the block. The old flintlock cock was cut above the throat, so as to remove the jaws and jaw screw. In place of those parts a new top section incorporating a striker and spur was brazed to the lower section of the cock. The percussion hammer then was re-attached to the chamber block, and the block was re-inserted into the frame. No reassembly marks were applied to the rifles during the process of alteration”. You are bidding on a near “attic” condition Mississippi conversion of a Hall rifle. Mr. Michel’s Notes State: “Alteration to percussion of M1819 Hall rifle. Breechblock marked “J. H. Hall / H. Ferry / US / 1832”. This alteration performed by reforming the original flintlock hammer with the top configuration, that of a percussion hammer. The hammer still retains the circular opening of the original configuration. A nipple has been screwed into the breechblock from which the original pan has been fitted in and filed off. Provenance: Described and type shown, ”Confederate Rifles and Musketoons“ by John Murphy and Howard Madaus, p. 316.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are gray with old cleaning, scattered staining and pitting. Stock exhibits several hairline cracks, and a 1″ x 1-1/2″ piece of wood that is broken at base at back of frame. Multi-grooved Hall rifling is very good. 4-31281 JS147 (3,000-5,000)

AUSTRIAN LORENZ RIFLE. SN NSN. This Austrian Lorenz rifle is complete and in near “attic” condition. It comes complete with adjustable rear sight. Use of adjustable rear sight is a more scarce variant of these Austrian import rifles. Traces of orig finish on bbl around breech. It shows little use. Mr. Michel, in his notes, states: “Probably second only to British Enfields in the number of arms imported to the Confederacy was the Austrian Lorenz Model 1854 rifle. This example, with lockplate marked ‘860’ indicating a date of manufacture of 1860, is fitted with a folding leaf sight. Complete with original bayonet and tools”. You are bidding on a fine example of a popular, imported rifle of the Civil War, complete with cleaning jag, gun tool, and matching bayonet. CONDITION: Bbl is gray/brown with some areas of scattered staining and light pitting. Lock is gray and smooth. Other metal surfaces are gray/brown with scattered staining and pitting. Stock retains some orig finish with fairly sharp edges. 4″ hairline crack in buttstock does not affect aesthetics. Rifling in bore is very good, though pitted. 4-31324 JS130 (1,000-1,500)

AUSTRIAN LORENZ RIFLE. SN NSN. Cal. 54. This is a nice example of a popular Civil War import to both North and South. This rifle has 37-1/4″ bbl, fixed rear sight. This example is complete and orig, accompanied by orig bayonet, cleaning jag, and gun tool. Mr. Michel, in his notes, states: “Probably second only to British Enfields in the number of arms imported to the Confederacy was the Austrian Lorenz Model 1854 rifle. This example, with lockplate marked ‘860’, indicating a manufacturing date of 1860, is fitted with a fixed sight. Complete with original bayonet and tools.” This is a nice, complete, near “attic” condition example of a popular Confederate imported rifle. CONDITION: Metal surfaces are gray/brown with scattered pitting. Wood is very good with some small nicks and dents. Accompanying tools match nicely with patina. Rifling in bore is very distinct though pitted. 4-31325 JS129 (1,000-1,500)

SOUTH CAROLINA ENFIELD RIFLED MUSKET. SN 412. Cal. 58. There is little doubt this is the finest SC surcharged blockade run Enfield rifled musket in existence. It is also among and may be the best Blockade Run Enfield rifled musket in private hands. Musket exhibits raised grain in its stock. Retains almost all its orig blue finish on bbl. Traces of muted case colors are visible on lock. Gun is 1 of only a few with 5/8″ “SC” letters on right side of buttstock and smaller “SC” stamped on top of comb in front of buttplate. Buttplate and ramrod are both engraved with SN 412. Accompanying bayonet is maker marked “Robinson” and still retains 1/2 the orig blue finish on its socket and is serial numbered “1660”. Most Model 1853 Enfield rifled muskets have 39″ bbls, as prescribed by English regulations; however, some SC guns, such as this, have 40″ bbls, and this gun is .58 cal, as opposed to .577. We know this caliber due to the final gauging proof of “24” which translates to .580 caliber. As with most serial numbered, Blockade Run, Confederate guns, a “JS” over anchor proof is stamped behind trigger guard and buttstock. This marking on this example is especially well struck. Behind the “JS/Anchor” proof is the stock maker’s mark “Isaac Hollis & Sons”. According to Mr. Michel’s notes, this gun was orig purchased from Bannerman in the 1930s. Mr. Michel’s Notes State: “Pattern 53 Enfield rifled musket with buttstock stamped “SC” designating shipment to South Carolina. Lockplate marked, forward of hammer, “Tower / 1862” and at tail with crown. Under buttstock is stamped “Isaac Hollis & Sons” and “JS” over anchor. The buttplate tang is engraved with numbers typical of those associated with Enfields imported by the Confederacy, in this case 412. The breech is a special, octagonal, patent breech. The piece is in almost mint, unfired condition, having been purchased originally from the ????????? in the 1930s,” CONDITION: Bbl is smooth and retains 95%+ orig blue finish with light pitting at breech. Bbl muzzle is scratched from where bayonet has been attached. Lock is gray and smooth with traces of muted case color. Rifling in bore is well-defined, though pitted. Brass nose cap, trigger guard, and buttplate are smooth with scattered scratches. Stock shows raised grain on some surfaces. Several dings and gouges are scattered on stock surface. Vice mark is present on both sides of stock forward of lock. Buff leather sling that is attached is overall very good. Locking ring on bayonet is broken and missing a piece approx. 1/4″. This locking ring could easily be replaced. Bayonet socket retains about 50% of its blue finish. Bayonet has accompanying scabbard which is very good overall with a soiled buff frog. Frog is English War Dept. inspected. 4-31308 JS126 (15,000-18,000)

CONFEDERATE BLOCKADE RUN ENFIELD RIFLED MUSKET. SN 1859. Cal. 577. This is a deeply patinaed, untouched, attic or barn found Enfield. This was a standard arm of the Confederate Army. Probably more of these guns were used than any other single arm. SN 1859 engraved on buttplate. Stock is also marked with the “JS / anchor” and the letter “S” in front of buttplate SN. Lock is marked and dated “1861 / Tower”. 39″ bbl has correct Birmingham proofs, but is missing its rear sight. Accompanying gun is a nice, added buff sling and an unsurcharged Enfield bayonet. Mr. Michel’s Notes State: “Pattern 53 Enfield rifled musket. Lockplate marked forward of hammer, “Tower / 1861” and at tail. The tang of the buttplate is engraved with the inventory number “1859” used to keep track of arms shipments to the Confederacy.” PROVENANCE: Ben Michel collection. CONDITION: Iron surfaces are brown/black with pitting, especially at bbl breech. Brass nosecap, trigger guard, and buttplate are deeply patinaed. Stock is solid with scattered dings, scratches, and scrapes. Bore of bbl shows no discernible rifling. Bayonet socket is brown; blade is partially cleaned and is bent. Ramrod is heavily pitted. 4-31311 JS140 (2,000-4,000)

BLOCKADE RUN LONDON ARMORY COMPANY ENFIELD RIFLED MUSKET. SN 8450. Cal. 577. This is a standard Model 1853 Enfield rifled musket; the most popular weapon of the Confederate infantryman during the Civil War. Lock is marked “1861 / L. A. Co.” forward of hammer, and rear of hammer with a crown and “VR”. “VR” commemorated the current British monarch, Queen Victoria (Victoria Regina). Stock has about a 7/8″ cartouche which reads “London Armory Company / 1861”. SN is cut into buttplate tang. London Armory muskets are not found with a “JS / anchor” marked as are most other serial numbered Blockade Run Enfields. Accompanied by leather sling and bayonet with engraved numbers on socket, engraved vertically in 2 lines “23 / 156”. Initials “AP” are found carved on left side of buttstock, probably by the Confederate who carried this gun. Mr. Michel’s Notes State: “Patten 53 Enfield rifled musket manufactured by London Armory Co., a principal supplier of arms to the Confederacy. Lockplate marked, forward of the hammer, “1861 / L. A. Co.” and at the tail, crown over “VR”. The tang of the buttplate is engraved with the inventory number “8450” used to keep track of arms shipments to the Confederacy.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is brown with areas of pitting. Bbl flat at tang has been ground, continuing onto tang. Bbl exhibits discernible rifling, though pitted. Lock is gray with clear markings. Brass mounts are smooth with scattered dings and scrapes. Stock exhibits dings, scratches, and several small cracks. Ramrod is dark and pitted, matching condition of bbl. Bayonet socket exhibits traces of finish and blade is cleaned. 4-31310 JS141 (4,000-6,000)

STATE OF GEORGIA BLOCKADE RUN ENFIELD RIFLED MUSKET SN 3441. Cal. .577.A fine example of Model 1853 Enfield rifled musket bought by the state of GA during the Civil War. We know this gun is GA due to the large, 1″ “G” stamped into right side of stock. This gun is maker marked “Barnett / London” on lock and has correct London visual proofs on bbl. On top of stock comb in front of buttplate, there is an oval cartouche containing the letters ‘CH’ over ‘1’. This is a known Confederate viewing mark and will later be explained in text in current production on Blockade Run arms. There is also a SN stamped in bottom of buttplate, which is the accepted style of Barnett, instead of having SNs engraved. Ramrod is maker marked “Preston”. The accompanying bayonet is maker marked “Dear…” You are bidding on a very fine GA Enfield that is untouched. All markings are crisp and fine. It would be difficult to find a better GA-used Enfield. Mr. Michel’s Notes State: “Pattern 53 Enfield rifled musket with buttstock stamped “G” designating shipment to the state of Georgia. Lockplate marked, forward of hammer, “Barnett / London” and at the tail, the comb of the buttstock just forward of the buttplate tang is marked with an oval cartouche enclosing “CH / 1” with the “CH” indicating acquisition by Caleb Huse as purchasing agent for the Confederate States.” CONDITION: Gun appears in near “attic” condition. It appears all orig with exception of replaced rear sling swivel. Lock, bbl, ramrod, and bands are brown with scattered scrapes and pitting, especially at bbl breech. Bore still exhibits good rifling. Stock is sound with scattered scrapes and scratches. Proofmarks and letter “G” are well struck and quite discernible. Bayonet retains most of its orig blue finish on socket. 4-31309 JS125 (6,000-10,000)

CONFEDERATE BLOCKADE RUN ENFIELD RIFLE. SN 269. Cal. 577. This iron mounted Model 1856 rifle has 33″ bbl with correct Birmingham proofs and saber bayonet lug. Lock is marked and dated “Tower / 1861”. SN is cut into ramrod and stamped on bottom of buttstock, as is proper in iron mounted guns. In front of SN on buttstock is stamped “Joseph Wilson” and a crisp, clear “JS” / anchor marking is found adjacent. This is a fine and rarely encountered Blockade Run Model 1856 rifle. This gun is all orig and authentic as found. Mr. Michel, in his notes, states, “Confederate import Enfield rifle in superb condition. Stamped on underside of butt ‘269 / Joseph Wilson / JS / anchor’. The ramrod is also engraved with ‘269’. Overall the rifle appears almost unfired. The numbers indicate that this rifle was destined to arm the Confederacy, but considering its seemingly unused condition, it was likely seized as it was being run through the blockade and never issued. Ex-Raplh Arnold coll”. This is no doubt one of the very finest guns of this pattern, and probably fewer than 10 examples are known. CONDITION: Bbl is gray/bright with scattered areas of pitting. Rifling in bore is very good with pitting. Other metal surfaces are gray with scattered pitting. Stock is very good with very good, crisp markings and scattered scrapes and scratches. 4-31317 JS138 (6,000-9,000)

CONFEDERATE BLOCKADE RUN ENFIELD RIFLE. SN 2983. Cal. 577. This unusual rifle is pretty much a standard Model 1856 Enfield rifle with 33″ bbl; however, a brass patchbox has been professionally added during the war. We know this is a wartime addition because this patchbox is engraved “Plucked from the enemy”. Gun is “JS / anchor” marked. Lock is marked “1861 / Tower” and bbl has appropriate Birmingham proofs. Mr. Michel’s Notes State: “Pattern 56 Enfield Rifle. Lockplate marked forward of hammer “1861 / Tower” and at tail, The Confederate inventory number “2983” is engraved in the tang of the buttplate, and the “JS” / anchor stamp appears on the underside of the buttstock to the rear of the triggerguard plate. A brass patchbox has been added, on which has been somewhat crudely scratch engraved, “Plucked from the Enemy”.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is gray with scattered pitting and staining. Lock is dark with pitting as his hammer and bands. Brass nosecap, trigger guard, and patchbox are all cleaned and smooth. Buttplate has numerous nicks and scratches. Rifling in bore is very good, though pitted. Rear sight is missing. Sling swivels, ramrod, and at least 1 buttplate screw are replaced. 4-31316 JS144 (2,000-4,000)

CONFEDERATE BLOCKADE RUN ENFIELD RIFLE. SN 12. Cal. 577. This “attic” condition rifle has seen hard use. It is missing rear sight, 1 lock screw, and stock is broken and repaired. This gun exhibits heavy, red/brown patina on brass nosecap, trigger guard, and buttplate. Buttplate is serial numbered “12” with engraved numbers, as is ramrod. Bbl is dark and brown, deeply pitted, and ground around breech, showing no discernible proofs. Stamped in stock is maker’s mark “Bentley & Playfair, Birmingham”. Also stamped in bottom of stock next to trigger guard, but not as discernible, is the “JS” / anchor markings. Trigger guard is missing sling swivel. Inside trigger guard is written in white paint “1950”, possibly the date this gun was bought or found. Despite missing parts and damage, this is still an attractive gun with an extremely low, 2-digit serial number, and 33″ Model 1856 brass-mounted rifles are scarce. Mr. Michel’s Notes State: “Pattern 56 Enfield rifle. Lockplate marked forward of the hammer “1861 / Tower” and at tail. The Confederate inventory number “12” is engraved on the buttplate tang.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is brown/black with pitting, tool marks and grind marks around breech. Lock, band, and ramrod are brown with scattered pitting. Brass has heavy patina. Stock is sound with exception of old break above wrist which has old, glued repair. A piece of wood about 2″ x 1/2″ is missing from stock opposite lock, along with screw and its escutcheon. About a 2″ crack is present in buttstock. Rear sight and rear sling swivel are missing. 4-31315 JS139 (2,000-4,000)

CONFEDERATE BLOCKADE RUN ENFIELD ARTILLERY CARBINE. SN 409. Cal. 577. This is a rarely found, Confederate imported Model 1858 artillery carbine or musketoon. It is “JS / anchor” marked on bottom of stock with stock maker “James Webley”. SN on buttplate engraved longitudinally and letter “S” is stamped in front of buttplate tang. Lock is marked and dated “1861 / Tower”. Bbl has correct Birmingham inspection proofs. This is a very nice, sound gun overall and would be difficult to upgrade. Mr. Michel’s Notes State: “Pattern 58 artillery carbine (or musketoon). Lockplate marked, forward of hammer, “1861 / Tower” and at tail with crown. The piece has both the Confederate inspector’s stamp under the buttstock just to the rear of the trigger guard plate consisting of a “JS” surrounding an anchor and the Confederate inventory number 409 engraved on the tang of the buttplate.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is brown with good markings with pitting around breech. Bayonet lug is sharp, as are front and rear sights. Rifling in bore is very good. Lock and hammer are smooth and gray/brown, as are bands. Ramrod is cleaned and is gray/white overall. 4-31313 JS142 (5,000-7,000)

CAPTURED ENFIELD SADDLE RING CARBINE. SN NSN. Ca. 577. This 1863-dated carbine is in very good, untouched, “attic” condition, being orig and complete. Gun exhibits Birmingham Small Arms trademark stamped in a 3/4″ rnd cartouche. Correct Birmingham proofs are stamped in bbl at breech. Lock is marked “1863 / Tower”. Stock maker’s name is stamped in bottom of buttstock, but is no longer discernible. What are thought to be Confederate inspection or acceptance marks of an anchor over an “S” is stamped on top of buttstock comb, adjacent to buttplate. Faintly scratched on left side of buttstock can be read, “Captured Oct 21 . . . at . . . by . . . “. With a magnifying glass and a little imagination, someone can probably ascertain the rest of this faint but present inscription. Mr. Michel’s Notes State: “Pattern 56 Enfield cavalry carbine. Lockplate marked, forward of hammer, “1863 / Tower” and at rear there is a small “Birmingham Small Arms Trade” stamp in the right side of the buttstock. The left side of the buttstock is a faint and largely illegible capture description.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are gray/brown with scattered pitting. Rifling in bbl is very good, though pitted. Brass trigger guard, nosecap, and buttplate are smooth with scattered nicks and scratches. Stock is sound with good markings and scattered scrapes, gouges, and scratches. Stock still exhibits a portion of its orig varnish. 4-31312 JS143 (2,000-4,000)

CAPTURED CONFEDERATE-USED ENFIELD SEA SERVICE MUSKET. SN NSN. Cal. Approx. 75. 30″ smooth bore bbl with numerous British proofs, including bbl condemnation marks of nose-to-nose broad arrows. Bbl is broad arrow proofed and dated “1854 / Enfield”. This gun, obsolete in England by the time of the Civil War, is one of the first British Blockade run guns that saw Confederate service. Attached to this gun was old tag which reads, “This rifle was taken from Fort Jackson, La. a few days after its surrender with the permission of Commander D. D. Porter by Robert T. Edes , Asst. Surg. U.S.N. of the Second Division of the Mortar Flotilla; / Lieut. Comd’r R. R. Breese”. This is a rare relic of one of the early battles of the war in the pursuit of New Orleans. This gun appears in near “attic” condition, orig and complete in every regard. Mr. Michel’s Notes State: “Pattern sea service musket. Lockplate marked forward of hammer, “1854 / Enfield” and at tail, crown / “VR”. With the musket is an old paper label reading “This rifle was taken from Fort Jackson, La a few days after its surrender with the permission of Commander D. D. Porter. Robert T. Edes Ass. Surg. USN of the Second Division of the Mortar Flotilla Lieut Comdr RR Reese”.” PROVENANCE: Ben Michel collection. CONDITION: Metal surfaces are brown with scattered staining and pitting. Bore is smooth and pitted. Brass mounts are smooth and cleaned. Stock is sound with clear markings, several small chips, cracks, and scattered stains. Front sling swivel is correct type and style; however, it may be replaced. 4-31319 JS137 (3,000-5,000)

CONFEDERATE ALTERATION OF VIRGINIA MANUFACTORY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Virginia Manufactory musket. Lockplate of musket marked at tail ‘Richmond 1803’. Bbl marked at breech with county designation ‘Nansemond’. This type of alteration with large, three faceted bolster is believed to have been done by Francis Persignon of Richmond between October 1861 and September 1862. All components are marked with orig assembly number ‘5’. Alteration re-assembly, markings are a combination of letters and Roman numerals such as on this musket, ‘MXII'”. This gun, once in the collection of Giles Cromwell, is illustrated in Bulletin No. 52 of the American Society of Arms Collectors on p. 38. It is also pictured and described in Murphy & Madaus’ Confederate Rifles and Muskets on pp. 567-569. You are bidding on a fine, all orig and complete Confederate-altered 1805-dated VA Manufactory musket pictured in several publications. A better gun would be difficult to obtain. CONDITION: Metal surfaces are smooth and brown with scattered pitting, especially at bolster. All metal parts, including trigger guard, trigger guard base, sideplate, bbl, buttplate, all 3 bands, and bayonet lug, are assembly numbered “5”. 1″ of bbl tang, behind tang screw, is missing. Stock is sound with some varnish remaining. Normal nicks, scrapes, and gouges are present on stock. Large set of initials are scratched on side of buttstock. Gun retains both orig sling swivels. Accompanying bayonet is cleaned, stained, and pitted but fits gun nicely. 4-31276 JS208 (3,000-5,000)

CONFEDERATE ALTERATION OF VIRGINIA MANUFACTORY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Virginia Manufactory musket. Lockplate of musket marked forward of hammer ‘Virginia Manufactory’ and at tail ‘Richmond 1815’. Alteration by the Union Manufacturing Co. of Richmond. Bolster of muskets altered by Union Manufacturing Co. is rounded at bottom and frequently shows round trace of brazed screw filling the hole drilled through to the vent hole. Lockplate is filed to conform to rounded contour of bolster. Re-assembly marks are generally the letter ‘U’ and a number, or just a number, in this case ‘6’. Mainspring is missing”. CONDITION: Bbl is brown and smooth with pitting. Lock is smooth, brown with good markings. Buttplate and trigger guard are brown with pitting. Assembly number “4” occurs on buttplate, sideplate, trigger guard, and bbl. Bands are not assembly marked and are replaced. Stock forward of rear band is restored. Remainder of stock is solid with scattered dings, cracks, scratches, and gouges. 4-31274 JS207 (3,000-5,000)

CONFEDERATE ALTERATION OF VIRGINIA MANUFACTORY ARTILLERY MUSKETOON. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Virginia Manufactory artillery musketoon. Lockplate of musket marked forward of hammer ‘Virginia Manufactory’ and at tail ‘Richmond 1818’. All components marked with orig assembly number ‘6’. Alteration by Thomas J. Adams in Richmond with three faceted bolster and re-assembly Roman numeral groups on inner face of new percussion hammer, inner face of lockplate, underside of bbl, and left side of stock opposite lockplate”. VA Manufactory artillery musketoons are scarce enough in flint, much less with a Confederate alteration to percussion. This particular gun is illustrated and described on pp. 31-32 of Murphy & Madaus’ Confederate Rifles and Muskets. This gun is orig and complete, and it would be hard to find another specimen. CONDITION: Metal surfaces cleaned, gray and pitted. Assembly number “6” appears on bands, sideplate, trigger guard. This number is not discernible on exterior of buttplate; however, buttplate is certainly orig to this gun with matching metal surfaces to rest of gun. Stock is good and sound, with scattered scratches, nicks, and dings. Stock has old repair on wood opposite lock. 4-31275 JS206 (3,000-5,000)

CONFEDERATE ALTERATION OF VIRGINIA MANUFACTORY MUSKET. SN NSN. Cal. 69. This gun, once in the collection of Giles Cromwell, is illustrated in his article in the American Society of Arms Collectors Bulletin No. 52 on p. 34. Mr. Michel describes this gun as follows: “Cone-in-bbl alteration to percussion of Virginia Manufactory musket. Lockplate of musket marked forward of hammer ‘Virginia Manufactory’ and at tail ‘Richmond 1811’. Rear bbl band also dated ‘1811’. All components are marked with orig assembly number ’77’. Confederate alterations by the cone-in-bbl method are very rarely encountered. This type alteration has been tentatively attributed to John B. Barret & Co. in Wytheville, Virginia”. CONDITION: This gun appears orig and matching in every regard. Assembly number “77” appears on all metal parts, including bands, trigger guard, buttplate, sideplate, and bbl. 4-31277 JS209 (3,000-5,000)

CONFEDERATE ALTERATION OF VIRGINIA MANUFACTORY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Virginia Manufactory Musket. Lockplate of musket marked at tail ‘Richmond 1804’. Bbl marked at breech with county designation ‘Hanover’. This type alteration with two faceted bolster was done by S. C. Robinson. All components marked with orig assembly number ‘4’. S. C. Robinson re-assembly markings are pairs of Arabic numerals or Roman numerals, in this case ’20 / 8′. With bayonet numbered ‘7’”. You are bidding on a fine, Confederate converted, Virginia Manufactory musket with all matching assembly numbers that includes a VA Manufactory angular bayonet with similar assembly number. Bayonet is SN 7 whereas the rest of the gun has assembly number 4. This gun was once in the collection of Giles Cromwell and is described in Murphy & Madaus’ Confederate Rifles and Muskets on p. 624. CONDITION: Bbl is brown/black with pitting, especially at bolster. County regimental markings on bbl flat are partially discernible, as “Hanover” can be read. Other metal parts are brown with pitting and are all assembly stamped “4”. Ramrod appears to be a Confederate, blacksmith-forged addition. Stock is sound and solid with scattered dings, gouges, and scratches, and a hairline crack forward of lock. Initials “WWS” are stamped in buttstock. About 2″ of wood behind bolster is repaired. Accompanying bayonet with assembly number “7” is is cleaned and has pitting. 4-31278 JS210 (3,000-5,000)

CONFEDERATE ALTERATION OF FRENCH MODEL 1777 COLONIAL & MARINE MUSKET. SN NSN. Cal. 69. Murphy & Madaus, in their book, Confederate Rifles and Musketoons, show a nearly identical musket converted in Richmond on p. 33, which was converted by T. J. Adams of Richmond, VA, and that gun is currently at the Rush Hawkins Memorial. It is amazing to think that muskets originally used in Colonial America and possibly the War of 1812 could be reused during the American Civil War. This gun, like gun at Rush Hawkins Memorial, is regimentally marked to a City of Richmond regiment, though markings have been mostly obscured during alteration. Mr. Michel describes his gun as follows: “These muskets were originally made at the Tulle Armory in France for VA in 1786-87. Lockplate is marked forward of the hammer ‘Tulle’. Configuration of the musket is consistent with French pattern with brass buttplate, trigger guard, sideplate, and front and rear bands. Middle band with sling swivel is correctly made of iron. Alteration to percussion was done by S. C. Robinson & Co. of Richmond, VA using its characteristic two facet brazed bolster. Top of the barrel shows remnants of the city marking, ‘Richmond’.” You are bidding on a gun about 220 years old that remarkably probably saw use in the War of 1812 and Civil War for Virginia troops from the city of Richmond. CONDITION: Iron surfaces are gray with scattered pitting. Brass surfaces, including bands, trigger guard, and buttplate are smooth and patinaed with scattered scratches. Stock is sound with numerous scratches, nicks, and gouges. There is about a 3/4″ gap where wood is broken out behind lock. 4-31263 JS192 (3,000-5,000)

CONFEDERATE ALTERATION OF BROWN BESS MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Alteration to percussion of 3rd Model Brown Bess British musket. While the alteration is by use of a drum rather than the characteristic brazed bolster, the alteration is clearly intended for military usage with a large military nipple and hammer of M1842 type. This musket is typical of many altered in the South by small gunsmiths or entrepreneurs. Recovered outside Richmond, VA, it has been left in rusty ‘untouched barn mint’ as proof of its all orig character.” You are bidding on a possibly unique Confederate-altered Brown Bess musket in untouched, “attic” or “barn” condition. CONDITION: Bbl, lock, and hammer are brown and heavily pitted. Ramrod is brown, smooth, and pitted. Brass buttplate, trigger guard, and ramrod pipes are all heavily patinaed. Scattered drips of paint are found on various parts of gun. Stock is missing nosecap, but otherwise is sound and complete, with scattered nicks, cracks, and gouges. 4-31264 JS191 (3,000-5,000)

CONFEDERATE ALTERATION OF STATE OF VIRGINIA SWAN CONTRACT MUSKET. SN NSN. Cal. 69. This rare Swan contract musket is beautifully marked with its Dinwiddie regimental markings and is illustrated and described on pp. 164-165 of Murphy & Madaus’ Confederate Rifles and Muskets. Mr. Michel describes this gun as follows: “This musket is one of the 7,831 imported muskets delivered to VA by contractor James Swan of Boston during the period from 1797 to 1801. The cone in bbl alteration to percussion is the method of A. G. Dabney at the Phoenix Foundry in Lynchburg, VA. Bbl is marked ‘Va REGt DINWIDDIE’. Configuration of the musket is consistent with those delivered by Swan to VA, being British Brown Bess in outline, albeit somewhat crudely made by comparison. Forend of this piece has been restored.” CONDITION: Bbl is brown and pitted, as is lock. Bbl markings are quite distinct. Stock is restored starting about 3″ forward of lock, forestock is totally restored, as are ramrod pipes, ramrod, and nosecap. Brass buttplate and trigger guard exhibit good patina. Buttstock exhibits scratches, nicks, and scuffs, and a couple small repairs forward of lock. 4-31261 JS194 (3,000-5,000)

CONFEDERATE ALTERATION OF STATE OF VIRGINIA SWAN CONTRACT MUSKET. SN NSN. Cal. 69. This gun is illustrated and described in Murphy & Madaus’ book Confederate Rifles and Muskets on pp. 625-627. Mr. Michel describes this gun as follows: “This musket is one of 7,831 imported muskets delivered to Virginia by contractor James Swan of Boston during the period from 1797 to 1801. Brazed bolster alteration to percussion was done by S. C. Robinson of Richmond using the characteristic two faceted bolster. Bbl regimental markings ‘ORANGE’ are visible though indistinct. Virginia regimental marking is indistinct. All orig throughout.” CONDITION: Bbl and lock are gray/brown with pitting. Brass nosecap, ramrod thimbles, trigger guard, and buttplate are all cleaned with scattered scratches and patina in protected areas. Ramrod is replaced. Last 10″ of stock toward muzzle is restored. Stock otherwise is sound and solid with a 3″ repair of bottom of forestock forward of hammer. County bbl markings are weak but “Orange” is discernible. 4-31262 JS193 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1817 U.S. RIFLE. SN NSN. Cal. 54. Mr. Michel describes this gun as follows: “Alteration to percussion of Model 1817 made by N. Starr & Co. Lockplate marked forward of hammer ‘N. Starr & Co’ in arch over ‘US’ and at tail, ‘Middtn / Conn / 1843′. In addition to the alteration to percussion, the forestock has been altered by removing the middle band, creating the appearance of a two-band rifle and in addition insetting a saber bayonet lug with guide key onto the barrel. Brazed bolster of unique design with a vertical rear and horizontal bottom is believed to be the work of William B. and Cyrus Fisher of Lynchburg, Virginia. Ex-James Artimus collection.” This Confederate percussion alteration is pictured and described on pp. 227-230 in Murphy & Madaus’ Confederate Rifles and Muskets. This gun is in fine, untouched condition with a fine, rifled bore and orig finish on much of the gun. This is a most unusual conversion. Not only was ignition system changed from flint to percussion, the overall gun was “modernized” by relocating the front band sufficiently far back such that the middle band could be eliminated and a brazed saber bayonet lug was attached for use of saber bayonet. You are bidding on a superb condition, possibly unique restoration by Lynchburg, Virginia gunsmiths that is completely orig, authentic, and complete. CONDITION: Bbl is smooth and brown with some orig brown finish. Slight rust and pitting at bolster. Bbl markings are very clear. Lock was cleaned, probably during conversion. Lock retains good surfaces, but orig U.S. markings are weak and partially obscured. Other metal components including trigger guard and buttplate are smooth with some orig finish. Rear band is uncleaned, gray, with traces of finish. Front band has a mottled, cast appearance. Small “2” is stamped in face of front band and also on bayonet lug, which was added during alteration. Accompanying ramrod is brass-tipped Mississippi. It is gray and pitted. Stock is very good, showing orig varnish, scattered dings and scratches, and residual cartouches from orig flint inspection. Patchbox contains extra nipple, cleaning jag, worm, and nipple wrench/screwdriver combination tool. Rifling and bore are very good. 4-31302 JS189 (4,000-8,000)

CONFEDERATE ALTERATION OF MODEL 1803 HARPERS FERRY RIFLE. SN NSN. Cal. 54. Mr. Michel describes this rifle as follows: “This alteration involved both the alteration of the flintlock to percussion and the reconfiguration of the stock to that of a two-band rifle. Retaining the orig rifle configuration to the buttstock, the forend with its under bbl rib has been replaced with a rear brass single band (both M1841 rifle in type) connected with a new wooden forestock. In addition, the orig rifle style trigger guard has been replaced with a M1841 trigger guard plate and trigger guard bow, as well as the trigger itself. The brazed bolster alteration to percussion is also unique as yet not identified as to the maker. A similar bolster does appear to have been used to alter M1817 rifles (see consignment nos. 4-31302 and 4-31303) and a Whitney Model 1812 (see consignment no. 4-31270). It is believed that these alterations may be the work of William B. and Cyrus Fisher of Lynchburg, Virginia.” You are bidding on a rare, brass-mounted, Confederate alteration of a Harpers Ferry rifle, probably altered by William and Cyrus Fisher of Lynchburg, Virginia. Gun is very solid overall. Stock is sound with no repairs. The gun must have gotten a little wet at some point, as metal surfaces are pitted, whereas the brass is nice. Bbl still exhibits nice rifling. This rare alteration is similar to Consignment No. 4-31302, which is a similar conversion rifle. CONDITION: Bbl and lock are brown with some cleaning and heavy pitting. Brass bands, trigger guard, buttplate, and patchbox have scattered dents, scratches, and varying patination. Tulip-tipped ramrod is brown with scattered pitting. Stock is solid. Several chips, some small splinters are missing along ramrod channel. About a 3/4″ chip is missing from toe of stock. 4-31301 JS190 (3,000-6,000)

CONFEDERATE ALTERATION OF MODEL 1817 U.S. RIFLE. SN NSN. Cal. 54. Mr. Michel describes this rifle as follows: “Alteration to percussion of Model 1817 rifle made by S. North. Lockplate marked forward of hammer ‘US / S. North’ and at tail ‘MIDDLtn / CONN / 1829’. Other than the alteration to percussion, this rifle has not been modified as has the M1817 rifle reconfigured to two-band with a saber bayonet lug added (see consignment number 4-31302) which has same unique bolster alterations. These alterations are believed to have been made by William B. and Cyrus Fisher of Lynchburg, Virginia.” You are bidding on a very rarely offered alteration believed to have been done by Fisher of Lynchburg, Virginia. CONDITION: Bbl is cleaned and re-browned, as is buttplate. Lock and hammer are cleaned. Bands are mismatched, but all of correct type. Ramrod is originally from a Mississippi rifle. Patchbox hinge screws are replaced, as are screws in trigger guard. Bbl and lock are pitted overall. Rear sight is restored as is nipple. Bore exhibits no rifling. Stock is sound and solid with scattered scratches and small dings. A 1-1/2″ crack is exhibited in toe. Orig inspector’s cartouche is still visible. 4-31303 JS188 (3,000-6,000)

CONFEDERATE ALTERATION OF MODEL 1812 WHITNEY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Alteration to percussion of Model 1812 Whitney musket. Lockplate marked forward of hammer ‘N. Haven’ in scroll. Alteration is with brazed bolster of unique configuration, vertical in rear and horizontal at bottom, which is believed to be the work of William B. and Cyrus Fisher of Lynchburg, Virginia. This distinctive shaped bolster and equally distinctively shaped hammer all appear together on the alteration of a Model 1803 (Consignment No. 4-31301) and a Model 1817 rifle”. You are bidding on a fine, complete, rare William & Cyrus Fisher, Lynchburg, VA alteration. There probably cannot be a better example known. CONDITION: Bbl is cleaned with scattered staining and pitting. Orig flint bbl proof “P” is well-defined. Lockplate is gray with New Haven markings partially removed. Matching bands and the trigger guard are brown, smooth, and stained. Ramrod and buttplate are gray/bright with scattered staining and pitting. Stock is solid and sound with some orig finish. Residual cartouche and various assembly stampings in wood are crisp. Stock exhibits numerous dents, nicks, scrapes, and scratches. Gun retains both orig sling swivels. 4-31270 JS203 (3,000-5,000)

IDENTIFIED 21ST VIRGINIA (STONEWALL BRIGADE) CARRIED CONVERSION MUSKET. SN NSN. Cal. 69. Mr. Michel describes this musket as follows: “A Model 1816 musket altered to percussion by Colt, this piece eventually found its way into the hands of William Exall of the 21st Virginia Infantry. His name ‘W. Exall’ appears carved into the right side of the butt of the musket and ’21st Va’ and ‘Co F’ are carved into the left side of the butt. With the musket is a handwritten note dated September 12, 1936 which reads, ‘My Dear Doctor, Mrs Foley of the Richmond Civil War Records Office states that there were two Exalls in the 21st Virginia Regt., one Charles and a William. The latter enlisted April 21, 1862, in Richmond and was killed at Bath, Jan 3rd, 1863. I concluded after reading her testimonial that the inscription on your musket indicates that your musket after examining it with the utmost scrutiny have determined that weapon was indeed used by William Exall, Late of the Stonewall Brigade. Your contribution of this relic to the museum would be most gratifying. My Deepest and heartfelt thanks. Felix Gross’. Also with the musket is a separate card indicating that the musket and note were purchased at auction of a private home in Gordonsville, Virginia. This musket is one altered by Colt for Russia in 1855-56 but which Colt ended up selling to Italy in 1860 after Russia abrogated the contract. These arms were then seized by English authorities while en route. Undoubtedly then sold to Confederate agents looking to purchase arms in England, the musket afterward returned to America and ultimately into the hands of William Exall.” You are bidding on a musket used by a Virginia soldier killed early in 1863 who was a member of the famed Stonewall Brigade along with an accompanying note dated 1936 relating its incredible history. CONDITION: Bbl, lock, trigger guard, and buttplate are cleaned and heavily pitted. Rear band is dark and pitted. Front bands are cleaned smooth and stained. Front band lacks locking spring. Ramrod is of correct style, but shortened about 10″. Stock contains numerous scratches, dings, and stains and has been lightly sanded. Buttstock has repaired crack at toe. Scratched ID in stock is possibly commemorative, as it appears carved after stock was orig cleaned. 4-31273 JS187 (10,000-30,000)

CONFEDERATE ALTERATION OF MODEL 1812 SPRINGFIELD MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Model 1812 Springfield musket with ‘Wickham improvement’ stud retained bands. Lockplate marked forward of hammer, eagle / ‘Springfield’, and at tail ‘1815’. Altered by Union Manufacturing Company of Richmond with typical rounded bottom bolster and lockplate filed to conform to reounded contour. Reassembly number ’17’ on inside of percussion hammer. With bayonet”. CONDITION: Metal surfaces cleaned overall with scattered pitting. Lock markings are discernible, as are bbl proofs. Stock is cleaned. Scattered scratches, nicks. Accompanying bayonet is surcharged and inspected US and is very good overall. 4-31279 JS199 (3,000-5,000)

MONROE BLUES ALTERATION MUSKET. SN NSN. Cal. 69. Several states, both North and South, had a “Monroe Blues” as a company designation. A little detective work could potentially solve this mystery, as this gun also has an inset star with “3rd” engraved on it, so if there is a 3rd Regiment with a company name “Monroe Blues,” you would probably have a match. This gun potentially was to be used as a shooting prize, and maybe was a prize, but never inscribed to a recipient. Presentation plaque on reverse of buttstock simply reads “Presented by / The Monroe Blues / To” leaving a blank space for a name. Mr. Michel describes this gun as follows: “This alteration to percussion of a Model 1840 Nippes contract musket is actually a re-alteration of a Nippes/Maynard primer musket alteration as evidence by the plugged hole to the rear of the drum bolster. That hole was orig for the primer box (now removed) attachment screw. On the left side of the butt a brass eagle over banner plate has been inlet and pinned to the stock. There is light engraving of the eagle’s feathers and eye, but the banner is unengraved. A brass star has been inlet into the top of teh wrist of the stock to the rear of the breechplug tang. The star is engraved ‘3rd’. A silver plaque has been inlet and pinned into the left side of the buttstock. It is engraved ‘Presenteed by the Monroe Blues to’ but no name has been engraved as well”. CONDITION: Metal surfaces all cleaned with scattered pitting. Accompanying bayonet is surcharged U.S. Overall good condition and fits gun well. Stock is sound and cleaned with scattered nicks and scratches. 4-31280 JS195 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 NATHAN STARR MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Brazed bolster alteration to percussion of Model 1816 N. Starr. Lockplate of this musket is marked forward of the hammer ‘US / N STARR’ and at the tail ‘MIDELTN / CONN / 1829 / *’. This alteration is typical of that done by Union Manufacturing Co. of Richmond. Round bottom bolster is fitted to lockplate which has been filed to conform to the rounded contour of the bolster. Inside of percussion hammer is numbered ’51’. With bayonet”. PROVENANCE: Ben Michel collection CONDITION: Metal surfaces are cleaned gray/brown with scattered pitting. Lock & bbl markings are well easily read. Accompanying bayonet is US surcharged and inspected and is in overall good condition. 4-31473 JS197 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 HARPERS FERRY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Brazed bolster alteration to percussion of Model 1816 Harpers Ferry musket. Lockplate of musket marked forward of hammer with eagle / ‘US’, and at tail ‘Harpers Ferry 1823’. Brazed bolster is rounded at bottom with brass pan remnant filed to conform to rounded contour of bolster. Alteration resembles rounded shape of Union Manufacturing Co., except for a notch where the curve of bolster meets lockplate. Orig assembly number on parts is ‘4’. Alteration reassembly number is a small ‘5’ which appears on the inside of new percussion hammer, breechplug tang, and bbl. With bayonet”. CONDITION: Metal surfaces are brown/gray with scattered pitting. Ramrod is cleaned but is orig. Accompanying bayonet is brown with US surcharge and in overall good condition. Stock is sound with numerous scratches and nicks. Buttstock is scratched with soldier’s intitials “HL / Co. D”. 4-31272 JS196 (3,000-5,000)

CONFEDERATE ALTERATION OF A MODEL 1816 B. EVANS/PHILADELPHIA MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Model 1816 Evans/Philadelphia musket. Lockplate of musket marked forward of hammer ‘B. Evans’ in upward curve over ‘Phila’. Note: this musket is rare even in its unaltered state. Reilly, in United States Martial Flintlocks on p. 101 notes only a single specimen with this marking is known to the author. This alteration is typical of that done by Union Manufacturing Co. of Richmond, Virginia. Round bottom bolster is fitted to lockplate which has been filed to conform to its rounded contour. Inside of percussion hammer is marked with typical ‘U’ over re-assembly number, in this instance ‘309’. ‘309’ also appears stamped inside lockplate. Mainspring is missing. With bayonet”. CONDITION: Metal surfaces cleaned and are gray/brown with pitting. Stock is sound with scratches, nicks, and gouges and old varnish. Accompanying bayonet is US surcharged and inspected and is very good overall. Middle band is stamped “213”. Other two bands are not numbered. 4-31269 JS202 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 HARPERS FERRY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Model 1816 Harpers Ferry musket. Lockplate is marked forward of the hammer with an eagle over ‘US’ and at the tail ‘Harpers Ferry 1829’. Alteration with its two faceted bolster with a flat bottom resembles those performed by S. C. Robinson of Richmond, but narrow, unmarked hammer and crude fitting of the bolster atop the cut off pan is unlike the quality of Robinson alterations. Most likely this is simply one of the many alterations performed by any number of gunsmiths in the Confederacy to meet the exigencies of the war”. You are bidding on an “attic” condition, untouched, all orig and complete, classic, Confederate, brazed bolster alteration with a very distinctive hammer showing typical hand-forged manufacture of Southern blacksmith. CONDITION: All metal surfaces are brown with pitting. Stock is sound and solid with scattered scrapes, nicks, and gouges. Cartouches are still visible from when gun was inspected in flint. 4-31271 JS201 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 POMEROY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Confederate alteration of Model 1816 Pomeroy. Alteration by brazing a raised platform on right side of breech of bbl for insertion of nipple (a reinforced ‘cone in bbl’ alteration). Cut off outside surface of pan is stamped with number ’37’. This number is also stamped inside hammer. Lockplate marked forward of hammer with eagle over ‘US’ and at tail, ‘1818’”. You are bidding on an “attic” condition, Confederate alteration of unknown manufacture which is nicely preserved. CONDITION: Metal surfaces with exception of replaced ramrod are brown, uncleaned with staining and pitting. Stock is solid with numerous scratches, dents, and dings. Hairline crack is found opposite lock. About 1″ x 1/2″ piece of wood is missing from ramrod channel. 4-31266 JS205 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 POMEROY MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Alteration to percussion of Model 1816 L. Pomeroy musket. Lockplate marked forwward of hammer, eagle over ‘L. Pomeroy’ and at tail ‘1824 / U.S.’. Curved bottom brazed bolster performed by Daniel C. Hodgkins & Sons of Macon, GA. This same Hodgkins pattern alteration appears on longarms as early as 1795 pattern Springfields to Model 1817 rifles. Although records indicate that Hodgkins altered thousands of such weapons, surviving examples are quite rarely encountered”. CONDITION: All metal parts are cleaned with scattered pitting with exception of ramrod, which is replaced. Lock markings are crisp and discernible. Bbl tang exhibits matching date to that on lock. Stock is sound and solid, exhibiting residual cartouche, scattered scratches, scrapes, dings, and gouges. 4-31265 JS204 (3,000-5,000)

CONFEDERATE ALTERATION OF MODEL 1816 B. EVANS/VALLEY FORGE MUSKET. SN NSN. Cal. 69. Mr. Michel describes this gun as follows: “Bolster alteration to percussion of Model 1816 Evans/Valley Forge musket. Lockplate of musket marked forward of hammer ‘B. Evans and Valley Forge’ in oval surrounding an eagle, and ‘1824’ at tail. Alteration by S. C. Robinson of Richmond with typical two facet bolster. Condition of musket is lacking (old wrist break screw repaired and forend from middle band to front band has been replaced along with replacement bands) but this alteration is very rare on this type contract musket”. CONDITION: Bbl, trigger guard, buttplate, and front band appear untouched and brown with pitting. Stock forward of rear band is restored, as are front bands. Stock otherwise is sound with old repair just above wrist, done with 2 large wood screws. Bbl and lock markings are discernible but weak. 4-31268 JS200 (3,000-5,000)

FINE “ARSENAL TYPE” CONFEDERATE BOWIE KNIFE AND EXCEPTIONAL ORIGINAL SCABBARD. One of the finest arsenal made Confederate fighting knives to come to market in recent times. Of classical style and massive size, this original Bowie type knife retains its original leather scabbard in outstanding condition. The knife measures 23 ½ “overall with the blade being single edged with a lightly clipped point which is 1 ½” wide at the ricasso. The “D” guard is mad from a single wide strap of iron with a convex face and flat interior terminating at the pommel with a simply rounded end and with a pointed simple quillon. The grip is of plain, undecorated walnut carved in bulbous form with an iron ferrule at the base. Accompanying this wonderful and massive Confederate knife is its original scabbard. I’ve seldom encountered a confederate knife scabbard in such condition. The scabbard is fashioned of black bridle leather with a single line tooled decoration at the throat. The scabbard is sewn up the back and folded and sewn on top where the drag is applied. In addition, the scabbard is secured by three (only two remain) small lead rivets. The drag is of soldered tin, secured by two iron pins. A small horizontal loop is cut from the face of the scabbard near the throat and sewn on the reverse is a single leather belt loop-affixed in slanted fashion. Many confederate style “D” guard knives are on the market. Seldom do we encounter one of this size in arsenal style with such classical characteristics as to make its manufacture and use in the Confederacy unquestionable. Mr. Michel’s Notes State: “An arsenal-made, D-guard Bowie knife in its original scabbard. The knife is well made and the blade untouched having only age staining. The hilt and scabbard are also in the same fine, untouched condition. The scabbard is hand sewn at the bottom edge which is reinforced by three lead rivets, one of which is now missing. The tip is made of sheet tin. On the reverse of the scabbard is a single, long, diagonally placed belt loop. Overall, this is one of the finest examples of this classic style of D-guard Bowie.” These bayonets are most likely the product of the Georgia Armory, Milledgeville, GA. CONDITION: : Excellent. The knife is in excellent condition, tight all the way around. The blade is about 50% bright and 50% mottled dark grey. No major pitting has occurred. The black iron “D” guard show light surface rust but retains a wonderful untouched patina. The grip is fine. The exceptional leather scabbard is also in excellent condition with only the most minor surface crackling and age. One of the lead rivets is missing and one of the iron pins that secure the drag is missing. It fits the knife like a glove except for some minor shrinkage in length. 4-31398 JS0 (6,000-8,000)

GEORGIA MADE CONFEDERATE BOWIE KNIFE. This knife has many characteristics of the Etowah Iron Works made Bowie knives by Mark Cooper. The turned wood handle, brass crossguard, ferules, and pommel are so typical of his knives, and we believe this to be one. According to Cooper’s records, about 100 of these knives were made in various styles for various members of his sons’ companies of Georgia troops. This particular example has a 10-1/4″ double-edged blade which is very thick and well made. This knife is similar, if not identical, to a knife pictured in an image on p. 212 in William Turner’s book Even More Confederate Faces. Cooper Iron Work knives are rarely offered. Mr. Michel’s Notes State: “This well made, spear point Bowie knife has a 10-3/8” blade which is 1-7/8” wide. The hilt is identical to that of the D-guard Bowie belonging to Captain Eli M. Seago of Company F, 20th Georgia Infantry. It is also identical to the hilt of the Bowie knife protruding from the belt of the Southern infantryman whos photograph appears at the top left of page 212 in William Turner’s book, ”Even More Confederate Faces“. While the blade is different in that it is a spear point rather than the clipped point of Captain Seago’s Bowie, the length and width of the blades of each knife are about the same. At one time, this knife was identified as having been made at the Etowah Iron Works of Etowah, Georgia, which apparently made “handsomely mounted, of excellent workmanship and most beautiful finish” knives for the Atlanta Grays in 1861. In Daniel D. Hartzler’s book, ”Confederate Presentation and Inscribed Swords and Revolvers,“ wherever the Seago knife is pictured and described, however, he attributes the knife as the product of the Cooper Iron Works at Cartersville, Georgia.” CONDITION: Blade is gray with areas of staining and pitting. Brass has pleasant patina, as does wood handle. Guard exhibits several bends and top of pommel shows numerous dents and scratches. 4-31400 JS15 (6,000-8,000)

CONFEDERATE CLIP POINT BOWIE KNIFE WITH SCABBARD. This massive clip point Bowie is over 21″ long. Blade is 16″ long and 2″ wide. 7″ long iron crossguard protects a formed wood grip, retained with 2 peened over iron pins which hold grip to blade tang. Scabbard is sewn black leather. Scabbard once had a sewn belt loop which is now missing. Deeply scratched into the leather scabbard is “2th VA.” Mr. Michel’s Notes State: “This massive, clip point Bowie knife has a 16” long, 2” wide blade. The crossguard is of iron and the tang of the blade is held to the wood grip where it has been inlet for 3¼” by two iron rivets peened over iron washers. The scabbard is of heavy leather, all hand sewn. It has lost its belt loops, which from the stitching holes were two loops crisscrossed on one side and a single, diagonal loop on the other, enabling its owner to wear the knife at an angle on either side of his body. Deeply scratched into the leather of the scabbard is “2th Va”.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Crossguard exhibits good patina, as does wood handle and iron retaining pins. Black leather scabbard retains much of its orig black coating. Tip of scabbard has an old, glued repair. Spine of leather scabbard appears to have a contemporary leather repair. 4-31401 JS17 (5,000-8,000)

CONFEDERATE D-GUARD BOWIE KNIFE WITH BELT. This classic, Confederate, blacksmith-made, 17″ clip-point Bowie knife has blade over 12″ long and exhibits a 7-1/2″ false edge. Blade shows orig grinding marks. D-guard is beautifully made with a large, flat, bulbous quillon. Tiger maple grips exhibit two 1/2″ iron ferules. Scabbard is tin, covered in leather, with a belt sewn to scabbard. Belt retains its orig hand-forged roller buckle. This feature of sewn belts to leather scabbards was typically done in the period, though due to the fragility of such combinations, rarely did these survive with the belts still attached. This knife has orig tag with old brown ink stating “Taken from a dead Rebel by Ezequiel W. Chamberlain, Company K, 4th Mass Regiment on the battlefield of Camp Bislum”. This is as fine an example of a battlefield-found, classic, blacksmith-made, Confederate knife that you will ever have the chance to buy. Mr. Michel’s Notes State: “Confederate D-guard Bowie knife with a massive, upswept, clipped point. The scabbard is tin covered with leather and stitched directly onto the belt rig which closes with an iron roller buckle. With the rig is an old tag reading, “Taken from a dead Rebel by Ezekiel W. Chamberlain, Com K, 4th Mass Rat on the battlefield of Camp Bislum”. The “D”-guard is of iron with an iron ferrule at the ends of the grip which appears to be of maple wood. The knife blade is 12” long and 2-1/8” wide.” PROVENANCE: Ben Michel collection. CONDITION: Knife overall appears to be a typical “attic” find. Blade is gray with scattered staining. Tip of blade is blunted. Orig tool marks on blade are present. Iron hilt and roller buckle are uncleaned and have good patina. Maple grips show several age cracks but are sound and show good patina. Orig tag is laminated between two pieces of plastic. Leather belt is complete but is fragile. Leather covering scabbard is almost complete and shows several cracks on reverse. 4-31399 JS14 (6,000-8,000)

CONFEDERATE CLIP POINT BOWIE KNIFE WITH SCABBARD. This massive, 18-1/2″ knife with 12-3/4″ clip point blade is a classic Confederate, blacksmith-made knife. This knife exhibits an iron crossguard with pewter ferule, brass butt cap, and wood grip. Scabbard is sewn leather with numerous brass rivets protecting cutting edge and retained belt loop. This knife is a fine example of a Confederate side knife in its orig scabbard. It appears to have gotten wet at some time in its life, and blade has large areas of rust and pitting which have never been cleaned. In the scabbard, this knife will display as well as any Confederate side knife available. Mr. Michel’s Notes State: “This massive Bowie knife with its 12¾” long and 2” wide blade is the classic type with which proud Confederate soldiers displayed in the photographs they had taken as they departed for the war. It is well made with a heavy iron crossguard, pewter ferrule, well formed wood grip, and brass pommel plate, through which the tang of the blade is secured. The thick leather scabbard is seamed with 17 copper rivets, all of which, save one, are present. The scabbard is reinforced by an extra strap of leather at the throat and has a heavy leather belt loop secured by two of the same copper rivets as on the edge.” PROVENANCE: Ben Michel collection. CONDITION: Overall knife appears in “attic” condition. Blade exhibits areas of orig polish, though blade has areas of heavy pitting and staining. The 3 different metals composing grip all exhibit good patina. Wood retains good patina and shine. Scabbard is crazed and missing orig black surface at final 5″ on obverse. 4-31402 JS16 (5,000-8,000)

CONFEDERATE D-GUARD BOWIE KNIFE. This massive, 19″ clip-point bladed, fighting knife utilizes a US 1860 cavalry hilt and pommel as this knife’s hilt. Hilt has had the branches removed. Pommel still retains “US” inspector marks. Grip is also a cavalry grip with sgl iron wire. Scabbard is backsewn leather with brass drag and throat attached with iron wire. Scabbard throat has serial number which is no longer legible. Opposite side of throat has a center mounted brass frog button. Scabbard mounts are decorated with incised lines. Mr. Michel’s Notes State: “This massive, 19” blade cutlass is made with a 1¾” wide, brazed blade mounted onto a modified brass sword hilt with branches removed to create a single branch guard. The grip is covered with tarred canvas wound with heavy iron wire. The scabbard is heavy, dark, russet leather with a brass tip and throat.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Blade retains orig protective leather washer. Guard is bent over at spine. Grip appears tarred or painted and retains much of this orig finish, though chipped and worn at high spots. Iron wire wrap is intact and complete. Brass guard and scabbard mounts have been cleaned. 4-31397 JS13 (2,000-4,000)

FAYETTEVILLE SABER BAYONET. This is among the most difficult of all Confederate bayonets to find in good condition, and this one is excellent overall. 21-1/2″ blade still has areas of orig shine and polish. Feathered brass hilt exhibits fine patination and retains orig spring and button. Only marking on this bayonet is a letter “L” stamped on spine of hilt. Accompanying scabbard appears orig and could not fit bayonet any better. Scabbard is back sewn with pin-retained brass mounts. Throat has round frog button. This is the finest Fayetteville bayonet we have ever seen at auction. These bayonets were well used, and few survived with blade and hilt this fine. Mr. Michel’s Notes State: “This Fayetteville sword bayonet in its original scabbard is one of the finest in existence. The 21¾” blade is uncleaned with only some age staining. The hilt is also untouched and marked only with a small “L” on the back. The scabbard is original to this saber bayonet and while there is flaking to the leather, it is still sound and complete.” PROVENANCE: Ben Michel collection. CONDITION: Blade is bright/gray with scattered areas of staining and pitting. Brass hilt and scabbard mounts exhibit good patina. Spring retains traces of blue under an overall pitted surface. Scabbard body is crazed with about 30% of black coating chipped away. 4-31332 JS24 (6,000-8,000)

CONFEDERATE SABER BAYONET MADE BY BOYLE & GAMBLE, RICHMOND, VIRGINIA. This is a fine example of a well-made Confederate bayonet in its orig scabbard. Though this bayonet is unmarked, we know it is a product of Boyle & Gamble, because similar specimens have cast guards saying “Boyle, Gamble & McFee, Richmond, VA”. This bayonet has a 20-1/4″ blade. Hilt is hollow-cast, and on this specimen is very nice with no dents. Often, these bayonets are dented. This bayonet appears in uncleaned, “attic” condition. Scabbard is top sewn with brass throat with Boyle & Gamble style, spade-shaped frog button. This same shape frog button is found on other Boyle & Gamble products that used frogs. Throat is retained with a single pin, as was the brass drag, which unfortunately is missing. You are bidding on a high-condition Boyle & Gamble bayonet in the rarely found orig Boyle & Gamble scabbard. Mr. Michel’s Notes State: “This Boyle, Gamble & McFee saber bayonet is one of the finest in existence. The 20¼” blade is uncleaned with only some age staining. The hilt is also uncleaned and retains its aged brass color. The scabbard is original to this bayonet and correct in pattern. The leather has some flaking and is loose at the stitching at the top of the scabbard but is otherwise sound and complete.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Hilt and scabbard throat are very good, exhibiting only minor scratches and dents. Orig spring and button are present with scattered pitting. Leather scabbard body has come unsewn at seam and has lost much of its orig black surface. 4-31333 JS27 (4,000-6,000)

COOK & BROTHER SABER BAYONET. SN 1311. This Cook & Brother bayonet was made in Athens, Georgia. Only the earliest Athens, Georgia bayonets are serial numbered, and this was one of the first one or two hundred, as about 1,000-1,200 rifles were made in New Orleans, and the SN started thereafter in Athens. Blade measures 21-1/2″ and shows the typical Yahtaghan curviture with unstopped fuller, typical of this manufacturer. This bayonet is marked with SN on crossguard and is fitting with triangular-shaped slot in hilt for the saber bayonet lug. Accompanying scabbard for this bayonet is brass mounted and back sewn. Mounts were attached with wire. Mr. Michel’s Notes State: “Cook & Brother saber bayonet in brass-mounted, leather scabbard. This full length blade at 21½” has a heavy yataghan curvature with an unstopped fuller which extends 6” from the tip to 1¼” before the crossguard. This bayonet is marked with serial number “1311” on the crossguard and is fitted with the triangular-shaped slot in the hilt for the saber bayonet lug. The serial number range, combined with the triangular slot, indicate this bayonet was produced after the move to Athens, Georgia, when the rifles were no longer fitted with square saber bayonet lugs on the barrel and were intended to utilize one of the brass bayonet adapters made by the company with a triangular lug. The scabbard has a brass throat and tip and is sewn at the lower edge.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with areas of pitting, staining, and old grinding marks. Spring and button are possibly replaced. Scabbard is solid but dry. Drag is cleaned and missing retaining wires and glued into place. 4-31294 JS26 (2,000-4,000)

COOK & BROTHER SABER BAYONET. SN 2. This saber bayonet exhibits a 21-1/2″ blade with a distinct Yataghan curvature with an unstopped, fuller which extends 6″ from the tip to 3″ from the crossguard. Bayonet is marked with SN on crossguard, retains orig spring and button and has brass-mounted scabbard of unknown manufacture. Because of this very low serial number and the square slot in hilt, this bayonet was produced in New Orleans, where the rifles were fitted with a square bayonet lug affixed to the barrel, as opposed to later production in Athens, GA, where the saber bayonets were affixed to the barrels using a detachable brass bayonet adapter with a triangular lug fitting into a triangular slot in the hilt of the bayonet. Mr. Michel’s Notes State: “Cook & Brother saber bayonet in brass-mounted, leather scabbard. The full length blade at 21½” has a distinct yataghan curvature with an unstopped fuller which extends 6” from the tip to 2” before the crossguard. This bayonet is marked with the serial number “2” on the crossguard and is fitted with the square slot in the hilt for the saber bayonet lug. This low serial number, combined with the square slot, indicates this bayonet was produced in New Orleans, where the rifles were fitted with a square bayonet lug affixed to the barrel as opposed to subsequent production in Athens, Georgia, where the saber bayonets were fixed to the barrels using a detachable, brass bayonet adapter with a triangular lug fitting into a triangular slot in the hilt of the bayonet.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with scattered areas of staining and pitting. Rough cast hilt exhibits nice patina. Orig spring and button show scattered pitting. Scabbard mounts are cleaned. Leather body of scabbard is dry and recolored black. 4-31293 JS25 (2,000-4,000)

CONFEDERATE SABER BAYONET. SN 190. This saber bayonet has recently been identified as being manufactured by Louis Froelich at the Confederate States Armory in Kenansville, NC. This well-made bayonet exhibits a blade just over 19″ and SN is stamped into the pommel of its brass hilt. Froelich made bayonets of different blade lengths, but blade characteristics are all similar, as are the hilts. This is a fine example of a Confederate bayonet in “attic” condition. Mr. Michel’s Notes State: “Confederate saber bayonet manufactured by Louis Froehlich at the Confederate States Armory located in Kenansville, North Carolina. This is the version with the shorter, lighter blade, only 19¼” long, with an unstopped fuller running from 1¼” from the hilt to 5” from the tip. The stud lock and stud lock spring are intact. The pommel cap is numbered “190”.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Hilt retains good patina and areas of shine under old varnish. Trace of orig blue is found on orig locking spring. 4-31328 JS21 (2,500-3,500)

CONFEDERATE SABER BAYONET. This bayonet, thought to be made by Louis Froelich at the Confederate States Armory, Kenansville, North Carolina, is complete with its orig Confederate-made scabbard and frog. This is the only example of the Froelich scabbard we know of that has ever been sold at auction. Blade is 21-1/2″ long. Hilt, like other specimens, is ribbed and unmarked. Bayonet is missing spring and button. Scabbard is top sewn with brass throat and brass drag. Throat retains a teardrop-shaped frog button with its orig sewn frog. Mr. Michel’s Notes State: “Confederate saber bayonet manufactured by Louis Froehlich of the Confederate States Armory in Kenansville, North Carolina in original scabbard. Long, 21½” blade with unstopped fuller extending from the ricasso to some 6” from the tip. The hilt is unmarked and is missing the stud lock and stud lock spring. The full length, original scabbard is top sewn with a brass throat and tip. The top throat has a teardrop-shaped stud to hold the waist belt frog, which is also present and still intact.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with scattered staining and pitting. Blade is loose in hilt. Hilt has numerous dings and scratches and is missing spring and button. Scabbard body is solid but dry. Frog is solid, crazed, with some loss of black surface. Orig drag is resoldered/braised at seam and cleaned. Throat is untouched and exhibits nice patina. 4-31331 JS22 (4,000-6,000)

CONFEDERATE SABER BAYONET. This bayonet has many characteristics of the Louis Froelich bayonets and could possibly be one of their products. Blade on this example is larger than on most known Froelichs at over 22″ long and 1-1/4″ wide. This bayonet appears in as found, “attic” condition. Sword retains scabbard with brass throat and drag, which fits bayonet well. Scabbard body is back sewn and is of unknown manufacture. Throat is affixed with brass wire. Mr. Michel’s Notes State: “Confederate saber bayonet resembling those made by Froehlich at the Confederate States Armory in Kenansville, North Carolina, but with a wider, finer manufactured blade than found on Froehlich’s products. The hilt is, however, almost identical to the casting of the hilt on Froehlich’s bayonets. The blade is 22¼” long, well finished, about 1¼” wide and with an unstopped fuller running 1” from the crossguard to about 6” from the tip. The scabbard is original to this bayonet and is in sound condition.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Hilt exhibits good patina. Scabbard tip and throat exhibit numerous scratches and dents. Scabbard body has one central cut, approx. 1/2″ long. Scabbard surface is crazed and mottled. JS23 4-31329 JS23 (2,500-3,500)

CONFEDERATE “MONSTER” SABER BAYONET. This rarely-encountered, massive, Confederate saber bayonet has a thick blade which is 20-1/2″ long and massive brass hilt. This bayonet is missing locking spring and still weighs over 2-1/2 lbs. It is unknown what gun this bayonet fit. There are probably more excavated specimens of this bayonet, due to the fact that it weighed so much. The soldier was very happy to throw it away in camp or after the battle and not have to further tote it. Mr. Michel’s Notes State: “Confederate saber bayonet with massive, thick yataghan-shaped blade. The blade is 20½” long with a crude, unstopped fuller, which beings about 2½” from the crossguard and runs almost to the tip. The hilt is equally massive and noticeably shorter than found on other saber bayonets. The lug and the spring retainer which clamps the hilt to a bayonet lug are missing.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with scattered areas of staining and pitting. Point is rounded. Hilt exhibits numerous small scratches and dings with good patina. Locking spring is broken off, but still has retaining pin and base of spring. 4-31330 JS20 (3,000-4,000)

CONFEDERATE SABER BAYONET. This Confederate-made saber bayonet exhibits 18-3/4″ flat, unfullered blade which shows typical longitudinal faults seen in other Confederate blades. Hilt is marked with 5 small dots on spine. These 5 dots occur on other Confederate-made short swords and bayonets, but we are unaware of who made them. Locking pin and spring and missing. Mr. Michel’s Notes State: “Confederate saber bayonet with flat, 18¾” blade. The blade of this bayonet, strangely yataghan in form, is unusual in that there is no fuller. The hilt is unmarked except for five punched dots on the back. The stud lock and the stud lock spring are missing. The tang of the blade is recessed about 1/8” from the end of the hilt at the pommel, as if an effort had been made to unseat the blade by driving against the tang where it exited the pommel.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/brown with old sharpening. Hilt exhibits good patina. Blade tang is recessed about 1/8″ into pommel. Vice marks are visible on blade ricasso. 4-31327 JS19 (1,500-2,500)

CONFEDERATE “TREDEGAR” SOCKET BAYONET. This socket bayonet is well accepted as the most commonly encountered Confederate manufactured angular bayonet. For many years, this bayonet was accepted as a product of the Tredegar Iron Works, but there are competing beliefs that they were made at Raleigh, North Carolina, or at the CS Armory in Richmond, Virginia. Wherever they were made, they are unquestionably Confederate manufactured. Blade is triangular in shape with no flutes on any of the sides. Bayonet is iron with a braised steel tip. These bayonets are commonly excavated as rusted-out relics. Rarely are they offered in fine, non-excavated condition. This is indeed a fine example of this rarely seen Confederate edged weapon. These bayonets are found in several configurations and calibers. This bayonet is made to fit a 69 cal. Model 1842 musket or a Model 1816 conversion musket. This is the first Tredegar-style bayonet we have ever seen come to auction. Mr. Michel’s Notes State: “This socket bayonet is well accepted as the product of the Tredegar Iron Works, but there is a competing belief that they were made at the CS Armory at Richmond. Wherever they were made, they are of unquestionable Confederate manufacture. The blade is triangular in shape with no flutes on any of the sides. This bayonet has a socket to fit a .69 caliber musket.” PROVENANCE: Ben Michel collection. CONDITION: Overall, surface is gray with scattered areas of staining and pitting. There is a cut in one of the angles of blade. There are several bends to blade and socket, but bayonet still fits on a 69 cal. musket quite snugly. 4-31326 JS18 (2,500-3,500)

CONFEDERATE IMPORTED ENFIELD CUTLASS BAYONET. SN 975. This is a rare example of a Confederate, serial numbered, blockade run, Model 1858 saber bayonet with massive 26-3/4″ blade. Like other English edged weapons of the period, basket is iron and grip is compressed leather held by iron pins. SN 975 is engraved on bolster. This number would have corresponded to a Model 1858 Blockade run English rifle with same SN. Mr. Michel’s Notes State: “Enfield cutlass bayonet with 27” blade and iron cup hilt. The pommel is engraved with the same size and style numbers found on the buttplate tang of Enfields imported to the Confederacy, in this case “975”.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with large areas of pitting, though proofs and maker’s mark are still visible. Grips are intact, though chipped and shrunk. 4-31314 JS6 (1,000-2,000)

CONFEDERATE BLOCKADE RUN ENFIELD SABER BAYONET. SN 650. This Enfield saber bayonet is complete with orig scabbard and frog. SN is cut longitudinally into pommel, as is typically found on other Confederate imported Enfield saber bayonets. SN would have been cut into buttplate of corresponding Enfield rifle that this bayonet would have fit. Bayonet is in beautiful condition. It must have been a trophy sold in prize court in the North that never made its way to Confederate service. You won’t find a nicer bayonet and scabbard. Though there is no serial number on scabbard, it appears to have always been with this bayonet, as condition and surfaces match perfectly. Mr. Michel’s Notes State: “Enfield saber bayonet with scabbard and white buff frog in excellent condition. All metal is uncleaned bright and all the leather is sound, including the leather grips of the bayonet itself. The hilt of the bayonet is engraved with the typical numbers placed on arms imported from England by the Confederacy, in this instance “650”.” PROVENANCE: Ben Michel collection. CONDITION: Blade is bright with light areas of pitting. Hilt is very good, with scattered areas of rust staining on pommel and scabbard mounts. Compressed leather grips are very good. Leather scabbard body is very good. White, buff frog is very good, showing scattered soiling. 4-31318 JS28 (1,000-2,000)

ENFIELD SABER BAYONET. SN 574. This bayonet, like 4-31318, is probably a Blockade Run bayonet; however, this bayonet has a SN in the crossguard different than those that are unquestionably known to be Confederate. SN 574 is stamped in large numbers in crossguard, similar to those stamped into the wood of iron-mounted, Confederate imported rifles. Mr. Michel’s Notes State: “Saber bayonet for Enfield rifle. Crossguard marked with Confederate inventory/serial number “574”.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray with scattered staining and pitting. Leather grips are worn, scuffed, scratched, and shrunk. Locking button is missing, but spring is retained. 4-31322 JS29 (300-500)

CONFEDERATE “JOE BROWN” PIKE. The Governor of GA, Joseph Brown, in 1861, asked the mechanics of GA to produce him pikes such as this so the state could be defended by civilians against the predicted Yankee hordes invading. Such weapons were rarely used, but many were found in storage in places like the Augusta Arsenal at the end of the war. This is a neat variant by unknown maker. Pike overall is approx. 8-1/2′ long. Its spear point is 12″ long x 1-3/8″ wide. There is a “W” stamped on the ricasso of blade. A brass ferrule approx. 2″ holds blade. An unusual 7″ cast iron cap is found at base of staff. This is a nice example of a Confederate pike that was probably brought back north as a souvenir after the war. Mr. Michel’s Notes State: “Confederate pike with full length shaft and ferrule at base. Brass ferrule at blade. Spear point blade with flat ricasso.” PROVENANCE: Ben Michel collection. CONDITION: Wood staff is solid and straight with minor scrapes and gouges. Ferule and butt cap are complete, as are reinforcing straps, which are pitted. Blade is gray with scattered areas of staining and pitting. Maker’s mark “W” is crisp. 4-31403 JS113 (1,000-2,000)

ENFIELD SOCKET BAYONET. This bayonet has possible Confederate association from an unusual engraved number on socket. Most typically, numbers are engraved longitudinally. This has 3 sets of 2-digit numbers stamped vertically above each other. Mr. Michel’s Notes State: “Socket bayonet for Pattern 53 Enfield rifled musket with Confederate inventory/serial numbering. Numbers are engraved on socket in three lines “36 / 26 / 71”.” PROVENANCE: Ben Michel collection. CONDITION: Surfaces are gray/bright with scattered staining and pitting. 4-31323 JS30 (200-400)

COOK & BROTHER BAYONET ADAPTER. Seldom found, this Athens, Georgia made bayonet adapter was fitted on early Athens, Georgia made rifles for benefit of accepting saber bayonets of their manufacture. Adapter has a very distinctive, triangular lug which fitted into the cutout on the Athens made saber bayonets. Mr. Michel’s Notes State: “Cook & Brother saber bayonet adapters were utilized with the rifles produced at Athens, Georgia. They have a triangular lug which fitted into the triangular cutout in the hilt of the saber bayonet” PROVENANCE: Ben Michel collection. CONDITION: Adapter has been cleaned, showing numerous casting flaws. Retaining screw appears orig. 4-31295 JS70 (500-1,000)

COOK & BROTHER BAYONET ADAPTER. Athens-made bayonet adapter with SN 66 stamped on flat, triangular lug. Adapter appears larger and heavier than most encountered. Mr. Michel’s Notes State: “Brass bayonet adapter with triangular stud. Large size for M1841-type rifle.” PROVENANCE: Ben Michel collection. CONDITION: Surfaces are good and smooth with good patination. SN markings are crisp. Orig finishing marks are visible. Retaining screw appears orig. 4-31296 JS69 (500-1,000)

BOYLE, GAMBLE & MCFEE BAYONET ADAPTER. This adapter is SN 59 on lug and is maker marked “BG&M / Richmond VA / Patent Sept. 2, 1861”. Adapter is excavated. It still retains dirt from some unknown battlefield or campsite. Mr. Michel’s Notes State: “Boyle, Gamble & McFee bayonet adapter made of brass and well marked, “B. G. & M / Richmond Va / Pat Sept 2, 186” on the body and number “59” on the lug. These adapters were designed to provide a lug for the barrel of rifles manufactured without an integral bayonet lug affixed to the barrel.” PROVENANCE: Ben Michel collection. CONDITION: As excavated with ground action and dug patina. Missing set screw. Markings are discernible. Still retains proper curvature for gun. 4-31334 JS70 (500-1,000)

HISTORIC FIRST MODEL LeMAT REVOLVER CAPTURED FROM THE CONFEDERATE IRONCLAD “ATLANTA” SERIAL NUMBER 7. SN 7. One of the most historic and important Confederate associated revolvers to come to market in recent memory is this rare First Model LeMat revolver serial number 7. LeMat revolvers were invented by Dr. Jean Alexandre Francois LeMat of New Orleans. The LeMat revolver is a .42 caliber cap & ball black powder revolver which featured a rather unusual secondary 16 gauge smoothbore barrel capable of firing grapeshot. The First Model LeMats were produced in Paris in 1862 and featured a spurred trigger guard, part round, part oct bbl and a swivel lanyard ring attached to the butt cap. All iron, these revolvers had checkered walnut two-piece grips. This is also the lowest SN known on any LeMat. This LeMat is, properly, marked on the top barrel flat “Col. LeMat’s Patent” (pictured in Adams’ book but misidentified as serial number 15). On the right side of the grip is a small silver plate, affixed with two pins and engraved “ATLANTA.” Documentary evidence for the inventory of this Confederate ironclad ship lists three LeMat revolvers. Only two other documented LeMat revolvers exist with Confederate Naval usage. CSS Atlanta , an 1006-ton ironclad ram, was originally built in Scotland in 1861 as the merchant steamship Fingal . In November 1861 she ran the blockade into Savannah, Georgia, with a large cargo of weapons and military supplies. After Union forces closed the exits from Savannah, preventing her further use as a blockade runner, Fingal was converted to an casemate ironclad and renamed Atlanta . She made her first appearance as a Confederate warship in mid-1862. Atlanta made two efforts to attack Federal warships blockading the coast and rivers leading to Savannah. The first, in early 1863, was thwarted by obstructions blocking the route to the sea. In June 1863 Atlanta made her second attempt, targeting blockaders in Wassau Sound. There, on the 17th, she encountered the U.S. Navy monitors Nahant and Weehawken . In a brief battle, Atlanta went aground and was overwhelmed by Weehawken ‘s superior firepower, forcing her to surrender. The captured ironclad was taken into the Union Navy as USS Atlanta , commissioning for service in February 1864. She was stationed on the James River, Virginia, to support the operations of the army under General Grant. On 21 May 1864, she fired on Confederate cavalry that were attacking Fort Powhatan. A year later, with the Civil War over, Atlanta went north and decommissioned at Philadelphia, Pennsylvania, in June 1865. After several years “in ordinary”, she was sold in May 1869. Reportedly, she subsequently became the Haitian warship Triumph and disappeared at sea off Cape Hatteras in December 1869. This is the lowest serial number known among all LeMats, is among the best condition and is among the most historic. What more could you want in a great LeMat? Mr. Michel’s Notes State: “First Model LeMat revolver captured with the surrender of the Confederate ironclad ”Atlanta.“ This revolver, serial number 7, is the lowest serial number revolver with an established Confederate usage. (The revolver is misidentified in ”The Confederate LeMat Revolver“ by Doug Adams as being serial number 15.) Inlet into the right grip is a small silver plate engraved “Atlanta”. The inventory of the ironclad ”Atlanta“ included three LeMat revolvers. The revolver is in superb condition, well marked with the serial number 7 on virtually every component. It is one of only three with known association with the effort of the Confederacy to create a naval force, the other two being serial number 183, captured aboard the Confederate Commerce raider ”Florida“ (also marked on the left side of the frame “Captured in the Rebel Steamer Florida”) and serial number 946, carried by J. N. Maffitt, the Captain of the ”Florida“. The ”Atlanta“ was a refitted iron steamship of English origin which had run the blockade in November 1861. Taken by the Confederate government and rename, the ”Atlanta,“ it was then altered and strengthened for service as an ironclad man-of-war. Leaving the Wilmington River and entering Wassau Sound for the purpose of raising the blockade, at that point it was confronted by the Union monitor,” Weehawken“ under Capt. John Rodgers. The action, as described in James Russell Soley’s book published in 1883, ”The Blockade and the Cruisers,“ was brief: “With the deliberateness which characterized him in the most trying moments, Rodgers delivered the fire of his two heavy guns, the XI-inch and the XV-inch. He fired five shots, of which four hit the ”Atlanta. “The first, a XV-inch cored shot, struck the inclined side of the vessel, in the line of the ports; and though fired at an angle of fifty degrees with her keel, penetrated the armor and, ripping out the wooden backing, the two layers of which were the brittle Georgia pine, covered the deck with splinters. From the effects of this shot, forty or more men were prostrated, several of whom received ugly wounds from the fragments of wood and iron. The second shot, from the XI-inch gun, struck the edge of the overhand, and started the plating. The third carried off the roof of the pilot-house, wounded the two pilots, and stunned the men at the wheel. The fourth shattered a port-shutter, driving the fragments in through the port.” After its capture, it was found that the ship had actually run aground and was apparently unable to maneuver. With the revolver is a copy of a photograph taken of the ”Atlanta “after its capture and a copy of a line drawing of the ship under steam. The octagon to round barrel is marked, correctly, only “Col. LeMat’s Patent”.” CONDITION: Fine, this revolver is well marked, retains a nice dark patina overall with very little pitting. Showing light wear, the LeMat functions mechanically well and is correctly marked with the serial number 7 throughout. A marvelous opportunity to obtain a rare First Model LeMat with long established Confederate Naval usage and capture. One of the finest examples known with a rich history. 4-31368 CW2 (50,000-100,000)

RARE AND DESIRABLE CONFEDERATE FIRST-SECOND MODEL TRANSITIONAL LeMAT REVOLVER. SN 637. One of the most desirable and important Confederate revolvers on the market today is this rare Transitional First-Second Model LeMat revolver serial number 637, all matching. LeMat revolvers were invented by Dr. Jean Alexandre Francois LeMat of New Orleans. The LeMat revolver is a .42 caliber cap & ball black powder revolver which featured an unusual secondary 16 gauge smoothbore barrel capable of firing grapeshot. This First Model LeMat was produced in Paris France in 1862-3 and features a spurred trigger guard, part round, part octagon barrel and a swivel lanyard ring (missing) attached to the butt cap. All iron, these revolvers had checkered walnut two-piece grips. This distinctive revolver exhibits most of the major features of the Second Model LeMat, however, the First Model style spurred trigger guard has been retained as has the lever release for barrel immediately below the shotgun barrel and the lanyard ring (missing) is attached with a pin instead of being cast integral with the butt cap. On the right face of the barrel is the mark “LM” surmounted by a 5-pointed star. The early 2nd model barrel marking reads “COL. LeMat BTE. s.g.d.g. PARIS” appears across the top barrel flat in fancy script. Here we have a rare transitional model showing the improvements made to the Second Model LeMat revolver while retaining some of the features of the First Model. Very few of these Transitional Models are known and this revolver represents a rare opportunity to obtain one. Mr. Michel’s Notes State: “LeMat revolver serial number 637 is an example of what has been referred to as “transitional” between the first model and the second model. The trigger guard with finger grip extension is typical of the first model, as is the swivel lanyard ring in the butt cap (missing on this piece), but the loading lever is now moved from the right side of the frame to the left side, characteristic of the second model of this revolver. The serial number appears on essentially every part. The octagon barrel is marked (in small, Old English lettering) “Col. LeMat Bte S.G.D.G. Paris” in an engraved panel.” CONDITION: Very Good. No original finish remains but all iron parts have evenly aged to a mellow dark brown patina. The grips show light wear consistent with handgun. Never cleaned and, with no visible pitting, this LeMat is in very attractive condition. 4-31369 CW7 (20,000-22,000)

RARE CONFEDERATE LeMAT SECOND MODEL REVOLVER. SN 1635. One of the nicest 2nd Model LeMat revolvers recently seen on the market. This example has the earliest 2nd model barrel marking dating it to the late war period 1864-65. The LeMat revolver is a .42 caliber cap & ball black powder revolver which featured a rather unusual secondary 16 gauge smoothbore barrel capable of firing grapeshot. This 2nd model was manufactured in France and has the distinctive round trigger guard without spur. Full octagonal barrel with loading lever on the left side and a lanyard ring cast in general with the steel butt cap. Serial number 1635 all matching. On the right face of the barrel is the mark “LM” surmounted by a 5-pointed star. The early 2nd model barrel marking reads “COL. LeMat BTE. s.g.d.g. PARIS” appears across the top barrel flat in fancy script. The revolver is all iron with a two piece checkered walnut grip. Mr. Michel’s Notes State: “This LeMat revolver, serial number 1635, is typical in all regards of the second model, including elimination of the finger grip on the trigger guard and the swivel ring in the buttcap and location of the loading lever on the left side of the revolver. The cylinder still contains considerable of its blued finish and the barrel also shows traces of blued finish as well. The serial number appears on essentially every part. It is missing the pin securing the barrel housing to the frame and one nipple is broken off in the cylinder. The barrel is marked in large, Old English letters, “Col. LeMat Bte S.G.D.G. Paris” in an engraved panel.” This novel revolver was first patented in America in 1856 and later in several European countries. They were popular with a number of high ranking Confederate officers and a substantial number of them were purchased by the Confederate States of America under a direct government contract. CONDITION: Fine. This example retains much of its original factory blued finish in protected areas. The cylinder retains about 90% of its finish and the barrel about 50% being worn at the muzzle and near the breech. The iron frame and remaining parts, with minor traces of blue, have turned a pleasing plum brown color. The grips show very little wear and the revolver is mechanically fine. One screw, on the right side of the frame has minor damage to the slot. The frame release pin is missing and one nipple is broken. A marvelous opportunity to obtain one of the most desirable Confederate handguns in truly nice condition. 4-31370 CW6 (20,000-24,000)

SCARCE AND RARE CONFEDERATE NAVY CONTRACT LeMAT AND GIRARD’S PATENT LONDON TWO BARREL REVOLVER. SN 8074. A fine example of this London, England Made LeMat Revolver manufactured about 1865. This was the last percussion revolver manufactured under LeMat’s patent. Caliber 42 rifled barrel & 16 gauge smoothbore. Serial Number 8074. In the book on LeMats by Doug Adams, Adams states the London LeMats serial numbered 8000-9000 were a Confederate Navy contract made by Tipping & Co. in England. Late London made LeMat with 6-9/16″ octagon barrel with block letter address on top flat “LEMAT & GIRARD’S PATENT LONDON”. It has the tall LeMat front sight & has the serial number on right flat in front of cylinder. Serial number also appears on right front side of frame and barrel near the breech. No serial number was observed on smoothbore bbl but it does have two Birmingham proofs & number “18” which probably refers to bore diameter. It has left side rammer that operates in a channel between barrel and rear barrel boss and the serial number on inside of rammer handle. It has single pin barrel assembly lock with knurled head. It has a center mounted articulated hammer nose & 9-shot cylinder that pivots around smoothbore barrel and has serial number with Birmingham proofs around perimeter. It has integral solid butt cap & lanyard loop without ring. This revolver represents one of the important models in the string of variations produced in this revolver. With the documentation in Adams’ book, it is highly likely that this revolver was manufactured on contract for the Confederacy. Mr. Michel’s Notes State: “This is the final version of the percussion LeMat revolvers, made by C. Girard & Co. under contract with the Confederate Navy Department. IT is serial numbered 8074 on all the component parts and the barrel marked in block letters “LEMAT & GIRARD’S PATENT LONDON”. It still has considerable blue/brown finish overall except for the hammer, which was apparently finish bright.” CONDITION: Fine. This LeMat retains much of its original blued finish, about 50% on the barrel and 80% on the cylinder. The remaining metal parts have a nice dark, uncleaned brown patina. The grips show appropriate wear. 4-31371 CW8 (19,000-23,000)

FIRST MODEL GRISWOLD REVOLVER. SN 810. Cal. 36. Standard 1st Model Griswold. 1st Models externally are differentiated from later guns due to the round barrel housing. SN appears on bbl housing, cyl, frame, trigger guard, and backstrap. Secondary number “10” appears on wedge, loading arm, and inside stocks in red pencil. The cryptic “DD” is stamped on backstrap, trigger guard, and frame internally and is also visible on back of cyl. A secondary number “26” is stamped on top of base pin. This is the only Griswold I have ever encountered with a number stamped there, and base pin is absolutely correct for this gun, showing typical Griswold features, such as the way the slot is made and the way the grease grooves are cut. This gun’s frame also has unusual characteristics of six half moon-shaped, raised areas cast into raised platform ring in back of frame. Their purpose is unknown, and this is the only gun we have noted with this feature. Early 1st Model Griswolds are scarce; maybe this feature occurs on others. This is a well-known gun, formerly in the collection of Henry Stewart, who purchased this gun from a barber in Lexington, VA, while he was attending the Virginia Military Academy. It is pictured on p. 28 of Robert Abel’s book, published in 1950, Early American Firearms. This is one of the earliest published Confederate handguns, and it presents very nicely, showing the characteristic twisted iron in the cyl and bbl, so typical of Griswold revolvers. Mr. Michel’s Notes State: “Manufactured by the partnership of Samuel Griswold and Arvin N. Gunnison in Griswoldville, Georgia, this revolver is typical of the earliest productions. The primary difference between the early and later production revolvers is in the shape of the barrel housing which is round in earlier production and octagonal in the later production. The change general occurs about serial number 1500 and this revolver, serial number 810, is with the round barrel housing characteristic of the earlier production. Well marked throughout, the serial number appears on the frame of this revolver, the cylinder, triggerguard, barrel, and grips. Not only is this revolver completely original, it is well documented. Formerly the property of Henry M. Stewart, it is pictured as the bottom revolver on p. 38 of Robert Abels’ book, published in 1950, ”Early American Firearms. “According to Mr. Stewart, he purchased the revolver from a barber in Lexington, Virginia, for $1.50 when he was a student at the Virginia Military Academy.” PROVENANCE: Ben Michel collection. CONDITION: Bbl and cyl have been overcleaned, revealing the very distinctive twist, characteristic of this manufacturer, especially in cyl. Front site is worn down. Brass surfaces cleaned. Stocks retain traces of orig varnish. Small shim has been welded to bbl housing where it attaches to frame. Markings are all clear and well struck with exception of weak SN on bbl housing, but it is still discernible. 4-31347 JS108 (15,000-20,000)

RARE CONFEDERATE GRISWOLD BRASS FRAME REVOLVER. SN 1531. This is one of the earliest SN in the Griswold 2nd Model range with 1510 & 1516 being the two earliest SNs. This Griswold & Gunnison revolver produced in Griswoldville, Georgia, serial number 1531 is a brass framed copy of the .36 caliber Colt Model 1851 Navy revolver with a 6-shot round cylinder, dragoon style barrel, octagon to round, with one-piece walnut grips and a brass frame, trigger guard and back strap. The serial is stamped in large numbers beneath the frame, on the bottom of the barrel lug, and on the cylinder. A single digit serial number “1” appears on the on the loading lever and trigger guard. Some 3,600 to 3,700 revolvers were produced by Griswold and Gunnison from about July 1862 until the destruction of the factory in the November 22, 1864 during the Battle of Griswold Station. There is speculation that either production continued elsewhere or parts were hidden prior to the battle as deliveries continued until April 1865. Samuel Griswold established a number of manufacturing enterprises in an area nine miles south of Macon, Georgia on the Georgia Central Railroad. This site became known as Griswoldville. In 1861, he shifted the cotton gin factory to the production of pikes for the Confederate Government. In mid 1862, he was joined by Arvin Gunnison, who had begun revolver production in New Orleans but had escaped just before that city’s capture. The Griswold brass frame copies of the Colt Model 1851 Navy were made in two patterns: One with a round top barrel housing and the second with an octagonal top barrel housing. This example is the so called “Second Model” with a 7.5 inch barrel, octagonal breech and brass frame. This is a fine example and represents a wonderful opportunity to obtain one of the most recognizable and desirable Confederate manufactured brass frame revolvers. Mr. Michel’s Notes State: “Typical of the later production of Samuel Griswold’s and Arvin N. Gunnison’s manufacture of pistols at Griswoldville, Georgia, this revolver has an octagonal barrel housing as opposed to the rounded housing which appeared on the earlier production pieces. Serial number 1531 places this revolver at about the transitional point in production. Not only is this revolver all completely original, it is well documented as once part of the collection of Robert Sutherland as an example of the Confederate copy of the Colt and is shown on p. 144 of the book devoted to his collection, ”The Book of Colt Firearms“ by Sutherland & Wilson.” CONDITION: Good. The revolver has been lightly cleaned a long time ago leaving small areas of pitting on iron parts. The brass frame and furniture have obtained a nice mellow patina. Some tool marks and dents appear on the right side of the barrel lug. The grips are very good with a shallow chip out of the left side at the toe. 4-31348 CW9 (20,000-24,000)

SPILLER & BURR REVOLVER. SN 345. Cal. 36. Spiller & Burr standard model revolver with “CS” stamped on left side of frame. SN occurs on bbl, frame, trigger guard, and inside stocks. Interesting is that inside the left stock is nicely scratched the name “John H. Fowler, 1888”. The right stock is similarly inscribed “J. H. F. / Elkton / MD”. I don’t know who Mr. Fowler is, but it would be interesting to know his story. Inside of frame is also marked with a cryptic letter “M”. This is an attractive specimen of the popular Atlanta & Macon made, brass-framed, Confederate revolver. Mr. Michel’s Notes State: “The partnership of Edward N. Spiller and David J. Burr produced their first revolvers at an Atlanta factory and then at Macon, Georgia. Total production was approximately 1,250 revolvers. This revolver is serial number 345 and is stamped “CS” on the left side of the brass frame. The serial number appears under the barrel, at the top of the grip frame, inside the trigger guard, and inside the wood grips. The inside of the left grip is inscribed “John H. Fowler 1888” and the inside of the right grip is similarly inscribed “JHF / Elkton Md”.” PROVENANCE: Ben Michel collection. CONDITION: Bbl is brown with scattered pitting. Hammer & cyl are also brown with scattered pitting. Loading assembly appears replaced and is smooth and brown. Mainspring appears replaced. Right stock has about a 1″ x 1/2″ chip repaired and a much smaller chip opposite it. 4-31352 JS107 (12,000-15,000)

CONFEDERATE LEECH AND RIGDON REVOLVER INSCRIBED BY A MISSISSIPPI CAVALRYMAN. SN 346. A fine early serial numbered specimen of this rare Confederate revolver made by Thomas Leech and Charles H. Rigdon in Columbus, Mississippi. Guns with small “Leech & Rigdon” dies such as this under the mid 400 SN range are thought to be made in Columbus, MS before factory was later moved to Georgia. The revolver, serial number 346, generally follows the pattern of the Colt Model 1851 Navy being .36 caliber with a 6-shot cylinder, 7 ½” part round, part octagon barrel marked on the top flat of the barrel’s octagonal breech “LEECH & RIGD– .” The letters “C.S.A.” are not present either due to a variation in the barrel marking on an incomplete stamp (which is likely because the last two letters of the firm’s name are not visible). Walnut one-piece grips with brass trigger guard and back strap. All marked parts match. In place of the more common 4-dot cross mark on the brass trigger guard, the capital letter “N” is stamped on the left side of the trigger guard. The serial number on the cylinder is unusual and interesting being stamped “346” with an additional “3” above the “4” and an additional “4” below the “3” almost as if the worker could not decide whether to stamp the serial vertically or horizontally. Before the Civil War, Thomas Leech was a cotton trader and Charles H. Rigdon was a scale maker. Together their association would produce for the Confederacy one of the best revolvers of the time that could easily compete with the 1851 Colt Navy, of which it was a direct copy. Thomas Leech is also known to have had other business interests, for some Derringer pistols have survived that are marked “made for Thomas Leech & Co, Memphis, Tenn”. He had also founded the Memphis Novelty Works in 1861, a company specialized in the manufacture of cutlery, in particular, a number of Confederate swords. By May, 1862 the company was known as Leech & Rigdon, and was established at Columbus, Mississippi. The partners secured a contract with the Confederate States Government for the manufacture of 1,500 revolvers of the Colt Navy 1851 type. The Leech & Rigdon Company moved from Columbus in December of 1862 due to the impending Union threat. The manufactory was moved to Greensboro, Georgia; and all efforts were concentrated on the manufacture of revolvers. The partnership dissolved for unknown reasons in December, 1863, with a total about 1,500 revolvers produced. Charles Rigdon bought the company’s machinery and tools, kept the workers and reinstalled the plant at Augusta, Georgia, where he was joined by Jesse A. Ansley and two other partners, with whom he formed the Rigdon, Ansley & Co. The new company would continue to produce revolvers of the same type for the Confederate army. The original Leech & Rigdon’s contract for 1,500 pistols seems to have been achieved, and from serial # 1500 on, the company started the production of guns equipped with a 12 slot cylinders, which are today known as the Rigdon Ansley revolvers. On the back strap appears the name “Thomas Ruddick” which has been hand scratched into the brass. Initial research shows a Thomas Ruddick in the 28th Mississippi Cavalry Regiment, C.S.A. an important Western theater cavalry regiment, a quick glimpse of their history shows that this regiment was organized early in 1862, for three years. The original officers — Starke, Ferguson and Jones — were commissioned February 24, 1862; the regiment was reported May 14 in at Camp at Jackson, where it was organized. Colonel Starke was a man of prominence and had organized a cavalry company in his home county, Bolivar, early in 1861. The first active service of the regiment was occasioned by the naval attack on Vicksburg, beginning in May, 1862. Five companies of Starke’s Cavalry reinforced Gen. M. L. Smith, at Vicksburg, and were posted to watch the flanks along the Yazoo and below Warrenton on the Mississippi. Later the regiment was at Camp Burrus, in Bolivar County. They operated along the river and in the swamp country, where many contracted fever. At Vicksburg in December, 1862, part of the regiment took part in the Chickasaw Bayou campaign, while the remainder of the regiment, according to Federal reports, was engaged with Steele’s expedition from Helena, in the vicinity of Panola, in the same month. In January, 1863, the regiment was assigned Gen. W. T. Martin’s Division of cavalry under General Van Dorn, about 7,500 strong, which fought in the campaign in Middle Tennessee early in 1863, supporting General Bragg’s army. They were present at the battle of Thompson’s Station, March 5, but held in reserve; were in the skirmish with Minty’s Cavalry at Thompson’s Station, March 9, and actively engaged in the attack on Franklin, April 10. Van Dorn’s campaign, during which he lost his life in a private affair, left Mississippi open to Grierson’s raid and Grant’s advance from Bruinsburg to Jackson and the Yazoo River. The Twenty-eighth, leaving Tennessee May 17, reached Mechanicsburg June 7, a march of 400 miles where they attacked a detachment of the Fourth Iowa Cavalry, under Major Parkell. July 4 the regiment moved from Mechanicsburg to Birdsong’s Ferry, and as Johnston’s army fell back to Jackson, they skirmished with Sherman’s advance July 7, and fell back covering Johnston’s retreat, skirmishing frequently and resisting a charge of cavalry at Clinton. Just before the evacuation of Jackson, July 16, they went to the Federal rear, and recrossed Pearl River after the retreat of Johnston to Morton. After the evacuation of Jackson by Sherman, the regiment was at or near Clinton until moved to Brownsville in September. On October 10th detachments from the 28th were attacked, near Port Gibson by a force of Illinois and Wisconsin Cavalry, whose commanding officer reported 11 of the two regiments killed. October 14th McPherson’s expedition set out from Vicksburg intending to go to Canton but on account of the effective resistance made, proceeded no further than Clinton. There were engagements at Brownsville, October 15; on the Canton road near Brownsville, October 15-16; near the Clinton and Vernon cross roads, October 16; at Bogue Chitto Creek, and near Livingston, October 17; and near Clinton, October 18, in which all or parts of the regiment were engaged. After this the regiment was on guard between the Pearl and Big Black Rivers to the close of the year. December 25, 1863, At the outset of Sherman’s raid to Meridian, they met the advance of Hurlbut’s column giving battle there February 4th. This all was preparatory to the campaign against Atlanta. The regiment moved into Alabama in the spring of 1864. May 5, 1864, the brigade moved from Carthage to Montevallo, Ala.; 14th, arrived at Rome, Ga.; 17th, reached Adairsville and engaged the enemy with considerable loss in killed and wounded; May 20, fought at Cassville, crossed the Etowah, and moved to Dallas, skirmishing. May 28 the brigade was dismounted temporarily and put in the trenches on the extreme south of the line extending from northeast of New Hope Church, southwest of Dallas. After this they skirmished continually as the armies moved to the Marietta line, skirmished on that line and in the Federal rear near Powder Springs, picketed the Chattahoochee River, moved to West Point July 17 to meet Rousseau’s expedition, took part in the battle of July 28 near Atlanta, skirmished at Herring’s Mill July 30, was in the battle of August 6, and fought near Jonesboro, August 30. In battle at Lawrenceburg, Campbellsville, Columbia, Spring Hill and Franklin; in November, they followed the Federal army to Nashville, thence moved to Murfreesboro, and was particularly distinguished in battle there December 7. In the rear guard of the army during the retreat from Nashville they fought at Columbia, Warfield’s, Richland Creek, Pulaski, King’s Hill and Sugar Creek, December 22-26. Their commander, Colonel Starke was promoted to Brigadier-General November 4, 1864, and the regiment is assigned to his brigade in General Chalmers’ orders of February, 1865. When Gen. J. H. Wilson started on his raid through Alabama and Georgia in March and April, 1865, the brigade moved from Pickensville, Ala., to meet him, and after three days and nights of marching and countermarching arrived near Selma during the assault upon the fortifications there, April 2, but were cut off from the town by the Federal troops and were unable to render any assistance. When Selma was taken they were compelled to retire in the night, thirty miles, across the Cahawba River, after which they moved to Livingston and went into camp. There the last muster rolls were made, up to April 31, 1865. The capitulation by Gen. Richard Taylor occurred May 4, 1865. The cavalry commands under General Forrest were surrendered at Gainesville, Ala., May 22, 1865. With a long and distinguished history, the relationship between this revolver and this famous cavalry unit is remarkable. Mr. Michel’s Notes State: “Not unlike many seemingly strange partnerships in the arms trade, the pairing of Leech & Rigdon joined a scale manufacturer, Charles H. Rigdon, with a cotton grower, Thomas Leech. Apparently their first arms were produced in Greensboro, Georgia. This revolver, serial number 346, has the typical small numbers and barrel marking “Leech & Rigdon” of the company’s early production. Well marked and completely original, that serial number appears on the cylinder, frame, loading lever, loading lever catch, grips, and backstrap. The backstrap is scratch engraved with the name “Thomas Ruddick”. Ruddick was mustered into service on March 9, 1862, at age 27. He joined Capt. George T. Blackburn’s Company of Cavalry, Starke’s Regiment, Mississippi Volunteers (subsequently becoming Company D of the 28th Regiment of the Mississippi Cavalry). He was apparently taken prisoner at Lake Village, Arkansas, on May 14, 1864. Provenance: Catalog of L. C. “Red” Jackson, No. 9, of September 1960.” PROVENANCE: Catalog of L.C. “Red” Jackson #9 of September 1960. CONDITION: Good. All iron parts have a nice dark grey patina which has never been severely cleaned. There is light pitting at the barrel’s muzzle and near the breach. The revolver’s mechanics are fine. Walnut grips show light wear consistent with the metal surfaces of the gun. All serial numbers match. 4-31350 CW11 (25,000-35,000)

Revised: 10/19/2007

(Correction) In reference to Mr.Michel’s notes it states “Kings of Rythias Hall”. This should actually read “Knights of Pythias Hall”.

FINE CONFEDERATE LEECH AND RIGDON REVOLVER. SN 634. A fine specimen of this rare Confederate revolver made by Thomas Leech and Charles H. Rigdon in Greensboro, GA. The revolver, serial number 634, generally follows the patter of the Colt Model 1851 Navy being .36 caliber with a 6-shot cylinder, 7 ½” part round, part octagon barrel marked on the top flat “LEECH & RIGDON CSA.” Walnut one-piece grips with brass trigger guard and back strap. All marked parts match. The distinctive 4-dot cross appears on the brass trigger guard. On the left side of the barrel breech stamped in large letters is “LAFAYETTE LODGE/25/KP” leading me to believe that this revolver was once the part of a collection of war trophies on display at the Knights of Pythias (KP) lodge. Interestingly, the name was misspelled and a “Y” added to left flat of the barrel breech to correct “LAFAETTE.” This stamping was accomplished at some early period following the Civil War. Mr. Michel’s Notes State: “This Leech & Rigdon revolver is marked on the larger stamping “Leech & Rigdon CSA” on the barrel housing and serial number “634” on the cylinder, frame, loading lever, loading lever latch, grips, and backstrap. Apparently, this revolver was once on display at a Kings of Rythias hall, as the left side of the barrel housing is well marked “Lafayette Lodge / 25 / KP”.” CONDITION: The revolver is quite attractive having an even plumb brown patina on all of the iron parts and a nice mellow color to the brass. Typical casting flaws are noted here and there as is moderate wear. There is a chip missing from the toe of the left grip. The revolver functions mechanically well. A nice opportunity to own a rare Confederate revolver in attractive condition. Some additional research may reveal where the location of the “LaFayette Lodge” was located. 4-31349 CW1 (25,000-35,000)

RARE CONFEDERATE RIGDON, ANSLEY & COMPANY 12 STOP REVOLVER SN 1762. This Confederate revolver, serial number 1762, was produced by Rigdon, Ansley & Company of Augusta GA and is, generally, patterned after the Colt Model 1851 Navy. About 1,000 of these were made in .36 caliber with a 6-shot round cylinder having 12 stops on the exterior. All iron with brass trigger guard and back strap with one-piece walnut grips. A marvelous opportunity to obtain a classic and rare Confederate revolver manufactured in Augusta, GA during the American Civil War. Mr. Michel’s Notes State: “The Rigdon, Ansley & Co. revolvers were basically the same revolvers as those produced by Leech & Rigdon. The most recognizable difference is the adoption of a 12-stop cylinder. When the Leech & Rigdon partnership dissolved, Charles Rigdon moved the plant and formed a new company with Jesse A. Ansley, Andrew J. Smith, and Charles R. Keen under the new name Rigdon, Ansley & Co. Rigdon, Ansley & Co. revolvers begin at about serial number 1500 with the highest serial number known in the 2400 range. This revolver is serial number 1762 and in keeping with other known revolvers in that range is marked on the barrel housing only, “CSA”.” CONDITION: Fine, all iron parts have aged to a pleasing dark brown patina, never cleaned and with only moderate wear. Two cylinder nipples are broken. Brass parts have an equally pleasing patina and the revolver functions mechanically well, however, its ability to stay at full cock is touchy. 4-31351 CW3 (25,000-35,000)

“GARRETT” BRASS FRAME PERCUSSION PISTOL SN 69. Cal. 54. We are calling this pistol a Garrett because most early literature describes it as such, but we do not know definitively who made these guns. They are very well made. Most Confederate handgun collectors try to find one of these scarce pistols. Mr. Michel, in his notes, states the Garrett controversy quite well as follows: “This pistol has long been associated as a Confederate assemblage, but at the same time there have been questions as to its origins and use. Bennet and Simmons in their book, Confederate Handguns, devoted an entire chapter to these pistols, suggesting they were made up by J&F Garrett & Co. of Greensboro, North Carolina, the name by which they have since been known. Garrett was the manufacturer of the Tarpley’s patent breechloading carbine. The association was primarily the result of an effort to identify the pistols referred to in DeBow’s Review, a Southern bimonthly publication, as being among the items being manufactured in 1862 by the Garretts. In all the years that have passed, no one seems to have identified the source of these pistols and in particular how an apparently substantial supply of Model 1842 pistol barrels, ramrods, hammers, and trigger guards came to be in need of assembly with a brass frame and new grips”. Recent research has shown that there were quantities of surplus 1842 pistol parts. The failure rate at Aston & Johnson was quite high. We now believe Palmetto Armory contract 1842 pistols are made from Aston-Johnson condemned 1842 parts, so there is no doubt a quantity of these parts was available. Regardless of who made these pistols, they are scarce, and this is a very presentable example. CONDITION: Metal surfaces are cleaned overall. “JH” proof in bbl is crisp. Metal surfaces are gray, smooth, with scattered pitting. Brass surfaces are cleaned with numerous small scratches and dings. The removable brass panel fits poorly at trigger guard. Stocks retain much of their orig varnish, though scratched and chipped. Hammer screw appears replaced, as does ramrod assembly. 4-31353 JS109 (3,000-5,000)

LEFAUCHEAUX ARMY PISTOL, HOLSTER, CAP BOX, & BELT a most interesting, orig rig in excellent condition. 12mm LeFaucheaux pistol, SN 35315, exhibits 20-30% bright blue finish. Holster, cap box, and belt all in excellent condition. Leather surfaces are very good. Cap box, though it has a brass finial and two sewn belt loops, is not necessarily of U.S. manufacture. It could be Confederate-made. Confederates did copy Union accouterments, and the sewing style could be CS. Cloth belt is most unusual. We have never encountered this double-roller buckle belt before. Mr. Michel, in his notes, describes this rig as follows: “This complete Confederate cavalryman’s outfit includes is LeFaucheaux pinfire revolver, original heavy leather holster, cap box, and red stripe double roller buckle cloth belt. The fit of the revolver to the holster is evident down to the unique impression in the holster of the extractor rod. The cap box, apparently adapted to hold the pinfire cartridges, is of matching hand sewn leather as are the two straps with roller buckles on the belt. The pistol itself shows wear at the muzzle but is in overall very good condition, all complete and serial numbered 35315.” CONDITION: Pistol overall is brown/blue with areas of scattered staining. Stocks retain traces of orig varnish with numerous dents and scratches. Markings are all crisp. Mechanically, gun is fine. Holster is overall complete, intact, supple and surfaces have some scuffed areas to high spots. Cap box is also very good, with good surfaces. Cap box lacks lamb’s wool which could have been purposely removed to hold cartridges. Belt overall is very good, with minor insect damage and a few scattered tears and reductions. One leather end is cracked. Leather tongues are solid but crazed. 4-31375 JS59 (1,000-2,000)

KERR REVOLVER. SN 1493. Cal. approx 44. Mr. Michel, in his notes, describes this gun as follows: “This 5-cylinder revolver is the product of the London Armory Company, with whom Caleb Huse made one of his first contacts in his effort to procure arms for the Confederacy. In addition to stands of longarms, London Armory furnished the Kerr revolvers in significant numbers. Those with Confederate association, as this one, are struck with the ‘JS’/anchor mark, the same as those that appear on the longarms. This mark on the pistol is on the underside of the checkered grips below the trigger guard plate. The lockplate of this revolver is engraved ‘London Armory’ and the frame is marked with the serial number ‘Kerr’s Patent 1493’. This is a particularly fine specimen with considerable amounts remaining of the original fine blue finish”. This is a very fine example of the Blockade Run “JS”/anchor marked Kerr revolver. It is also a very low SN, associated with Confederate Kerrs. CONDITION: Bbl and cyl retain 60-80% orig bright blue finish with areas of scattered staining. Face of cyl has several cuts and dings. Frame and lock retain traces of orig finish. Stocks show little wear, retaining orig varnish. “JS”/anchor markings are crisp, though partially obscured by checkering. 4-31372 JS110 (7,000-10,000)

TRANTER ARMY REVOLVER. Cal. approx. 44. Mr. Michel, in his notes, describes the gun as follows: “The five chambered Tranter revolver is one of several imported English pistols which found favor in the hands of Confederate soldiers. Perhaps the most famous of these revolvers is the one apparently presented to General J. B. MacGruder. This revolver retains traces of its original finish underneath the barrel. It is marked atop the frame ‘Deane & Son / 30 King Willism Stt / London Bridge”. CONDITION: Metal surfaces are gray with scattered areas of pitting and traces of finish. Stocks exhibit traces of orig varnish and numerous small nicks, scratches, and gouges. 4-31373 JS111 (1,500-2,500)

WEBLEY “WEDGE-FRAME” ARMY REVOLVER. SN 2361. Cal. approx. 44. Mr. Michel describes this scarce Confederate import as follows: “The five chambered ‘Wedge-Frame’ Webley double action percussion revolver was, although generally unrecognized as such, a revolver that was imported in some number to the Confederacy. Less well recognized as an imported revolver in the hands of Confederate troops than the more well-known Kerr or Tranter revolvers, these are no less deserving of a place in the panoply of Confederate arms. The top of the frame is marked only ‘London’ and the side of the frame ‘J. Adams’. The left side of the frame is marked ‘Patent No. 2361′”. CONDITION: Metal surfaces are gray/brown with scattered staining and pitting. Traces of finish are found in protected areas. Stocks worn over checking with traces of orig varnish present. Front blade site and wedge are replacements. 4-31374 JS112 (2,000-4,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel describes this gun as follows: “This alteration to percussion is attributed to M. A. Baker of Fayetteville, North Carolina. The alteration is unusual in that instead of brazing a bolster to the bbl, a quarter section was removed from the bbl and a new section with the bolster was brazed back in place. Orig pan is filled such that the small bolster rests atop lockplate. Bbl is clearly marked ‘N. Carolina’. Hammer is the correct, ‘S’-curved shape and this pistol is the only known example that has the orig hammer.” You are bidding on possibly the only North Carolina surcharged Baker, Fayetteville conversion in complete and in superb condition. CONDITION: Metal surfaces are all gray with scattered staining and pitting. Wood is very good, showing orig varnish and inspector’s cartouche. Initials “JB” are carved in stock opposite lock. Lock and bbl markings are all discernible. Hammer screw is a possible replacement. 4-31360 JS183 (4,000-6,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. According to Mr. Michel, “This alteration is by T. J. Adams of Richmond, Virginia. The bolster housing the nipple alteration to percussion is brazed to the bbl and rests with bottom on the orig lockplate. Lockplate has been cleaned of its orig markings and pan removed with the areas filled as a base for the bolster. It is marked with Roman numerals characteristic of Adams’ alterations, except for the hammer, which is marked number ’14’ on the interior surface.” CONDITION: Metal surfaces all cleaned with scattered staining and pitting. Lock is devoid of all markings except for residual “A” stamped near center of plate. Hammer is over-cleaned and recolored. Stock is sound with a couple hairline cracks, scattered scratches and nicks. Residual cartouches are still visible from when inspected as flintlock. 4-31354 JS185 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Mr. Michel describes this Model 1836 pistol as follows: “This alteration to percussion of a Model 1836 pistol is by unknown person or company. Bolster is similar to that used on muskets altered by Union Manufacturing Co. of Richmond, Virginia. Curved bottom of bolster is neatly filled to remnant of orig brass pan. Lockplate has only faint remnants of orig markings.” This gun appears all orig and complete, and it exhibits a most unusual and displayable conversion hammer and bolster alteration. CONDITION: Metal surfaces are all cleaned and pitted overall. Lock and bbl markings are discernible. Stock is sound and cleaned with several dents and scratches. Inspector cartouches are still visible. 4-31362 JS178 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel, in his notes, describes this gun as follows: “This brazed bolster alteration varies from alterations done by Adams in that the bolster is inlet into the lockplate rather than resting atop the plate and is larger than the bolsters employed by Adams. The assembly number ‘6’ is also different from the Roman numerals used by Adams. The lockplate has remnants of the orig markings indicating this pistol was made by Johnson rather than Waters.” You are bidding on an unusual Virginia brazed bolster conversion with an interesting and presentable blacksmith-style hammer. CONDITION: Metal surfaces all cleaned gray/bright and pitted. Markings are well-struck and discernible. Stock has numerous scratches, dings, and gouges, though residual cartouches are present. Mainspring is broken. Hammer screw is a replacement. 4-31358 JS182 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. Mr. Michel describes this gun as follows: “This brazed bolster alteration to percussion of a Model 1836 pistol is similar to the work done by Adams except that the bolster, instead of resting atop the orig lockplate, is inlet into the lockplate. The 3 faceted bolster is similar to the bolster used on alterations of Virginia Manufactory muskets believed to be the work of Francis Persignon of Richmond, Virginia. All parts of this pistol are marked with the combination of Roman numerals found on Adams’ alterations, in this case VI and IX. Lockplate still shows traces of orig. Asa Waters marking.” This pistol appears orig, authentic, and complete in every regard. CONDITION: All metal is cleaned bright with scattered pitting. Because of cleaning, lock markings are weak, as are bbl proofs. Stock is sanded, though sound, exhibiting one hairline crack behind lock. Cartouches are discernible, as are initials carved on right hand side of grip. 4-31356 JS180 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel describes this brazed bbl alteration as follows: “This brazed bbl alteration to percussion of a Model 1836 pistol is attributed to D. C. Hodgkins of Macon, Georgia. Bbl is marked ‘* Pope E. Hill, Waycross Ga *’, the significance of which is unknown, as is the marking around the muzzle of bbl, ‘**Tootsie R***** Mch 18, 1917’. The pitol has been polished bright. Lockplate shows traces of orig Asa Waters markings.” If this pistol could only speak. Who was Tootsie, and what did she do on March 18, 1917? Since this pistol was altered in Macon, Georgia, it didn’t travel a long way in 50 years to get to Waycross, Georgia, where Pope Hill gave this gun to Tootsie R. You are bidding on a rare Confederate alteration with a probable interesting post-war history. CONDITION: All metal parts of this gun are polished bright with inscription as described above. Orig markings, because of polishing, are visible but weak. Stock is sound with a couple hairline cracks, scattered scratches and dents, and residual cartouches from when it was a flint. 4-31359 JS179 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel in his notes describes this Model 1836 U.S. martial pistol as follows: “This alteration to percussion uses a snail-shaped bolster similar to pistols altered by J. P. Murray of Columbus, Georgia, but this pistol does not have the same marking on bottom of bbl, and in bbl channel as has the alteration currently attributed to Murray. Lockplate has been replaced with a civilian-type plate marked ‘O. Mazange & Co. / Mobile’.” This is a very unusual pistol. Not only does it exhibit Confederate alteration, it also exhibits a civilian lock and hammer with a Mobile, Alabama agent. You will never have the opportunity to buy such a rare and uniquely marked gun. CONDITION: Bbl, lock, backstrap, and trigger guard are all brown with scattered pitting. Stock retains orig inspection cartouches when this gun was orig made as a military flint. Loading assembly appears to be restored. 4-31361 JS177 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel describes this pistol as follows: “This pistol is the flintlock Model 1836 altered to percussion by brazing a bolster to the location of the orig touchhole. Brazed bolster and bench assembly marks are similar to those used in the alterations by Adams, but bolster seams are more crudely finished and have a more humped shape. Orig lockplate markings have all been effaced.” You are bidding on a classic, Confederate, brazed bolster conversion that the armory removed all US markings, and this gun is in wonderful, “as found” condition, orig and complete in every regard. CONDITION: Metal surfaces are brown/gray with scattered pitting. Stock retains much of its orig varnish with numerous old scrapes, nicks, and gouges. Residual inspector cartouche is still present. 4-31357 JS184 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel describes the pistol as follows: “Although there is nothing except one’s imagination to classify this pistol as a Confederate alteration to percussion of a Model 1836 pistol, there is something about the hard usage this pistol has seen that speaks of both the necessity of pressing old arms to the service of the Confederacy and the use of local blacksmiths or even gunsmiths to convert these old guns to meet the immediate need to arm the troops. This pistol has been altered skillfully using the side drum method, well-filled into the area of the pan. It is cracked through the wrist and a large section of wood is broken away above the lockplate.” This gun does appear to be a well-used percussion pistol with a typical, blacksmith conversion and hammer. CONDITION: Metal surfaces with exception of ramrod assembly are dark, pitted, and as found. Lock and bbl markings are well struck and discernible. Ramrod assembly appears restored and is gray/brown and pitted. Stock has large, unrepaired crack through wrist and a 2-1/2″ x 1/2″ piece missing behind lock at breech. Stock retains residual cartouches. Mainspring is broken. 4-31363 JS181 (3,000-5,000)

CONFEDERATE ALTERATION OF MARTIAL FLINT PISTOL. SN NSN. Cal. 54. Mr. Michel describes this gun as follows: “This alteration of a flintlock Model 1836 pistol to percussion was done by T. J. Adams of Richmond, Virginia. The alteration is by use of a brazed bolster which, at the bottom, rests on the lockplate where the cut out for the original flintlock pan has been filled to make a solid base for the bolster. The lockplate shows traces of the orig A. Waters markings. The swivel ramrod is a replacement. The internal parts are marked with the Roman numeral ‘XII’ which also appears at the tail of the left flat opposite the lock.” CONDITION: Metal surfaces, with exception of ramrod assembly, are gray/black and pitted. Lock markings are still discernible. Bbl proofs are mostly obscured. Loading assembly and hammer screw are replaced. Stock is solid with residual cartouche and some remaining varnish. Roman numeral ‘XII’ is cut into stock opposite lock, and a thin 1″ piece of gold is inlaid adjacent to the Roman numeral. 4-31355 JS186 (3,000-5,000)

DOUBLE BARREL SHOTGUN PISTOL. SN NSN. Approx. 24 ga. This is amost unusual, “attic” condition weapon you will see. Mr. Michel, in his notes, states: “Double barrel caliber 58 pistol with unmarked lockplates. While there is absolutely nothing of Confederate manufacture about this pistol, it is precisely the sort of weapon a Confederate cavalryman, lacking a good Colt pistol, would put to use in unseating his opponent. Interestingly, the long tang of the breech ends in a screw hole replaced with a loop, perfect for the attachment of a leather thong to suspend this weapon at the owner’s side. Another hole also appears at the end of the stock where apparently another loop at one time wore away the surrounding wood”. CONDITION: Gun appears in “as found” condition. Metal surfaces are gray/brown with scattered scratches and pitting. Brass surfaces have patina in deep areas. 4-31376 JS106 (500-1,000)

CANTON FROM CONFEDERATE FIRST NATIONAL FLAG. Blue silk canton, approx. 42″ x 43″, with 12 white silk stars, was orig in The Catalogue of America’s War Museum in 1899. This flag was displayed as Gunther No. 4, “Rebel Flag from the first design”. This flag was in the Chicago Historical Society, deaccessioned in the late 1960s. Photos exist of this flag complete, but only the canton remains today. On edges of canton, you can clearly see the disintegrating red, white, and red, stripes. Howard Madaus, in his report on this flag, states: “On Monday of this week I delivered to Mr. Thomas Welter…the remaining fragments of the red and white striped of the 1st National Confederate flag, of which you obtained the canton. After measuring the surviving pieces (which were lacquered in 1936), I have determined that the flag extended 64 inches beyond the canton. As you can see from the enclosed photographs taken shortly after the flag was opened, the lacquering caused the central section of the bars to deteriorate; surprisingly, however, the fly portion remains in good condition…” Mr. Michel’s Notes State: “Blue canton with eleven white stars. This canton was once part of a First National Flag of the Confederacy. It was part of the Gunther collection deaccessioned by the Chicago Historical Society. Photos exist of the complete flag, but only the canton remains as the three stripes disintegrated into small fragments from age and, presumably, poor storage. According to the ”Catalogue of America’s War Museum“, 1899, this flag was displayed as Gunther No. 4, “Rebel flag from the first design.”” PROVENANCE: Ben Michel collection. CONDITION: 1-1/2″ wool hoist is solid. Silk canton and stars show numerous cracks and tears, but for the most part, canton is complete. Flag was not unframed to examine mounting. 4-31455 JS171 (5,000-8,000)

Revised: 10/19/2007

(Additional Information) We have been told by one saddle collector that they question the originality of the CS shield on this saddle. Subsequent research reveals that the shield is Zinc and antique and identical to that which is illustrated on pp.156 of Confederate Saddles and Horse Equipment by Ken R. Knopp. We therefore guarantee that the shield is original, old and genuine; the saddle is definitely old and genuine; however we cannot, and will not guarantee that the shield has always been with this saddle.

CONFEDERATE MCCLELLAN SADDLE WITH “CS” SADDLE SHIELD This saddle is a Confederate Arsenal copy of the Regulation Model 1859 McClellan saddle, having a 2″ pewter shield with raised letters “CS” attached to front of tree. Rawhide, split, open seat with brown leather skirts, cinch straps, and stirrup straps. Small, solid brass stirrups are attached. There are some leather repairs around front of rawhide tree to repair splits in the rawhide. One leather repair goes over 1/2″ of the saddle shield. Skirts appear orig and are attached with brass screws. Cinch straps appear orig. Cinch itself has been replaced with smaller leather strap. “CS” marked Confederate McClellan saddles, such as this one, are very rare. We can find no more than 3 or 4 in private and institutional collections. This is a rare opportunity to own the best marked Confederate saddle available. CONDITION: Rawhide is fairly sound with splitting and openings at sewn edges. Wood is exposed in front of tree. Seat is worn, but seat hardware is intact along with the finely patinaed pewter “CS” saddle shield. 4-31378 JS173 (15,000-25,000)

CONFEDERATE MCCLELLAN SADDLE. Confederate copy of a McClellan cavalry saddle with rawhide, split, open seat, black leather skirts, cinch straps, stirrup straps, and stirrup hoods. This barebones Confederate copy lacks slots for attachment of valise or bed roll. PROVENANCE: Ben Michel collection. CONDITION: Rawhide seat has openings at sewing along front of tree, along with stitch losses on back of saddle behind tree. Skirts are intact, attached with brass screws. Cinch straps on one side are broken off. Stirrup straps appear replaced, as do iron, leather-hooded stirrups, though they are old. One stirrup strap has English maker’s mark. 4-31379 JS174 (3,000-5,000)

CIVIL WAR ERA HOPE TEXAS SADDLE. This distinctive saddle with the broad, flat horn was one design by Adolphus Hope in Texas, probably in the 1830s. Hope continued to make saddles well into the 1850s, but his pattern was copied throughout Texas, and many military people liked the style and continued to use them, especially in the South. At the beginning of the Civil War, some Confederate officers sought out Hope saddles for themselves and their mounted troops. The most characteristic feature of a Hope saddle is the massive, broad, flat saddle horn, covered in rawhide for durability. This example has long skirts, which is atypical, but skirts and seat are decorated in floral designs, typical of Texas decorated saddles. This saddle is accompanied by a set of saddle bags that were found with it. PROVENANCE: Ben Michel collection. CONDITION: Saddle is in very good condition, apparently with all orig parts. Some seam separation is apparent. Leather surface is very good. Skirts are crazed and mottled. Decorations are still strongly detailed. Most iron and brass attachments are intact. Major seams of saddle are sewn with leather cord and are intact. Cinch, wooden stirrups and stirrup straps are intact. A quarter-size brass rosette with horseshoe design at back of seat is typical of rosettes excavated in battlefield sifts and campgrounds. Saddle bags are sound and pliable. Each bag is closed with 3 straps with roller buckles. Three of the roller buckles are missing, as three of the straps are also broken. Cloth linings of saddle bags are sound. Surfaces are crazed and mottled, with one bag being particularly soiled, with stitching coming loose. Saddle bags still display well with saddle. 4-31382 JS172 (2,000-4,000)

CONFEDERATE USED SOUTHERN PLANTATION SADDLE. This saddle is one of two saddles recovered from a Gettysburg, Pennsylvania barn sale. As Mr. Michel states, “this saddle is typical of the type of ‘useful souvenir’ taken by the citizens of Gettysburg after the battle.” This particular saddle is one of numerous variations of plantation saddles popular throughout the South. It has a brown, leather seat and skirts mounted on a horsehair-filled, cloth body. Brass and iron tacks attach seat to saddle tree and sewn body. Stirrup straps appear orig and contain typical 19th century iron stirrups. Cinch straps also appear orig. CONDITION: Overall saddle is good. 1-1/2″ x 1/2″ hole in top of seat is apparently caused by insect or vermin. Surfaces of leather are scraped and scuffed. Several iron and brass tacks are missing. 4-31381 JS175 (2,000-4,000)

CONFEDERATE USED PLANTATION SADDLE. This saddle was recovered from the same Gettysburg, Pennsylvania barn sale as Lot #1138, and Mr. Michel states, “This is the type of ‘useful souvenir’ taken by the citizens of Gettysburg after the battle.” This saddle consists of black leather seat and decorated skirts and horsehair-filled cloth body. cinch straps are probably replaced, as is cinch. Cinch straps are also repair for continued use. CONDITION: Leather surfaces are good, with scuffing and wear at high areas. Geometric decoration is visible on seat and skirts. Cloth saddle body has several large tears, exposing horsehair. Stirrup straps and iron stirrups are sound, though probably replaced. Cinch shows numerous repairs for continued use. 4-31380 JS176 (2,000-4,000)

AUGUSTA ARSENAL CARTRIDGE PACK. For packs of Confederate cartridges, this pack is in remarkably fine condition. Ten orig cartridges and caps will be found in this paper-wrapped, string-tied pack with paper label which reads: “TEN CARTRIDGES, / FOR / Enfield Rifle and Minnie, / OR RIFLE MUSKET / Cal. 57 & 58 / AUGUSTA ARSENAL, GA. / Nov. 1864”. Mr. Michel’s Notes State: “Full packet of Confederate Augusta Arsenal cartridges. Pasted on label reads, “Ten Cartridges / for / Enfield Rifle and Minnie / or Rifle Musket / Cal .57 or .58 / Augusta Arsenal Ga / Nov 1864”.” PROVENANCE: Ben Michel collection. CONDITION: 4-31437 JS85 (5,000-8,000)

RICHMOND ARSENAL CARTRIDGE PACK WITH ORIGINAL GARDNER CARTRIDGE. Very rare Confederate cartridge pack, orig containing Gardner cartridges, the one retained with this pack has cracked paper exposing powder, otherwise is complete. Reformed and tied pack has pasted label that reads “10 cartridges cal 577 or 58 / Richmond Arsenal 186_”. Gardner cartridges are very rarely offered, and due to their fragility, few survive. This is the only pack that we have seen, and though soiled and worn, it is still a very attractive grouping. Mr. Michel’s Notes State: “Brown color paper packet with glued label. Pictured in Salamander Book, ”Fighting Men of the Civil WarMr.“ by William C. Davis, p. 54.” PROVENANCE: Ben Michel collection. CONDITION: 4-31434 JS79 (3,000-5,000)

MACON ARSENAL MISSISSIPPI RIFLE CARTRIDGE AND PACK. In this display, there is an orig Macon Arsenal rifle cartridge from this pack or a similar pack. The pack is very fragile and has a pasted label that reads “10 Mississippi rifle cal. 54 / Conical Ball / Mason Arsenal / 1862”. This pack appears orig and unopened with several small, glued repairs to edges. Mr. Michel’s notes read: “The packet is empty and has been reformed to its original appearance”. If this pack has been reformed and brought back to its orig appearance, a master restorer did this using similar cartridges instead of stuffing it with cotton or paper like most reformed packs. We believe this pack is full of orig cartridges, but we are basing our estimate on Mr. Michel’s notes. Mr. Michel’s Notes State: “Brown color paper packet with glued label reading, “10 / Mississippi Rifle / Cal .54 / Conical Ball / Main Arsenal / 1862” with one of the cartridges from the packet. Packet is empty and has been reformed to original appearance. Pictured in Salamander Book, ”Fighting Men of the Civil War“ by William C. Davis, p. 55.” PROVENANCE: Ben Michel collection. CONDITION: 4-31433 JS84 (3,000-5,000)

FAYETTEVILLE ARSENAL CARTRIDGE PACK. This display contains an orig .58 cal Fayetteville minie cartridge, complete and in nice condition, along with an orig pack of caps, and the orig paper wrapper (salmon-colored), reformed to its orig appearance and retied with its orig string. Though unmarked, this cartridge and pack is known to be a product of the Fayetteville arsenal among cartridge collectors. Mr. Michel’s Notes State: “Salmon color paper packet (empty) reformed to original appearance with one of the paper wrap cartridges from the packet and caps from the packet.” PROVENANCE: Ben Michel collection. CONDITION: 4-31435 JS79 (1,000-2,000)

ENFIELD CARTRIDGE PACK. Orig Enfield cartridge pack is accompanied by a single cartridge and pack of caps. Boxwood Enfield bullet has base mark of “57”. These bullets are commonly excavated with same base mark throughout battlefields of both Eastern and Western armies. Cartridge pack is stenciled, “1860 / for / Rifle Musket/63 / Bullet .55 Diar. / Wax – / Powder 2½ Drs. / WOOD PLUG”. Cartridge pack is empty but reformed and retied with its orig string. Mr. Michel’s Notes State: “Enfield cartridge packet. Brown paper stenciled in black, “1860 / Rifle Musket / 53 / Bullet .55 Diam / Wax / Powder 2½ Drs. / WOOD PLUG” with caps and cartridge.” PROVENANCE: Ben Michel collection. CONDITION: 4-31436 JS82 (1,000-2,000)

LYNCHBURG ARSENAL CARTRIDGE PACKET. This display contains a complete and perfect Lynchburg Arsenal cartridge, a loose 3-ring minie ball, and a paper containing orig caps from the packet, and the orig red/brown paper wrap of the orig 10-cartridge packet. Orig paper has had a form placed inside such that paper could be rewrapped and given the appearance of a full pack. It is retied with orig string. Though this packet is unmarked, it is known to cartridge collectors as a product of the Lynchburg Arsenal. Mr. Michel’s Notes State: “Brown paper packet (empty) reformed to original appearance with one of the paper wrap cartridges from the packet, a bullet from the packet, and caps from the packet. Pictured in Salamander Book, ”Fighting Men of the Civil War“ by William C. Davis, p. 54.” PROVENANCE: Ben Michel collection. CONDITION: 4-31432 JS80 (1,000-2,000)

CONFEDERATE SHARPS CARTRIDGE. This cartridge is out of a complete pack of Confederate-manufactured Sharps. A photograph of an orig pack of Confederate Sharps is shown on back side of case holding this cartridge. Cartridge appears complete and intact. Mr. Michel’s Notes State: “Cartridge is all complete and intact with photo of original packet from which it came.” PROVENANCE: Ben Michel collection. CONDITION: 4-31439 JS75 (200-400)

CONFEDERATE .52 CALIBER RINGTAIL SHARPS CARTRIDGE Mr. Michel’s notes state the paper tail of cartridge is torn and powder is removed and replaced with cotton for presentation. This is a very scarce example of a Confederate Sharps cartridge. CONDITION: 4-31443 JS74 (200-400)

COLUMBUS ARSENAL ENFIELD CARTRIDGE. Nice, complete paper cartridge with minie from orig pack marked “Columbus Arsenal, 1864 for Enfield Rifle and minie for rifled musket .577 caliber”. Cartridge is in very good condition; however, small crack near tail allows grains of powder to escape in display. Mr. Michel’s Notes State: “Cartridge is all complete and intact with photo of original packet from which it came.” PROVENANCE: Ben Michel collection. CONDITION: 4-31441 JS77 (200-400)

ENFIELD RIFLE CARTRIDGE FROM AUGUSTA ARSENAL. Complete English-style Confederate made Enfield cartridge in good condition overall still retains wax on surface of paper around ball. Orig pack from which it came is pictured on back of display. Label said “For Enfield rifle and minnie or rifled musket, cal 57 and 58, Augusta Arsenal, Georgia, 1864”. Mr. Michel’s Notes State: “Cartridge is all complete and intact with photo of original packet from which it came.” PROVENANCE: Ben Michel collection. CONDITION: 4-31440 JS78 (200-400)

CS LABORATORY NAVY PISTOL CARTRIDGE PACK. This display contains paper stenciled over wood block, still discernible is “cartridges / __lts Navy Pistol / CS Laboratory / Richmond, VA”. One perfect cartridge is displayed and four fragment cartridges are still in pack. Mr. Michel’s Notes State: “Wood packet for navy pistol cartridges. Packet with paper over wood block, stenciled, “Cartridges / Colts Navy Pistol / CS Laboratory / Richmond Va” with one complete and intact cartridge and other cartridge fragments.” PROVENANCE: Ben Michel collection. CONDITION: 4-31430 JS87 (2,000-4,000)

RICHMOND CONFEDERATE STATES ARMORY NAVY PISTOL CARTRIDGE PACK. This wood block with pasted label unfortunately is only about 3/4 complete. It still retains 4 broken cartridges. Label reads “(Si)x cartridges / for / (COL)T’S Navy Pistol / made at the / (Labora)tory of Confederate States Armory / Richmond, Va”. Mr. Michel’s Notes State: “Wood block with pasted on label. End is broken off but label reads, “(Si)x Cartridges / for / (Col)t’s Navy Pistol / made at the / (Labora)tory of Confederate States Army / Richmond Va”. Pictured in Salamander Book, ”Fighting Men of the Civil WarMr.“ by William C. Davis, p. 55.” PROVENANCE: Ben Michel collection. CONDITION: 4-31429 JS88 (2,000-4,000)

CS LABORATORY PACKET FOR ARMY PISTOL CARTRIDGES. In this display are two .44 cal. CS laboratory pistol cartridges, both with broken papers and missing powder. The orig wood block for 6 cartridges is also contained in display with partial label where the only discernible text is “6 cart” and a few other letters. Mr. Michel’s Notes State: “Packet with paper over wood block. Only fragments of paper remain but size and remnant of stenciling establish this is the correct packet for the “Army Pistol”. With two cartridges. One is intact, the other has broken paper.” PROVENANCE: Ben Michel collection. CONDITION: 4-31431 JS86 (1,000-2,000)

LYNCHBURG ARSENAL CARTRIDGE. .58 cal, 3-ring minie ball is exposed and broken paper cartridge from an orig Lynchburg Arsenal pack. Only ball and large remnants of paper remain. Mr. Michel’s Notes State: “Broken condition.” PROVENANCE: Ben Michel collection. CONDITION: 4-31475 JS78 (200-400)

.56 CAL COLT MUSKET CARTRIDGE. Mr. Michel’s notes state this cartridge was manufactured at Selma, AL arsenal. Casing for bullet is made of gut. Mr. Michel’s Notes State: “This cartridge manufactured at Selma Arsenal. All complete and intact.” PROVENANCE: Ben Michel collection. CONDITION: 4-31442 JS73 (200-400)

CONFEDERATE LABORATORY .44 ARMY PISTOL CARTRIDGE. This cartridge is complete and in fine condition showing nicely patinated lead and delicate string still tying paper and powder to lead. Mr. Michel’s Notes State: “Paper cartridge string tied to bullet cartridge is all complete and intact.” PROVENANCE: Ben Michel collection. CONDITION: 4-31445 JS76 (200-400)

MORSE CARTRIDGE. Approx. 50 cal. Morse brass cartridge with excavated Confederate .50 cal Morse inserted. Morse cartridges of any configuration are quite scarce, and this will display nicely with any Morse firearm. Mr. Michel’s Notes State: “Cartridge complete with removable ring and primer cap. No powder. Bullet inserted into body.” PROVENANCE: Ben Michel collection. CONDITION: Excavated bullet fits loosely, as brass is of slightly larger caliber. Papier mache flange which holds cap is removable. 4-31444 JS72 (300-500)

CONFEDERATE CARTRIDGES AND POWDER FROM PORT HUDSON. In about a 4″ x 3″, Richmond, Virginia tobacco tin is contained portions of two or three cartridges and a vile of black powder, complete with a tag that reads: “Confederate cartridges and powder from Port Hudson, LA, July 1863”. Bullets contained are two 69 cal. buck-and-ball and a 69 cal. 3-ring minie. Mr. Michel’s Notes State: “Old Edgeworth Tobacco “Plug Slice” tin (Larus & Bro. Co. of Richmond, Virginia) with cartridge fragments, vial of powder labeled “Port Hudson Powder” and old label reading “Confederate Cartridges & Powder from Port Hudson, La July 1863”.” PROVENANCE: Ben Michel collection. CONDITION: 4-31476 JS71 (200-400)

LEMAT PISTOL BULLET MOLD. Very rare LeMat pistol mold. This is a typical LeMat mold with triple cavity. One for the rifle pistol ball and 2 for shot for the grapeshot bbl. This mold is SN 18 on the iron sprue and has an oval maker’s cartouche inside mold which is no longer easily discernible. Since these molds are so rare and generally only come with very low SNs, some authorities have guessed that these molds were only issued with the First Model revolvers, so this mold would have probably been issued with SN 18 LeMat revolver. Mr. Michel’s Notes State: “Three-cavity mold casting 2 round balls and 1 conical ball. Casting would result in 9 balls for cylinder and 18 round balls for the ‘buckshot’ barrel. (See mold pictured in Doug Adams’ ‘The Confederate Le Mat Revolver’, p. 35.) This is evidently the mold for the First Model LeMat revolver and is lightly stamped with number ‘18’ on one sprue cutter.” PROVENANCE: Originally sold by Robert Miller of N. Virginia in 1960s. He sold it as an early battlefield recovery from the Battlefield of the 2nd Manassas CONDITION: Iron sprew and retaining screw are pitted overall. Brass body is cleaned. Uncleaned areas have deep patination and pitting. The SN is discernible but light in sprue. Maker’s cartouche is visible but not readable inside cavity 4-31377 JS97 (3,000-5,000)

ENFIELD .577 CALIBER BULLET MOLD. This well-made, brass, scissor-type, Enfield mold is stamped “25” meaning “25 gauge” with translate in American cals. to .577″. Mold is complete with removable iron base plug and set screw. Mr. Michel’s Notes State: “Brass mold for cal. .58 or .577 solid bullet with plug insert marked “25”.” PROVENANCE: Ben Michel collection. CONDITION: Mold is very good overall, showing filing and tool marks on one arm. Iron surfaces are gray/black with some staining and pitting to set screw. 4-31452 JS99 (300-500)

BRASS MOLD FOR .58 CALIBER, 3-RING MINIE. This very unusual brass mold casts a 3-ring minie from the base on its side. Mold is now missing the base plug which it would have required to make the cavity. Mold shows Southern-style finishing marks and casting flaws, and mold was possibly Confederate-made. Bullet made here appears to be what bullet collectors call a “Confederate high ring, 3-ring minie”. These bullets are typically found in certain battle and camp sites of the Army of N. VA and are quite scarce. Mr. Michel’s Notes State: “Brass mold for .58 or .577 caliber bullet. Casts three-ring bullet.” PROVENANCE: Ben Michel collection. CONDITION: Surface is well-patinated. Overall, very good condition. 4-31453 JS105 (300-500)

BULLET MOLD FOR .64 CALIBER ROUND BALL. Single cavity, scissor-type, iron bullet mold. Mr. Michel’s notes state it was for a Hall’s rifle, and it appears to be the correct .64 cal. for a Hall. PROVENANCE: Ben Michell collection. CONDITION: Gray/black metal surfaces with scattered pitting and staining overall. 4-31454 JS96 (50-75)

BRASS MOLD FOR CASTING ENFIELD-STYLE BULLET AND TWO SMALL ROUND BALLS. This crudely-made mold has a well-finished interior to cast a combination of 1 smooth-sided .58 caliber bullet and 2 shot, approx. .36 cal. If there were ever a mold, unmarked, that we could say was Confederate, this would be it. The Enfield bullet made by this mold was poured from the top, and so would have had a sprue cut from the top. Similar bullets are found in Confederate camp and battle sites. Mr. Michel’s Notes State: “Crudely made exterior but well finished mold to cast a combination of a .58 or .577 caliber bullet and two approximately .36 caliber balls (to make up a buckshot or buck and ball cartridge?)” PROVENANCE: Ben Michel collection. CONDITION: Pin in mold appears replaced. Base plug for bullet is missing as is set pin for mold. Mold is cleaned in areas, but most of surface has deep, rich patina over scattered dings and scratches. 4-31451 JS104 (300-500)

.44 CALIBER PISTOL MOLD. Solid brass scissor-type mold retained by very crude iron, peened-over pin, produces an approximate .44 cal. smooth, conical ball and a round ball. The number “42” is stamped on one of the arms. Mr. Michel’s notes state: “Brass mold casting either a cal .44 conical bullet or a cal. 44 round ball. These molds are believed to be made by the manufacturers of Confederate handguns.” Regardless if this mold is Confederate manufactured or not, similar bullets produced by this mold are commonly excavated in areas occupied by Confederate cavalry. CONDITION: This mold has seen some use. Numerous small dings and dents are found throughout its surface. 4-31447 JS100 (300-500)

BRASS SIDE POUR .58 OR .577 CALIBER 3-RING BULLET MOLD. This mold has many English features in the way it was made, but shows casting flaws typical of Confederate manufacture. “Potts” is stamped onto one handle. Bullet produced by this mold is typically found excavated in Confederate infantry sites. Mr. Michel’s Notes State: “Mold for side pour of 3-ring cal. .58 or .577 bullet. One of handles stamped, “POTTS”.” PROVENANCE: Ben Michel collection. CONDITION: Mold overall is very good with scattered dings, dents, and scratches. Pin is pitted. Brass surface retains rich patina throughout. 4-31449 JS101 (300-500)

BRASS BULLET MOLD FOR 2-RING BULLET. Very unusual, well made, solid brass mold for 2-ring, flat based bullet, possibly for carbine. Mold appears to be about .58 caliber. Both arms of mold are marked “CAK”. “CAK” is possibly an inspector, as this mold is so well made. Mr. Michel’s Notes State: “Brass mold casting 2-ring .58 or .577 caliber bullet. Both handles stamped with initials “C A K”.” PROVENANCE: Ben Michel collection. CONDITION: Brass surfaces overall are very good, with scattered dings and scratches. Other wise brass has good patina with some staining. Iron screw at pivot is pitted. 4-31450 JS98 (300-500)

.69 CALIBER ENFIELD MOLD. Typical English-style scissor mold made of solid brass with attached iron sprue cutter. Under spruce cutter, mold is marked “16” which would have corresponded to 16-gauge, or .662″, which would have probably made a ball for a .69 cal. rifled musket. This mold is complete with base plug and set screw. This is a scarce mold. Bullets from molds like this are commonly found in early war Confederate sites. Erroneously stamped on the side of this mold is “.577”, which would have been for a standard 25 ga. mold. How that marking got here is anyone’s guess, but it appears contemporarily to the Civil War. Maybe this is the reason this mold was exported to the Confederacy. CONDITION: Brass surfaces are well-patinated over surface scratches and dings. Iron screws and sprue cutter have scattered pitting. 4-31448 JS103 (300-500)

BRASS BULLET MOLD FOR .36 CALIBER PISTOL. Solid brass, scissor-type mold with double cavity for .36 cal. conical ball and .36 cal. rnd ball. This mold is retained by a brass pin. Number “52” is partially cast into 1 arm, and initials “HW” OR “MH” are cut inside one arm. Mr. Michel’s notes state: “Brass mold casting either a .36 cal. conical bullet or a .36 cal. round ball. These molds are believed made by the manufacturers of Confederate handguns.” Bullets like these are commonly excavated from Confederate battle and camp sites. CONDITION: Brass surfaces have been cleaned. Numerous file marks are present on surfaces. Numerous dents and dings are present on most surfaces of this mold. 4-31446 JS102 (300-500)

Revised: 10/19/2007

(Correction)This tool is actually a pattern “4”, not a pattern “3”.

ENFIELD COMBINATION GUN TOOL. This particular gun tool could do most anything to a Enfield rifle or musket. There are commonly excavated, complete or just pieces. Theoretically, the sgt of each Enfield armed co would have such a tool. Tool contains screwdriver, mainspring wrench, various worms, extractors, and oiler. This particular tool is complete and in very good condition. Mr. Michel’s notes state that this is an English Pattern No. 3 Sgt’s Gun Wrench of 1858. CONDITION: Tool retains much of its orig finish and does not appear to have been used. 4-31321 JS95 (300-400)

CONFEDERATE FOOT OFFICER’S SWORD WITH CAST “CS” IN HILT. This Confederate copy of a Model 1850 foot officer’s sword exhibits a 1″ oval with “CS” cast into hilt, opposite floral decoration. Foliate decorations surround the “CS” medallion. A large flower is cast into bottom guard. Several different makers are known to have made these swords, including Leech & Rigdon of Memphis, Tennessee and other locations; Conning of Mobile, Alabama; and others. We feel this sword is probably made in Mobile by Conning or another maker due to the style of blade. Blade is half-round on spine and cutting edge at ricasso, which is typical of Conning. This blade is very lightly etched in about a 12″ panel on both sides of blade. Only scattered floral motifs are visible in this etching. Grip is leather-wrapped with twisted brass wire. Scabbard is brass-mounted, back sewn leather. Scabbard mounts are retained with screws on back side. Mr. Michel’s Notes State: “Confederate foot officer’s sword. Single, unstopped, fuller blade. Scabbard has leather replaced. Mounts are original.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with traces of etch visible. Grip retains about 90% of orig leather with all its orig wire. Hilt and brass wire retain rich patina. Scabbard mounts are cleaned. Scabbard leather is replaced. 4-31390 JS11 (4,000-6,000)

CONFEDERATE CAVALARY SABER. This sword is possibly a product of Louis Froelich at the Confederate States Armory in Kenansville, North Carolina. Most Froelich products exhibit the classic Froelich hilt and flat, plain pommel, where this sword exhibits Confederate-made 1860-style hilt. Blade and scabbard are very similar, if not identical, to other known Kenansville products. Blade is classic, unstopped, fullered, and 35″ long. Scabbard is lap seamed with pinned throat, typical of other known Froelich products. Grip is leather covered with single brass wire wrap. Mr. Michel’s Notes State: “This Confederate cavalry saber has yet to be identified as to the manufacturer. While it is somewhat crudely made, it is certainly a serviceable weapon capable of doing as much damage as its better made contemporaries. The counterguard has a casting flaw hole. The guard does not appear to be marked in any fashion, nor does the scabbard. The scabbard is typical of most all of these swords, crudely brazed at the seam and mounted with brass rings and a brass throat piece.” PROVENANCE: Ben Michel collection. CONDITION: Blade is bright with old sharpening and scattered areas of staining. Scabbard retains a portion of its orig brown coating. Grip retains about 10% of its orig leather and two turns of its orig copper wire. Brass hilt and scabbard mounts exhibit nice mustard patina. 4-31393 JS2 (3,500-5,500)

CONFEDERATE FOOT OFFICER’S SWORD. This is a nice example of a New Orleans-made foot officer’s sword, probably by Thomas, Griswold & Co., New Orleans, though unmarked. 29-1/2″, pen knife-style blade is hand-forged and shows areas of orig polish. Grip is highly polished brown leather with twisted wire. Hilt is a copy of U.S. 1850 foot. Orig, red cloth, protective washer is intact. Backstitched leather scabbard exhibits scalloped middle and top brass mounts. Scalloped scabbard mounts are distinctive to Griswold & Dufihlo of New Orleans. Mr. Michel’s Notes State: “Confederate foot officer’s sword. Single fuller blade with curved stop at ricasso and “pen kife” cut for blade. Appears to be product of Thomas Griswold & Co., New Orleans, Louisiana.” PROVENANCE: Ben Michel collection. CONDITION: Sword overall appears untouched. Blade is gray/bright with scattered areas of staining and pitting, especially at tip. Grip retains 90%+ of orig shine with scuffing at high areas. Brass hilt and top two brass scabbard mounts exhibit nice patina. Top mount has several dents. Drag appears replaced. Leather scabbard body is dry and hard. 4-31387 JS7 (4,500-6,500)

FOOT OFFICER’S SWORD. 31″ “pen knife” style blade is typical of New Orleans and French made swords. Blade shows remnants of etching on ricasso and spine. Blade is hand-forged, showing uneven fullers and waves in blade. Brass hilt is a copy of a Model 1850 foot. Scabbard is brass mounted, back sewn leather. Mr. Michel’s Notes State: “Confederate foot officer’s sword. Small fuller blade with unstopped fuller and “pen knife” cut for blade.” PROVENANCE: Ben Michel collection. CONDITION: Leather grip and wire wrap are very good and complete, exhibiting wear only at high spots. Brass hilt exhibits nice patina. Blade is gray with areas of pitting, old grinding, and recoloring. Scabbard is a reproduction. 4-31388 JS5 (1,000-2,000)

CONFEDERATE FOOT OFFICER’S SWORD. This Confederate sword was possibly made in New Orleans. We believe this to be a New Orleans-made sword due to the split pommel and scalloped scabbard mounts. Though the sword blade is not typically New Orleans, it is a classic, hand-forged, 30″, unstopped, fullered blade. The blade is hand-forged, showing the typical waves in the blade. Mr. Michel’s Notes State: “Confederate foot officer’s sword. Single, unstopped, fuller blade. Appears to be product of James Conning of Mobile, Alabama. Scabbard has leather replaced. Mounts are original.” PROVENANCE: Ben Michel collection. CONDITION: Brass hilt still retains strong traces of orig gilt. Blade is gray/bright with areas of staining and pitting. Tip of blade is bent. Grip leather and wire appear replaced. Scabbard leather is replaced, though mounts appear orig. Scabbard mounts have been cleaned, polished, and recolored. 4-31389 JS10 (3,000-5,000)

CONFEDERATE-USED FOOT OFFICER’S SWORD. This sword appears untouched and is a typical “attic” find. We cannot ascertain who made this sword, whether it was Confederate or imported; however, the scabbard has several features which could be Confederate manufactured, especially the hand-sewn frog. Sword exhibits 31″, flat, hand-forged blade. Guard is simple, brass “P” guard with a single extra branch. Grip lacks wire. Grip exhibits a 3/4″, decorated brass ferule and crudely cast, mushroom-shaped pommel. Scabbard is backstitched with brass drag and single brass carrying ring with frog attached by brass wire. CONDITION: Blade is gray with scattered areas of staining and pitting. Brass hilt and brass scabbard mounts exhibit good patina. Leather scabbard and frog are crazed with scuffing and loss of black surface. 4-31391 JS9 (1,000-2,000)

CONFEDERATE CAVALRY SABER MANUFACTURED BY LOUIS FROELICH AT THE CONFEDERATE STATES ARMORY, KENANSVILLE, NORTH CAROLINA. Classic 35-1/2″ unstopped, fullered blade. Classic flat, plain pommel and guard exhibiting Roman numberal “VI” cut into hilt and matching Roman numeral cut into top of scabbard throat. Hilt has casting flaws. Scabbard is iron, lap seamed, and braised with brass mounts. Grip is leather covered with iron wire. Mr. Michel’s Notes State: “Cavalry saber manufactured by Louis Froehlich of Kenansville, North Carolina. The 35½” blade has an unstopped fuller from about ¾” from the guard to 7½” from the top. The blade is uncleaned with only age staining. The plain pommel 3-branch guard is typical of this manufacture and has the Roman numeral “VI” cut into the edge of the brass throat of the scabbard. The scabbard is of iron, somewhat crudely seamed, with brass ring mounts. There is a crack at the drag, but the scabbard is intact at that point. The hilt is canvas wrapped with iron wire.” PROVENANCE: Ben Michel collection. CONDITION: Blade overall is gray/bright with scattered areas of black staining and pitting. Scabbard retains most of its original, red/brown paint, though there is a repair about 5″ above drag. Grip leather is about 90% intact, wire is complete. Protective washer is replaced. 4-31392 JS1 (4,500-6,500)

VIRGINIA MANUFACTORY CAVALRY SABER. This is a fine example of late-production Virginia Manufactory cavalry saber, shortened and re-scabbarded by Ames for the state of Virginia just prior to the Civil War. Ames’ conversion consisted of shortening the once massive blades to 34″ and adding a brass-mounted, iron scabbard. This example is much better than most examples encountered, as this example retains almost all of its orig grip wrap. Mr. Michel’s Notes State: “This cavalry saber is a 3rd Model Virginia Manufactory saber which has been slimmed and rescabbarded for Confederate usage. The new scabbard has brass ring mounts typical of this Confederate alteration.” PROVENANCE: Ben Michel collection. CONDITION: Blade is gray/bright with scattered nicks and resharpened cutting edge. Hilt exhibits a few minor dings and clearly shows forged manufacture with some laminated open seams. Grip retains about 80% leather wrap and orig brass wire, worn at high spots. Iron hilt and scabbard body exhibit good brown patina with pitting. 4-31394 JS5 (3,500-5,500)

CONFEDERATE CAVALRY SABER. This classic Confederate cavalry saber was probably made by Louis Haiman of Columbus, Georgia. Haiman features include lap seamed, lead-soldered scabbard with soldered throat and heavy, 1840-style hilts. Blade exhibits longitudinal faults. Another feature we have never seen on an enlisted cavalry saber before, but also often seen on Haiman officer swords, is a leather covering over scabbard body. Hilt is also more refined and finished on this example and may be an officer-carried “fighting sword.” Mr. Michel’s Notes State: “Confederate cavalry saber with finely cast, thick, brass guard. The grip is leather wrapped with plain iron wire. It is unmarked and is not identified as to the manufacturer. The scabbard is typically seamed but appears to be soldered rather than brazed. There are brass rings and the remnant of what apparently was leather wrapping on the scabbard itself. The entire sword is in “as found” condition, having remained untouched for a century and a half.” PROVENANCE: Ben Michel collection. CONDITION: Blade is brown/bright with areas of black staining and pitting. Protective washer is replaced. Grip retains almost all its orig leather and all orig iron wire. Grip is worn and scuffed on high spots. Hilt and brass mounts exhibit rich patina. Scabbard retains about 40% orig leather covering, though dry and split at seam. Scabbard retains orig soldered throat, which is missing on most examples by this maker. 4-31395 JS3 (3,500-5,500)

CONFEDERATE IMPORTED MODEL 1853 CAVALRY SABER. This is an example of the popular blockade run English cavalry saber with a 34-1/2″ blade, iron mounted scabbard, iron hilt, and compressed leather grips. This sword is devoid of markings, and Mr. Michel states that it was orig acquired from a family where it had been passed down through generations as the ancestors of a Confederate cavalryman. There is no reason to doubt that this was carried by a Confederate soldier, as this sword retains the look of other Confederate swords so preserved. Mr. Michel’s Notes State: “Pattern 53 Enfield cavalry saber. Iron hilt, 34¼” blade with iron scabbard. The sword is completely unmarked. Although the sword is not marked, it is typical of those imported to the Confederacy and was acquired from a family where it had been passed down through generations as the ancestor’s Confederate sword. While such oral “provenance” is notoriously and frequently inaccurate, in certain cases, where there can be no purpose to deceive and the story fits with the article, it is wrong to entirely dismiss what one is told.” PROVENANCE: Ben Michel collection. CONDITION: Blade is brown/bright with old nicks in cutting edge from possible battle use. Iron hilt and scabbard exhibit dark patina, old paint, and pitting. Leather grips are intact, but shrunken and cracked. 4-31320 JS4 (500-800)

CONFEDERATE STATES NAVAL CUTLASS. This is the most popular and the most classic example of Confederate naval cutlasses. This sword exhibits a 21″ blade with a central ridge line and cast brass hilt with feathered grip, which has a cast “CSN” and fluted anchor in the pommel. Hilt also has large, crudely cut Roman numerals “II” and “VI” cut inside basket. This sword originally was in the collection of Ralph Arnold. Mr. Michel’s Notes State: “Confederate States navy cutlass. This cutlass is probably the finest example of this weapon in existence. The full length, 21” blade shows only manufacturing flaws in the metal. The hilt is in flawless condition with “CSN” cast into the pommel cap. When found, the scabbard had disintegrated into fragments (probably thereby preserving the blade, but still attached was the original canvas and leather frog for the scabbard. Provenance: Ex. coll. Ralph Arnold.”The frog mentioned here is being sold as Lot #1191. CONDITION: This example is about as fine as can be expected. Blade exhibits orig polish and scattered, laminated flaws. 4-31396 JS8 (4,000-6,000)

CONFEDERATE SHORT ARTILLERY SWORD. 18-1/4″ dbl-edged blade. Cast hilt with concentric rings. These swords are thought to have been made in Macon, Georgia. Similar swords marked “E. J. Johnston” have very similar hilts. This particular unmarked example has good patina to hilt and blade. PROVENANCE: Ben Michel collection. CONDITION: Blade is brown with pitting, old sharpening, and grinding marks. Hilt exhibits rich patina. 4-31474 JS12 (1,500-2,000)

CONFEDERATE CARTRIDGE BOX, CAP BOX ON ORIGINAL ROLLER BUCKLE BELT. This complete outfit for a Confederate rifleman is remarkable, quite unique for its completeness and totally untouched “attic” condition. Mounted onto a roller buckle belt, this originated in North Carolina many years ago, and we doubt a better one has ever surfaced. Cartridge box and cap box have classic Confederate features, including lead finials, rough hewn, sewn leather bodies, Cap box and cartridge box are clearly of the same manufacturer, having been made of the same gauge of leather, with the same sewing skills and same finish to leather edges. Cap box is in remarkable condition, still retaining the orig lamb’s wool. Cap box has classic single loop, and the cartridge box has the classic sewn double-loops, with no provision for over-the-shoulder strap. Cartridge box is fitted with a single tin which still exhibits most of its orig finish. Cartridge box also has about a 1″ maker’s cartouche with large letters “A.F.” stamped in lower left hand quadrant of front flap. Belt also is in excellent condition, having a forged roller buckle sewn onto the tongue of the belt. This is a remarkable rig that we doubt could ever be duplicated or upgraded. Mr. Michel’s Notes State: “This complete outfit for a Confederate rifleman is remarkable, quite possibly unique for its completeness and its totally untouched condition. Mounted on the original belt with roller buckle are the matching cartridge box and cap box, both clearly of Confederate manufacture. The finial of each is made of lead and the dark rust brown leather is almost 3/8” thick. The cartridge box has only belt loops for a waist belt and no provision for an over-the-shoulder sling to be attached. The simply made belt with roller buckle is also as classic a Confederate infantryman’s belt as any could be.” PROVENANCE: Ben Michel CONDITION: All leather is very sound. Surfaces on all pieces have mottling, some flaking, and are scuffed at high areas. Tabs on both boxes are worn and a bit fragile, but sound and still attached. 4-31421 JS42 (10,000-15,000)

MORSE CARBINE CARTRIDGE BOXES AND BELT. This is a very rarely encountered rig. No more than a handful of orig Morse cartridge box belts & cartridge boxes survive. Consists of 2 cartridge boxes, about 11″ x 4″ each, each holding 12 tin tubes. Each tube would have held a Morse cartridge. The 2 boxes are suspended on a canvas belt, by pairs of brass belt loops. Belt is in very good condition overall, being complete with leather end and roller buckle. Leather tab at other end is complete. Cartridge boxes have tarred flaps. One box appears complete with all 12 compartments sealed with their tin tubes. This box contains both tabs. The second box retains all 12 tubes; however, the leather compartments in this box have much deterioration and 5 or 6 of the tin tubes are loose. This box has one complete tab, and one is broken off. Regardless, this is a spectacular belt and set of boxes. We have offered one set a few years ago, but the condition on this set is superior. Mr. Michel’s Notes State: “The Morse carbines were issued with a unique pair of cartridge boxes. Each box, made of leather, holds twelve tin tubes in twelve loop pockets. The two boxes are suspended on a web belt by pairs of brass loops. Rare, to say the least, this set is one found in a crate marked for “20 Morse’s carbines improved”.” PROVENANCE: Ben Michel collection. CONDITION: Belt is sound and complete, though canvas belt is soiled. Leather retaining roller buckle is sound and complete. Leather tongue is complete and sound with crazing and mottling and scuffing. Leather surfaces on belt retain most of their orig surfaces. Both boxes exhibit crazing and mottling of surfaces with scuffing and chipping, especially on back of the lesser conditioned box. Interior of the lesser conditioned box is flaking, and much of the leather covering of the tin tubes is very fragile. Coverings for two of the tin tubes is totally missing, though all tin tubes are intact and present. 4-31346 JS44 (5,000-10,000)

CONFEDERATE CARTRIDGE BOX WITH LINEN SLING. This is the classic Confederate Infantryman’s rig. Box is made of thick, russet leather with no belt loops. There is provision only for over-the-shoulder linen strap which has been cross-stitched to strengthen the doubled-over fabric. Cartridge box closes on a lead finial. Cartridge box on this sling has the left corner of the outermost flap of box upturned. Paul Johnson, in his book on Civil War cartridge boxes, notes that this is frequently observed in contemporary photographs. This was apparently done deliberately by soldiers for ease of access to the cartridges inside. A set of 3/4-inch initials, “JHC”, are scratched into top of flap on face of cartridge box, indicating the soldier who carried this box. Sling, though soiled and showing use, is quite sound and will support this box for display. Sling, however, is missing portions of both sewn, leather ends, one being almost totally gone, the second missing the end that attached to buckle on box. Cartridge box is missing both roller buckles, but leather tabs to secure them, though torn, are mostly intact. Box is missing its tin cartridge compartment. This brown leather box is quite sound and displays beautifully on its strap. Finding orig Confederate cartridge boxes on their orig linen slings is a difficult undertaking, and you will not find a much more presentable rig as this. Mr. Michel’s Notes State: “Russet brown leather Confederate cartridge box with linen sling. This is the classic Confederate infantryman’s rig. The box is thick rust leather with no waist belt loops on the reverse. There is provision only for the over-the-shoulder linen sling which has been cross-stitched to strengthen the doubled-over fabric. The box finial is of lead as frequently found to avoid the unnecessary use of brass where a substitute metal was available. Interestingly, the left corner of the outer flap of the box is upturned as noted in Paul D. Johnson’s book on Civil War cartridge boxes to be frequently observed in contemporary photographs. This was apparently done deliberately by the soldiers for ease of access to the cartridges inside.” PROVENANCE: Ben Michel collection. CONDITION: Strap is missing most of one leather tab and the other is broken. Linen is mostly complete, having several tears, reinforcing thread loose and torn in areas. An area about 1-1/2″ x 3/4″ is missing is center of strap, near where it was probably hung from a nail. There are rust stains in that area. Cartridge box is sound and dry. Cartridge box is complete with exception of missing tin and roller buckles. Box surface exhibits some crazing and cracking, but most of orig surface is present. 4-31420 JS43 (5,000-7,000)

“CS” EMBOSSED CONFEDERATE CAP BOX. Among the rarest and most desirable of Confederate cap boxes are the boxes embossed “CS”. Box is the classic Confederate cap box, with single belt loop, lead finial, and “CS” embossed in a 1-1/4″ x 1″ cartouche on face of box. These embossed boxes are quite rare and rarely offered. The “CS” embossing on this box is very clear and untouched. Box retains inner flap and lamb’s wool. Mr. Michel’s Notes State: “While unquestionably all Confederate leather goods are rare, most rare of these are the ones marked either with a maker’s name or, in this case, with the classic “CS” in an oval. Typical Confederate construction with a small rear loop for placement on the soldier’s belt and the classic lead finial, this cap box is also clearly embossed on the front flap with the letters “CS” in an oval.” PROVENANCE: Ben Michel collection. CONDITION: Box is sound and solid; however, front flap shows edge deterioration, missing a portion of front flap, as can be seen in photos. Tab is fragile and has an old, sewn repair. Belt loop is fragile with several large cracks and tears but is mostly complete. 4-31424 JS47 (5,000-8,000)

“GETTYSBURG BATTLEFIELD” CONFEDERATE CAP BOX. Classic Confederate brown leather cap box retains old tag stating it was picked up on the battlefield of Gettysburg. Tag reads, “This cartridge box was picked by father on the battlefield of Gettysburg a few days after the battle, Theodore K. Long”. This classic cap box retains its large single belt loop, long brass finial, and its orig vent prick. Mr. Michel in his notes states, “Except for its color, a rich brown, this cap box would appear to be US issue rather than Confederate made. The finial brass is rather than lead, but the construction, including the wide single belt loop, identifies it with its origin, south and not north of the Mason-Dixon line”. CONDITION: Box is solid and complete. Surfaces are good with some scuffing at high areas. Crazing is visible at folds. 4-31425 JS49 (2,000-3,000)

CONFEDERATE CAP BOX. This classic, single-strap, Confederate cap box, according to Mr. Michel’s notes, is a little larger than usual, and there are features of this cap box which cause it to resemble the English cap boxes furnished with imported Enfields. The finial has had the point visibly and deliberately cut off. Apparently this was done contemporaneously with its use, undoubtedly like the habit of turning up the flap on cartridge boxes for the ease and access. CONDITION: Surfaces of box are good and solid, with some crazing and mottling. Most orig surface is present. Box is a bit compressed with one ear coming loose from inner flap but still partially attached. Tab is complete and solid. Remnants of wool are still present. 4-31422 JS45 (800-1,200)

CONFEDERATE CAP BOX. A classic Confederate cap box made with single belt loop, lead finial, and no inner flap. Box still retains its orig vent prick. Box is in as fine condition as you will find. Surfaces are excellent, and sewing is tight and complete. Mr. Michel’s Notes State: “A classic Confederate cap box of thick leather, a single wide belt loop, and lead finial.” PROVENANCE: Ben Michel collection. CONDITION: Solid and complete. Smooth surfaces with minor cracking and crazing, especially at folds. 4-31426 JS48 (1,200-1,800)

CONFEDERATE CAP BOX. This is quite the unusual Confederate cap box. It is very simply made with the front flap acting as a tab over a lead finial placed on the front bottom of this box. Box has no inner flap and is made of very thin leather. Due to the fact that there is no inner flap and more stress at the back fold, the stitching is reinforced with two brass pins. Box overall is in fine condition for a piece of Confederate leather, being complete and sound with good surfaces throughout. Mr. Michel, in his notes, states, “This box follows the pattern of pre-War cap boxes which had the finial placed on the front of the interior pouch as opposed to the more usual bottom placement. The finial here is lead. The leather is a russet brown color, and the small belt loop is stitched integral with the edge stitching of the box—all features common to confederate manufactured cap box”. CONDITION: Leather is complete, sound, and supple. Orig surfaces have scattered bends, folds, and mottling. 4-31423 JS46 (1,200-1,800)

CONFEDERATE TREDEGAR BAYONET SCABBARD AND FROG. This very rare Confederate scabbard for a Tredegar socket bayonet is all hand-stitched with a lead finial tied to bottom of scabbard. These lead scabbard tips are very commonly found on battlefields, especially in the Army of Northern Virginia sites. We would imagine there are no more than a handful of these scabbards known. We can think of only 6 or 7 in collections and institutions. These scabbards are among the rarest of Confederate-associated accouterments. Mr. Michel’s Notes State: “This very rare Confederate scabbard for a socket bayonet is all hand stitched with a lead finial sewn to the tip as an endpiece. While the leather body is flaking in places and the belt loop is fragile, it is in overall sound condition and, considering the great rarity of this particular accoutrement, it is in very good condition.” PROVENANCE: Ben Michel collection. CONDITION: Scabbard body is sound with much of its orig black surface remaining. Frog is fragile but intact with several tears. 4-31427 JS40 (1,000-2,000)

CONFEDERATE TREDEGAR SOCKET BAYONET SCABBARD AND FROG. This is another example of the very rare Confederate angular bayonet scabbard. It is all hand-stitched and in very good condition overall, with exception of its broken tip, which at one time had a lead finial. This scabbard retains much of its orig black surface with only minor crazing and loss of finish. Frog is very good, though dry. Mr. Michel’s Notes State: “Perhaps the rarest Confederate leather accoutrement is the scabbard for the socket bayonet. Having no civilian use, thse few that survive only do so because some veteran saw it as an appropriate souvenir if otherwise lacking the appeal of a cartridge or cap box, much less a Bowie knife or canteen. This example is of heavy leather and shows no sign of ever having a trip unless it was a simple lead finial sewn into the leather. Most likely the body of the scabbard was simply sewn down to the end.” PROVENANCE: Ben Michel collection. CONDITION: Overall, surfaces are dry. Black surface is flaking but mostly intact. Tip of scabbard is broken off. 4-31428 JS41 (1,000-2,000)

FROG FOR CONFEDERATE NAVAL CUTLASS. Rarely found is the orig canvas and leather frog that normally accompanied the classic Confederate naval cutlass that exhibited CSN and fluted anchor pommel. There are a good many orig scabbards out there but few frogs. If you have a naval cutlass with its orig scabbard, here’s a chance to buy the rarest accessory to go with it. PROVENANCE: Ben Michel collection. CONDITION: Canvas is sound with several tears. A 1″ cut or tear is present in the top. Leather is complete and sound, though sewing on 1/2 of one edge is missing and only about 10 or 20% of the orig black surface is present. The rest is chipped or worn off. 4-31480 JS50 (300-500)

CONFEDERATE SPURS. Nice pair of large, Confederate variant spurs with iron rowels. PROVENANCE: Ben Michel collection. CONDITION: Spurs exhibit similar patinas. One rowel heavily rusted, only about 50% intact. 4-31385 JS58 (300-500)

CS ROPE BORDER BUCKLE ON BELT This is a fine example of the classic “CS Rope Border” buckle on its orig brown, leather belt. This buckle is similar to Fig. 270 in Kerksis. Excavated specimens of this buckle are found at Shiloh, Port Hudson, Vicksburg, and all through the Atlanta campaign. This was a popular buckle in the Western armies, and non-dug specimens are scarce, especially as nice as this one. Mr. Michel’s Notes State: “”Rope border” Confederate “CS” belt plate of stamped brass with twisted rope design encircling its inner border.” PROVENANCE: Ben Michel collection. CONDITION: Buckle is well-struck, having only minor nicks and scratches. Hooks are very good and complete. Brown leather belt is dry. 4-31405 JS33 (6,000-8,000)

ENLISTED CONFEDERATE CS BUCKLE & BELT This buckle is the classic, lead-filled, CS egg, similar to Kerksis’ Fig. 273. This particular buckle is in very good condition with full lead and hooks on reverse. Soldier scratched his initials “SRS” into back of plate, along with other, indiscernible writing. This is a scarce variety of buckle associated with the Army of Northern Virginia. The belt this buckle is on originally had a buckle with “puppy paw” hooks, but this buckle has been with this belt a long time and displays nicely with it. It would be difficult to find a better specimen of this buckle. Mr. Michel’s Notes State: “Stamped copper with wire hooks held by lead or solder filling. Oval in shape with “CS”.” PROVENANCE: Ben Michel collection.` CONDITION: Buckle exhibits several small dents, scratches, and small bends at top and right side. 4-31408 JS31 (6,000-8,000)

CONFEDERATE OVAL ENLISTED BELT & BUCKLE. This is a classic example of the CS egg which is most commonly excavated in very early sites around Mobile and Pensacola campsites and early Western Theatre battlefields. This buckle, though very commonly excavated, is quite scarce non-dug, especially on its original belt. This buckle is similar to Fig. 272 in Kerksis’ book Plates and Buckles of the American Military. This buckle was made by simple soldering a set of iron hooks to the stamped brass face. These buckles are often poorly stamped. This example has a very good, clear “CS”. This belt and buckle are guaranteed authentic and original in every regard. This is a fine example of a difficult plate to find non-excavated. It would be difficult to upgrade this plate on its orig belt. Mr. Michel’s Notes State: “Stamped brass with wire hooks held by light solder or lead filling. Oval in shape with “CS”.” PROVENANCE: Ben Michel collection. CONDITION: Buckle exhibits numerous small scratches in face. Belt is flaking and has areas of insect damage, but is still sound and solid. 4-31404 JS32 (6,000-8,000)

CSA RECTANGULAR BELT PLATE ON BELT. This is as fine an example as you will find of the classic “Atlanta pattern” C.S.A. belt plate. Georgia, or Atlanta pattern CSAs are generally thicker than their eastern counterparts and have smaller periods. This example has both these features plus has highly-detailed “C.S.A.” lettering. It would be difficult to obtain a better CSA rectangular belt plate on its orig brown belt. Mr. Michel’s Notes State: “”Atlanta Arsenal”-type Confederate “CSA” belt plate.” PROVENANCE: Ben Michel collection. CONDITION: Buckle is slightly bent but exhibits fine mustard patina. Brown belt is dry but sound. 4-31406 JS34 (6,000-8,000)

CS BRECKENRIDGE BELT PLATE ON BROWN BELT. This buckle is similar to Kerksis’ Fig. 277 or 278. This is a very scarce, non-excavated plate. Hooks on this buckle appear re-soldered, and one hook appears replaced. Belt was orig for a “puppy paw” style buckle. Regardless of the reattached hooks and replacement belt, this is a very scarce buckle in non-excavated condition. Mr. Michel’s Notes State: “”Regulation CS” belt plate of stamped brass and soldered flat belt hooks.” CONDITION: Surface of plate exhibits numerous small dents and scratches and old cleaning. Belt is crazed, but sound and solid. 4-31407 JS35 (5,000-7,000)

CLIP CORNER CS BUCKLE ON BELT. This is the classic CS clip corner buckle commonly found in Confederate cavalry sites in the Western Theater. Sid Kerksis, in his reference book, states in his opinion, “It is one of the most attractive of the belt buckles fabricated by the Confederate central government.” He states, “There is reason to believe they were possibly manufactured in Columbus, Georgia. They are well-made and finished and have a black enamel background,” which is present on this example. This buckle shows the typical “spinning marks” always seen on this particular type of CS clip corner buckle. It would be difficult to find a nicer example of this popular Confederate buckle. The accompanying belt does not appear orig to this buckle, but this buckle displays very nicely on it. Mr. Michel’s Notes State: “”Line in Hooks” case brass belt plate of heavy casting, integral belt hooks.” PROVENANCE: Ben Michel collection. CONDITION: Buckle is very good overall, exhibiting fine patina and strong traces of orig background enamel. Belt has been cut, broken, and repaired. 4-31409 JS36 (3,500-4,500)

CAST BRASS OVAL BELT PLATE ON BELT. This plain, cast brass, oval plate was probably made prior to the American Civil War. These plates are often seen with various engraved motifs. The Confederates, utilizing whatever they could, used plates and buckles like this, based on excavated finds of similar buckles. This buckle appears to be on its orig belt, missing the sewn belt keeper. Mr. Michel’s Notes State: “Oval cast brass with flat, oval belt pins and belt hook on belt.” PROVENANCE: Ben Michel collection. CONDITION: Buckle is very good, with scattered stains and scratches overall. Belt is solid, has minor crazing, and some insect damage. 4-31412 JS37 (500-1,000)

RECTANGULAR CS SABER BELT PLATE. This buckle, 1-3/4″ high x 2-1/4″ long, is most unusual. We believe this buckle to be Veteran’s era; however, since this buckle was cataloged by the Chicago Historical Society in 1917, it is possibly wartime. We have not seen another plate exactly like this. Buckle has a keeper with it, though it does not fit perfectly. Buckle appears sand cast with a cast “W” in back along with an old catalog number in black ink. Mr. Michel, in his notes, states, “Confederate rectangular sword belt plate with cast CS inside edge frame. This plate comes from the Gunther collection disbursed by the Chicago Historical Society. The back of the plate has ink accession number 1917.32. This type plate is pictured by Sydney C. Kerksis in his book Plates and Buckles of the American Military, 1795-1874 on pages 303-304. Described by Kerksis as ‘quite rare,’ both plates shown are from the Virginia Historical Society collection.” Buckle shows wear with numerous small scratches to face. CONDITION: As described above in description. 4-31419 JS63 (400-800)

CONFEDERATE GEORGIA FRAME BUCKLE. This frame buckle, which is 2-3/4″ x 2-1/2″, is one of the numerous varieties and styles of frame buckles utilized by both Eastern and Western Confederate armies. These buckles, though common excavated, are quite scarce unexcavated, as this one is. This buckle displays quite nicely on a reproduction belt made specifically for it. Mr. Michel’s Notes State: “On reproduction belt.” PROVENANCE: Ben Michel collection. CONDITION: Buckle has been cleaned overall. Still retains patina in protected areas, especially inside the numerous dings, dents, and scratches. 4-31410 JS38 (750-1,500)

CONFEDERATE “FORKED TONGUE” BUCKLE. This buckle measures 3-3/4″ x just over 2-1/2″. This is one of the numerous varieties of this particular plate used by both Eastern and Western Confederate armies. These buckles are commonly excavated on battlefields and campsites in all theaters of war, often with missing or broken tongues. This particular specimen is excavated also and highly cleaned and put on a reproduction belt to show how it was worn. Mr. Michel’s Notes State: “On reproduction belt.” PROVENANCE: Ben Michel collection. CONDITION: Buckle exhibits several bends to body and to tongue. Reproduction belt is wearable and sound. 4-31411 JS39 (500-1,000)

CONFEDERATE CEDAR WOOD CANTEEN RECOVERED AT THE BATTLEFIELD OF CEDAR MOUNTAIN, VIRGINIA. This canteen was taken from the body of a NC soldier who died on the battlefield. His name, “W. D. Redfern” is nicely scratched into surface of canteen. Attached tag tells the story, “This canteen was taken from the body of a captain of a Confederate N. C. Regiment who was killed at the Battle of Cedar Mountain, presented to W. E. Rogers by the Sheriff of Culpepper Co.”. Canteen retains a thin linen sling. Mr. Michel tells the story of this canteen as follows: “Typical Confederate wood canteen with linen sling. When found, this canteen had an old paper pasted on the side reading, ‘This canteen was taken from the body of a Captain of a Confederate N. C. Regiment who was killed at the battle of Cedar Mountain. Presented to W. E. Rogers by the Sheriff of Culpepper Co.’ At the edge of the paper the initials W. D. R. were visible carved on the canteen. When the paper was removed intact the full name Redfern appeared formerly covered by the paper. W. D. Redfern was 1st Lt of Co A of the 23rd Reg of NC Inf when he died on May 10, 1862. Interestingly his rank was probably mistaken by the person who took the canteen from his body because his two bar collar insignia, designating him as a 1st Lt in Confederate service could have been taken for the two bar designation of a caption in the U.S. service”. This is a rare opportunity to buy a battlefield recovered relic with such wonderful provenance. CONDITION: Canteen appears to be an “attic” find. Surfaces are well patinated, including iron banding and wood. Wood is light where tag was removed. A mouse made a home in this canteen, as can be seen by the gnawing marks around spout. This is not the first canteen we have seen that a mouse made as his home. Sling has two areas of newer sewing. 4-31418 JS57 (5,000-8,000)

DECORATED CONFEDERATE WOOD CANTEEN. This is a classic 7″ cedar wood canteen, commonly used by both Army of TN and Army of N.VA. Canteen has a wonderful, commemorative painting, described by Mr. Michel as follows: “Confederate wood canteen painted with crossed Confederate flags. On the right is the first national pattern with a field of red, white, and red stripes and a canton with the St. Andrew’s cross, and on the left is the second national pattern with a white field and (albeit incorrectly) also a St. Andrew’s cross. Both flags are surmounted with the letters ‘C.S.A.'”. CONDITION: Canteen is no longer perfectly round. It may never have been. One of the 1-1/2″ wood slats is missing and is replaced. Bands are loose. Numerous scratches and nicks. Painted decoration is partially obscured by scuffs and wear. 4-31416 JS55 (2,000-4,000)

CONFEDERATE CEDAR WOOD CANTEEN. This is a variant of the classic Confederate cedar wood canteen. This variant is banded with brass bands instead of iron and has a wonderful, orig, leather strap which holds a forged snap hook that would attach this to a knapsack or saddle. Canteen also is nicely identified to a soldier from Perry County, AL. Mr. Michel notes explain this AL soldier’s history as follows: “Confederate wood canteen with leather belt and hook closure. Side of canteen is engraved, ‘S. Nichols Perry Co. Ala.’ Nichols enlisted on Oct 30, 1863, at Selma, AL. He was a Sgt in Cpt Sengstak’s company, 2nd Battalion, AL Lt Art. On Feb. 20, 1865, he was in the Way Hospital at Meridian, MS, with a wound and was furloughed”. CONDITION: Canteen appears to be an “attic” find with nice patina to brass and wood surfaces. Large age crack in both plates of the canteen. Obverse face of canteen also has a 2″ chip at base. Leather strap is complete and solid. Leather strap is constructed with 2 layers of leather. Outside layer is solid and complete. Inner layer has numerous cracks and breaks, especially at folds. 4-31417 JS56 (4,000-6,000)

CONFEDERATE TIN CANTEEN. This is a very rare, decorated, souvenir Confederate tin canteen in wonderful condition. Reverse of canteen clearly shows a large bayonet hole. Was this bayonet hole made in battle, or did some Union soldier just render this canteen unusable for the next Confederate to find it on the battlefield? Mr. Michel, in his notes, describes this canteen quite well as follows: “Confederate tin canteen with old silver paint and black stylistic paint inscription on the side, clearly of the period, ‘A relic of the Civil War 1860 worn by a Rebel Private’ with other decorative lining. This is typical of the type of ‘captured’ or battlefield souvenir items displayed at the sanitary fairs during the war and at small local museums in the postwar period”. CONDITION: Paint on canteen is very good with some chipping and paint reduction on sides, scattered rust and pitting. 4-31413 JS52 (4,000-6,000)

CONFEDERATE TIN CANTEEN. This 6-1/4″ Confederate tin canteen is a scarce variant, rarely seen, with raised edges on both surfaces. Canteen exhibits its orig linen sling attached with roller buckle. We have seen no more than 2 or 3 of this pattern canteen, and this particular example would be very difficult if not impossible to upgrade, especially on this wonderful, Confederate-made, linen sling with roller buckle. Mr. Michel’s Notes State: “Confederate tin canteen with original canvas sling with iron roller buckle.” PROVENANCE: Ben Michel collection. CONDITION: Canteen is solid with several dents, scattered rust. Sling is solid, missing several inches of its end, and is heavily soiled. 4-31415 JS54 (3,000-5,000)

CONFEDERATE TIN CANTEEN WITH ORIGINAL COVER AND SLING. This 6-1/2″ x 1-3/4″ canteen is one of many variants of tin canteens used during the Civil War. This canteen is as complete as you will find. Mr. Michel, in his notes, sums it up as follows: “Confederate tin canteen with ‘butternut’ color cloth cover and linen sling. If Confederate canteens are not readily found today, they are almost never found with the original cloth cover still intact, and then still more rarely with the original sling”. CONDITION: Canteen has several dents. Exposed surfaces are smooth with some rust and pitting. Butternut cover is complete with some minor moth damage and heavily soiled. Sling is fragile and has several tears but is sound and will support canteen with no fear of breaking. 4-31414 JS53 (3,000-5,000)

CONFEDERATE FLAP HOLSTER. This holster is possibly a Confederate copy of a U.S. military holster for a Navy-sized revolver such as a Griswold or Leech & Rigdon. Holster is simply made by sewing one edge to the muzzle. Muzzle plug is also sewn into place, which is now partially detached. Flap is closed by an odd-shaped, brass finial. Belt loop is quite small, being just over 5/8″ wide, attached with 2 brass rivets. Regardless of who made this holster, it would make a nice display with any Confederate revolver of its size. Mr. Michel’s Notes State: “Thin, leather, hand-sewn holster with brass finial to hold top flap. Single narrow belt loop held by a single rivet.” PROVENANCE: Ben Michel collection. CONDITION: Leather is supple. Stitching is still complete, except at muzzle where plug has broken loose but is still partially attached. Leather surfaces are well worn and flaking, especially at folds. Black surfaces are flaking, mottled, and crazed. 4-31365 JS91 (1,000-2,000)

CONFEDERATE-USED HOLSTER Standard military-style Navy-sized holster. Belt loop is attached with 2 copper rivets. Finial is a furniture tack, sometimes seen on Confederate cartridge boxes and accouterments. Mr. Michel’s notes state the following: “Dark brown leather holster with flap held by copper finial. Single wide belt loop secured with 2 copper rivets. When found, the holster held a Griswold & Gunnison revolver, since separated. The holster has secured to the back an old label reading o’Griswold & Grier Confederate’ as these revolvers were once known.” Finding Confederate holsters that are truly associated with Confederate handguns is difficult. This is a nice, usable, displayable holster that could be used with any Griswold or Iron Frame Navy revolver. CONDITION: Solid and supple. Several small cracks and tears at folds. Belt loop is solid. Plug at muzzle is broken, and only about 50% present. Surfaces are crazed and mottled. Black surface is almost completely intact. Brass finial and rivets are nicely patinated. 4-31364 JS89 (1,000-2,000)

CIVIL WAR ERA OPEN TOP HOLSTER. This is a typical “Slim Jim” holster for a Navy-sized revolver with opened muzzle end. Well-made holster sewn along one edge. Single belt loop is retained by 3 brass rivets. Mr. Michel’s Notes State: “Russet brown leather holster, hand stitched with a wide single belt loop secured by a single rivet.” PROVENANCE: Ben Michel collection. CONDITION: Thread is broken at about 1/2 of sewn edge length. Leather surfaces are sound, but black coating is cracked and crazed, and much has worn off or chipped away. 4-31366 JS90 (300-500)

OPEN TOP HOLSTER. This classic “Slim Jim” holster would hold an army or navy pistol, simply sewn along one edge with no provision at muzzle. Belt loop is attached with 2 iron rivets. Mr. Michel’s Notes State: “Heavy leather holster for a Navy-type revolver, hand stitched with a single belt loop, also of thick leather, secured by a single rivet.” PROVENANCE: Ben Michel collection. CONDITION: Supple with areas of mildew staining, especially inside. 4-31367 JS92 (100-200)

PAIR OF SADDLE HOLSTERS FOR LARGE REVOLVERS. Colt Dragoons or even Dance Army revolvers would fit nicely in these patent leather-covered pommel holsters with large, brass tips. Holsters are complete with covers and tabs that attach to brass finials. PROVENANCE: Ben Michel collection. CONDITION: These holsters have seen some use. Several areas of covers are torn and worn through; however, they are still solid and will display nicely on saddle. Much of orig surface is still present. Bodies of holsters exhibit several cracks, but holsters are intact. 4-31384 JS93 (500-800)

PAIR OF SADDLE HOLSTERS. These holsters appear to date from the early-to-mid 19th century and would contain any American martial pistols made in the 1820s, 30s, and 40s. Holsters have large, formed single flaps with tabs that attach to large brass finials above large, protective brass caps with floral decorations on base. PROVENANCE: Ben Michel collection. CONDITION: Brass base caps originally attached by brass pins or wire. Pins or wire are missing. Holsters are complete, as are flaps. Surfaces retain most of their orig black finish, with some crazing and mottling, especially at folds and on the piece of leather that connects the holsters. Rich red/brown patina to protective caps. 4-31383 JS94 (1,000-2,000)

CONFEDERATE MAPLE DRUM. This drum, 12″ high x 14″ in diameter, is typical of snare drums used by both sides during the Civil War. Drum has repainted red hoops, maple body with numerous defects, not typical of a drum for civilian or Northern military use. This drum has tag opposite vent from the restorer which reads: “Repaired and restored / by / W. H. Reamer / January 1988 / Broomall, PA”. Drum is accompanied by pair of period drumsticks. Mr. Michel, in his notes, states, “Drum was found in southern New Jersey and it came from an old GAR post as a ‘rebel drum’. At one time there was a tag to that effect which has since been lost”. CONDITION: 4-31461 JS62 (1,000-2,000)

COOK & BROTHER TWO-DOLLAR BILL. On yellow paper, a 6-1/2″ x 2-3/4″ two-dollar bill issued by Cook & Brother, New Orleans. Note is serial numbered, dated March 15, 1862, and signed “Cook & Brother”. Vignettes include 2 crossed rifles, sailing ship, plow, etc. Note has green overprinted “TWO”. Mr. Michel’s Notes State: “Cook & Brother two-dollar note payable at New Orleans, March 15, 1862.” PROVENANCE: Ben Michel collection. CONDITION: 4-31297 JS51 (300-500)

PAIR OF ASHTRAYS MADE FROM 12-POUND CANNONBALLS. 2 ceramic bases have approx. 1/2 to 2/3 of exploded 12-pound Boreman shells securely attached. Area where the Boreman fuse went is clearly visible. Both shell fragments were excavated at unknown battle site and are deeply pitted and rusted as typical of battlefield recovered shell fragments. PROVENANCE: Ben Michel CONDITION: 4-31477 JS64 (100-200)

GREAT SEAL OF THE CONFEDERACY. Highly detailed 3-1/2″ impression of the Great Seal of the Confederacy, possibly an electrotype made directly on the seal, then lead filled. Seal is presented in its orig box. Box is imprinted “Manufactured and for sale by R. M. Cheshire, 716 8th Street, NE, Washington D.C”. Mr. Michel’s Notes State: “The seal, which is a lead-filled bronze impression, is in its original green paper box with velvet lining. The book has a picture on it of the seal and the notation that it was “Manufactured and for sale by R. M. Cheshire, 716 Eighth Street Northwest, Washington D.C.”” PROVENANCE: Ben Michel collection. CONDITION: Seal exhibits some orig luster, some minor scuffing, and pleasant patina overall. Orig cardboard box is separated with tears and missing some of its green paper covering. 4-31458 JS67 (500-800)

STONEWALL JACKSON MEDAL. White metal medallion is approx. 2″ and shows the bust of Stonewall Jackson on one side, and reverse has patriotic motifs listing battles he was involved in. These medals were made in France during the Civil War and were supposed to be given to members of the Stonewall Jackson Brigade, though distribution did not occur. These medals were sold after the Civil War, usually encased in a glass-shielded bezel. For more information on this medal, the Token and Medal Society newsletter published an article on these several years ago. Mr. Michel’s Notes State: “Bronze medal with portrait head of Stonewall Jackson on one side and a listing of his battles on the reverse.” PROVENANCE: Ben Michel collection. CONDITION: Still retains some orig luster, numerous small nicks and scratches on high areas. 4-31457 JS65 (200-400)

CONFEDERATE SOUTHERN CROSS OF HONOR. The Southern Cross of Honor as pictured here was made by Charles Crankshaw of Atlanta in the late 19th century. The United Daughters of the Confederacy gave these medals to any Confederate soldier who was honorably discharged or surrendered with his army or died during the Civil War. These medals were not issued named, and it was up to the soldier to have a jeweler inscribe or scratch his name himself into the name bar. “R. W. Jenkins” inscribed his name quite nicely. R. W. Jenkins appears on the rolls of the 6th and 8th South Carolina Infantry as Sgt and later Lt. Mr. Michel’s Notes State: “Confederate veteran’s medal presented to veterans by the United Daughters of the Confederacy. The nameplate is scratched with the name “R. W. Jenkins”. At one time these medals were so precious to the veterans and their families they were virtually unobtainable.” PROVENANCE: Ben Michel collection. CONDITION: Medal is in “as found” condition with pleasant patina on all surfaces. 4-31456 JS66 (500-1,000)

WOODEN BOX POSSIBLY FOR CONFEDERATE AMMUNITION. 14-1/2″ x 9″ x 8-1/2″ wooden, hinged box made in the style of arsenal ammunition boxes. Box is hinged and well made of nailed construction. Box is totally devoid of any markings. If this box was used for ammunition, it would have at one time been painted with the type of munitions it held. An integral lock is present on front of box and a keyhole is present on front face of wood. Key is no longer present. Several repairs have been made to this box so it could continue to be used for some utilitarian purpose. PROVENANCE: Ben Michel collection. CONDITION: 4-31438 JS61 (200-400)

CONFEDERATE VETERAN’S CANE. 35″ long cane, with top 15″ decorated with tacks, hearts, and moons cut out of brass, with the most interesting device being the “CS” medallion from a 2-pc “CS” sword belt plate surrounded by 2 letter “I’s”, possibly representing “Infantry”. There is no date or ID on this cane, but it appears typical of similar pieces of folk art from the late 19th century. Mr. Michel’s Notes State: “Walking stick wonderfully decorated with tacks and twine wrapping and, most notably, what appears to have been the center oval brass “CS” of a two-piece plate with a silver letter “I” inlet on each side.” PROVENANCE: Ben Michel collection. CONDITION: Cane has seen some use but is solid and sturdy. String wrap is soiled but complete. Several tacks and inlays are missing. 4-31459 JS60 (500-800)

LARGE 19TH CENTURY WATERCOLOR OF A CONFEDERATE SOLDIER. This approx. 22” x 16” watercolor on paper appears 19th century and possibly Civil War. Bearded enlisted man in uniform is shown pictured in front of fort with tents in background. Frame, backing, and glass are replaced, though frame appears contemporary to watercolor. SIZE: 22″ x 16″ CONDITION: Very good overall. 4-31479 JS237 (200-400)

LARGE FRAMED ENGRAVING OF ROBERT E. LEE FROM THE HOME OF A UNION GENERAL. This approx. 15” x 11” image of Robert E. Lee, according to notes on back of frame, was from the home of Gen. John Parkhurst, once Colonel of the 9th Michigan, later Brig. General. Even Union officers revered the great Robert E. Lee. Mr. Michel’s Notes State: “From home of John C. Parkhurst, Col, 9th Michigan & Brig. General, Army of the Cumberland.” SIZE: 15″ x 11″ CONDITION: Overall very good, with a couple light creases seen in paper of image. 4-31478 JS236 (200-400)

ORIGINAL OIL PAINTING BY DICK RICHARDSON OF TWO CONFEDERATE CAVALRYMEN ELUDING THE ENEMY IN THE SNOW. This well executed oil on board shows two cavalrymen being chased by the Yankees. One Confederate cavalryman is returning fire with his revolver. This undated painting is signed “Dick Richardson”. CONDITION: Very good overall. 4-31471 JS235 (300-500)

ORIGINAL OIL PAINTING OF CONFEDERATE ARTILLERY TEAM AT FULL GALLOP BY DICK RICHARDSON. This undated oil on board painting, signed “Dick Richardson”, is approx. 15” x 11” and shows Confederate artillerymen on their way to a fight. SIZE: 15″ x 11″ CONDITION: Very good overall. 4-31470 JS234 (300-500)

WATERCOLOR OF CONFEDERATE CAVALRYMAN WITH TARPLEY CARBINE. This approx. 14” x 10” watercolor signed “Sowers, 81” shows a Virginia cavalryman with a Carolina-made cavalry saber and a North Carolina-made Tarpley carbine. This horseman is wearing regulation cavalry boots, a sword belt with Virginia buckle, shell jacket and slouch hat. SIZE: 14″ x 10″ CONDITION: Image overall is very good with light fading. 4-31468 JS233 (300-500)

FRAMED NEEDLEPOINT OF THREE CONFEDERATE FLAGS. This well executed needlepoint of three Confederate variant flags is thought to be close to 100 years old and is beautifully framed in gilt inset walnut frame. Mr. Michel’s Notes State: “Beautifully executed needlepoint of three Confederate flags (two nationals and the battle flag) in handsome, antique, walnut frame with gilt insert. Work appears to be late 19th century or early 20th century.” SIZE: 14″ x 17″ CONDITION: Overall very good. 4-31460 JS273 (200-400)

GREAT SEAL OF THE CONFEDERACY. This 24” square reproduction of the Great Seal of the Confederacy was published by the Museum of the Confederacy in 1987. SIZE: 24″ x 24″ CONDITION: Very good overall. 4-31467 JS242 (200-400)

LIMITED EDITION PRINT OF “EMBLEMS OF VALOR” BY DON TROIANI. This unframed print is signed and numbered. Image size is approx. 24” x 20”. Accompanied by a document of authenticity from the publisher. SIZE: 24″ x 20″ CONDITION: Very good overall with a couple dents at corners. 4-31466 JS241 (200-400)

LIMITED EDITION PRINT OF “CONFEDERATE STANDARD BEARER” BY DON TROIANI. Framed and matted. Image size is approx. 16” x 20”. This print is one of Troiani’s first, most popular, and difficult to obtain editions. Signed, numbered and dated 1982. SIZE: 16″ x 20″ CONDITION: Very good overall, with light fading. 4-31464 JS240 (300-500)

LIMITED EDITION PRINT OF “THE GRAY WALL” BY DON TROIANI. This framed print, executed in 1985, is No. 504 of 950. Image size of this print is approx. 22” x 21”. SIZE: 22″ x 21″ CONDITION: Very good overall, with light fading. 4-31465(800-1,000)

LIMITED EDITION PRINT OF “FORWARD COLORS” BY DON TROIANI. This signed and numbered print, framed and matted, is from the orig painting dated 1983. Image size is approx. 24” x 18”. SIZE: 24″ x 18″ CONDITION: Very good overall with light fading. 4-31463 JS239 (200-400)

THE MOST IMPORTANT AMERICAN SWORD EVER TO BE OFFERED AT PUBLIC AUCTION. This represents a once in a lifetime opportunity to purchase what is considered to be, a national treasure. This solid gold, extremely high grade, presentation sword commissioned by the United States Congress, made by America’s premier blade smiths; The Ames Manufacturing Company of Chicopee, Massachusetts, and inscribed and presented to General David Emanuel Twiggs of Mexican War fame is the most important American sword in private hands and the only Mexican War Congressionally commissioned and presented sword to ever be sold at public auction. The Ames Manufacturing Company was commissioned by the United States Congress to design and fabricate this presentation sword for the phenomenal sum of $1,500 in 1848. At the time $1,500 was, without doubt, the most expensive American sword ever made by Ames and perhaps any other manufacturer of swords in the United States, or even the world. When James Ames was asked about the phenomenal cost of this sword he believed himself “fairly paid, but nothing more . . . the sword’s to be fully worth that amount.” (John Hamilton, The Ames Sword Company: 1829-1935, p. 115.) Historically, five other gold presentation swords were commissioned and presented to Mexican War heroes by Congress. One is documented to have burned in fire; three are institutionalized (one being in the White House). Only the sword to Major General William O. Butler is still family owned and was “discovered” on the Antiques Roadshow (t) in 2003. All six of these magnificent gold Congressional presentation swords were made by Ames by the same act of Congress in the same year (1848). All are distinct in design, craftsmanship and artistry. The Twiggs sword, presented here, has a spectacular history and provenance both before and during the American Civil War that is unique among all of the other Congressionally commissioned swords. This magnificent gold presentation sword is mounted with gemstones, including two large white sapphires, a topaz, and a rose-colored diamond. This sword is mounted and hilted in solid, 18-karat gold. This sword exhibits some of the finest casting art and engraving ever accomplished by any American sword manufacturer. The N.P. Ames Co. opened for business in 1791 at their factory at Chelmsford, Mass. In 1832 Nathan P. Ames signed his first contract with the U.S. Govt. for Foot Artillery swords. Ames also was the home of one of the largest brass, bronze and iron foundries in the country. They made cannon and rifled guns during the Civil War and many famous statues including the Minuteman Statue in Lexington, Mass. and the bronze doors for the U.S. Capitol. They also pioneered in plating for fine presentation swords. Noted and acclaimed throughout the world for their staff of expert bladesmiths, casters, artists, engravers and jewelers, the Ames firm made some of the finest and most beautiful American swords in history. This sword was presented to General David Emanuel Twiggs by President James K. Polk for extraordinary gallantry and service during the Mexican War. Born in Richmond County, Georgia, he was the oldest officer of the Federal Army to take up arms for the Confederacy. His father was General John Twiggs, a distinguished Revolutionary War officer referred to as the “Savior of Georgia”. Commissioned a Captain, 8th Infantry, on March 12, 1812, Twiggs fought valiantly in the War of 1812. He was promoted to Major, 28th Infantry, in 1814. Twiggs served with Generals Andrew Jackson and Edmund Gaines against the Indians in Florida during the Seminole War. He distinguished himself in the Black Hawk War and in the controversy between the United States and South Carolina in 1832. President Jackson, with whom he was a favorite, ordered him to command the U. S. Arsenal at Augusta, GA. He was commissioned Colonel, 2nd Dragoons, June 8, 1836, which, under his leadership and training, became one of the most renown cavalry regiments in the U.S. Army. Twiggs, as Colonel, 2nd Dragoons, joined General Zachary Taylor’s army at the outbreak of the Mexican War. In the movement upon the Rio Grande, Col. Twiggs led the advance and captured Point Isabel. His gallantry at the Battle of Palo Alto and Resaca-de-la-Palma resulted in a brevet promotion to Brigadier-General. At the Battle of Monterey he was in command of a division and given chief command of that place until ordered to join General Winfield Scott at Vera Cruz. At the Battle of Cerro Gordo he led the main attack, and served conspicuously at the Battles of Contreras and Churubusco. He led an assault at the Belen Gate and participated in the Assault and Capture of the City of Mexico. His actions in Mexico recognized he was honored with a brevet commission of Major- General for gallant and meritorious conduct at the Battle of Monterey and presented with this sword and a resolution by the United States Congress. Following the Mexican War Twiggs was given command of the Department of the West, with headquarters at St. Louis, MO, until 1857 when he took charge of the Department of Texas, headquartered at San Antonio. In late 1860 Twiggs was one of only four general officers of the line on the Army roster, the others being Winfield Scott, John E. Wool and William S. Harney. He was second in seniority to Scott and would have been in line to assume duties as General-in-Chief had Scott retired. Yet, Twiggs’ Southern sympathies caused him to surrender the military forces and stores under his command in Texas to Colonel Ben McCulloch, representing the State of Texas, an act for which Twiggs was dismissed from the Army on March 1, 1861. On May 22, 1861 Twiggs was appointed a Major-General in the Confederate Provisional Army, the senior officer of that grade, and assigned to command the District of Louisiana. As a result of his heroic military career with the United States Army during the Mexican War and as a result of him being presented with this sword, Abraham Lincoln called him the “Benedict Arnold of the South” for his defection to the Confederate States of America which he considered a treasonous act. When General Benjamin Butler captured New Orleans early in 1862, he sent a detail to capture General Twiggs. Twiggs escaped; however, Butler seized as trophies three wonderful presentation swords. Butler recommended that to show the folly of secession, the three swords should be donated to Congress, West Point, and the final one, this Congressional presentation, to be given to President Lincoln. In an excerpt from Lincoln’s letter to Congress : “I have in my possession three valuable swords formerly the property of General David E. Twiggs”. These swords were eventually all placed in the U.S. Treasury Department until 20 years after the war. Twiggs’ grandson filed suit to have them returned. In advanced age and in ill health, he soon was for all intents and purposes retired and died of pneumonia near Augusta, Georgia on July 15, 1862. We know of no other Civil War sword associated with Abraham Lincoln. Two acts of Congress were required for the return of this sword to the Twiggs family. The presentation plaque on this sword is engraved “Presented by President of the United States agreeable by resolution of Congress to Brig. Gen. David E. Twiggs in testimony of the high sense entertained by Congress of his gallantry and good conduct in storming Monterey. Resolution approved March 2, 1847.” Below this presentation are two gold plaques. One 3″ x 1″ in gold, raised relief depicting a battle scene showing infantry and cavalry charging past Mexican cannons during the storming of Monterey. Beneath this raised panel is a 4″ x 1″ engraved gold panel showing finely detailed soldiers—over 100 in all in this tiny panel—showing American flags and cannons firing. The large, 2″ langet in solid gold relief shows the storming of the fortress at Monterey. Above the langet, and beautifully engraved, are four gold straps decorated with floral, military motifs, including cross cannons and halberds, are interspersed with four mother-of-pearl panels with precious stones and gold studs. Topping the pommel of this sword is a solid gold American eagle, almost 2″ long and 1″ high, overlooking the battle scenes below. Also accompanying this fabulous sword is a wonderful painting of Gen. Twiggs done in 1855 by John W. Dodge. The painting was executed in July 1855 and is so inscribed. The painted image is approximately 6″ x 9″ on cardboard and is mounted in an elegant gold frame. Together, the sale of this unique and historically important sword and portrait is destined for the record books. In the world of fine art and antiques this moment in American auction history will be reported worldwide. CONDITION: 31-1/4″, double-edge, central fullered blade exhibits most of its original frost. Blade is in extremely fine condition with scattered areas of black staining. Gold and mother-of-pearl mounted hilt appears excellent in every regard. The only defect discernible is the broken and missing wing of the eagle on the reverse side of pommel. The eagle’s obverse wing also exhibits a hairline crack, but it is still solidly attached and has no chance of breaking unless hit with a severe blow. Mother-of-pearl slabs are so often chipped, cracked, and damaged, especially when exhibiting so much cutting and insetting. Only one small crack occurs in mother-of-pearl in upper-right panel. Sapphires and diamonds appear perfect. Topaz has a chip in its upper quadrant. Scabbard body is perfect with just scratches and scuffs. Mounts show light wear only at the highest spots. The bottom left floral decoration of the frame surrounding the presentation is worn showing silver where gilt has worn or been rubbed off. The solid gold, fluted drag exhibits some light scratching and denting on its reverse side. 4-31482 CW16 (750,000-1,000,000)

HISTORIC AND IMPORTANT ABRAHAM LINCOLN PRESIDENTIAL PRESENTATION FIREARM TO SENATOR J. J. CRITTENDEN, ONLY ONE OF TWO KNOWN LINCOLN PRESNETATION FIREARMS. THE ONLY LINCOLN PRESENTATION FIREARM EVER SOLD AT PUBLIC AUCTION. SN 593. A once in a lifetime opportunity one of only two known Lincoln presented firearms and the only one in private hands. This early production 2nd Model Burnside carbine, serial number 593, was presented to John J. Crittenden, former Governor of Kentucky, Attorney General and Senator. The presentation is inscribed on an engraved oval 3″ x 1-1/2″ silver plaque which reads, “Presented to the Hon. J. J. Crittenden by A. Lincoln, President of the United States as a testimony of affection and regard for his long and patriotic service, for which a grateful people bear willing testimony. February 1, 1862” Lincoln, is known to have presented only two guns; the other being a cased pair of Colt Revolvers presented to the Sultan of Turkey during his administration (this particular pair of pistols are possibly the most valuable American guns known. A $5 million offer was purportedly made for these guns prior to their donation to the Metropolitan Museum of Art) Crittenden, a good friend of Lincoln, and one of America’s most prominent and defining Politicians was born in Kentucky in 1787, his father having emigrated there following the American Revolution. He was educated in Kentucky, as well as at William and Mary College in Virginia. Having studied law, he began his practice in 1807, and quickly became the best known lawyer in western Kentucky. He also turned his attention to politics, and beginning in 1811, he was elected to the state legislature for six successive terms. He was chosen speaker of the House in 1815 and 1816. During these years, Crittenden also performed military service in the War of 1812, receiving a special governor’s commendation for his actions during the Battle of the Thames. Following the war, Crittenden served for two years in the United States Senate, before returning to Kentucky in 1819 to practice law. The internal political strife in Kentucky between the Old Court and New Court factions, however, drew Crittenden back to politics. Siding with the conservatives, he reentered the legislature, where from 1829-32, he was again speaker of the House. In national politics, he aligned himself with Henry Clay and the administration of John Quincy Adams against Andrew Jackson. Beginning in 1835, with his election to the United States Senate, Crittenden’s political career was generally connected with the federal government. He was a leading Whig opponent of the Jackson and Van Buren administrations, and after campaigning aggressively for the Whig candidate, William Henry Harrison, in 1840, he was appointed Harrison’s attorney general. Harrison’s death, followed by President John Tyler’s conflict with the Whig party, brought about Crittenden’s resignation in September 1841. He reentered the Senate the following year, where he opposed the annexation of Texas. Following the Mexican War, he abandoned Clay to support the nomination of GeneralZachary Taylor in 1848, whom he considered more likely to win. Crittenden’s action ended his long friendship with Clay. While Crittenden did not accept a cabinet post in the Taylor administration, he agreed to serve Taylor’s successor, Millard Fillmore, as attorney general, holding the post until the end of Fillmore’s term. Two years later, in 1854, he was elected again to the Senate. The reopening of the slavery question with the Kansas-Nebraska Act disappointed Crittenden, who regretted the abandonment of the Missouri Compromise. Reflecting his border-state and conservative character, he stood for any course that would restore sectional peace. He considered the possible dissolution of the Union as “the greatest evil” that could befall the country. In the election of 1860, he supported the Constitutional Union party ticket. Following Lincoln’s election, Crittenden introduced in the Senate his propositions, the most important of which restored by constitutional amendment the Missouri Compromise line. Known as the “Crittenden Compromise” he was unable to gain passage of his proposals or to get a popular referendum on them. He also failed in his efforts to secure adoption of the program of the Peace Convention which assembled in Washington in February 1861. Compromise having failed, Crittenden returned to Kentucky, where he actively sought to keep the state from seceding. On April 17, just days after the bombardment of Fort Sumter, Crittenden again urged his state to remain in the Union. Kentucky’s divided loyalties were reflected in Crittenden’s own family; two of his sons would lead opposing armies during the Civil War. Kentucky ultimately refused to join the Confederacy, and Crittenden was elected to the Congress, where he introduced resolutions to the effect that the war was to preserve the Union, not to interfere with slavery or to subjugate the South. As the war took a different course, he opposed the confiscation acts and the Emancipation Proclamation. He was preparing to run for reelection to Congress in 1863, when he died in Frankfort, Kentucky. It is surprising that Abraham Lincoln, one of America’s most revered Presidents and a firearms technology aficionado chose to only present two firearms during his administration. Obviously the set of Colts were a diplomatic gift. The presentation of this important and historic carbine to J.J. Crittenden, however, is a testament to his admiration and respect for this stellar politician and friend. This gun is purportedly pictured and described in a reference book on Presidential firearms and was featured in a 2-page spread in the national collecting magazine “Man At Arms.” The provenance of this Burnside Carbine is irrefutable. This gun has been in the Crittenden family until recent times and was, for many years, on loan to the Kentucky Historical Society in Frankfort, Kentucky in a featured exhibition. This gun is directly listed in a Crittenden will which is illustrated here. This gun is accompanied by a presentation trunk to J. J. Crittenden . The large, early, rectangular mahogany trunk is 38” long x 24” wide x 19” deep sitting on four 1-3/4” tall feet. Lid is 4-1/4” thick and it has a fine, large, mortised brass lock in front with a rectangular escutcheon screwed to the face. Center of lid has a 4-1/4” x 3” brass plaque inscribed “JOHN J. CRITTENDEN”. Interior was, at one time, lined with royal blue velvet, most of which has deteriorated and been removed. Inside of lid has been reinforced with application of a 1” x 3” board screwed beneath a crack in top. Apparently it originally had a lid stop in left rear corner which is now missing and there are two locator pegs on front edge. Corners are all beautifully dovetailed. Also accompanied by a volume The Crittenden Memoirs, H.H. Crittenden. Inside cover is a newspaper clipping relating that Col. Henry Huston Crittenden of Kansas City, Missouri, visiting Owensborough, Kentucky as the guests of Mr. & Mrs. Thomas M. Galey. The flyleaf is inscribed in ink to “Mr. & Mrs. Thomas Mellon Galey, in memory of a delightful visit to their home in Independence Kansas. With sincere best wishes Henry Huston Crittenden March 18, 1938”. On following page is a newspaper clipping from the Kansas City Star March 4, 1943 regarding the death & obituary of Col. Crittenden. On the dedication page is a long note signed “Thomas M. Galey” regarding the November 2, 1938 visit of Col. Crittenden to Owensborough. The volume is a total of 542 pages including index. This particular carbine was very popular in the early days of the War. Only about 2,000 of the Second Model carbines were made, and most were well used and worn. At the beginning of the war, many of these Second Model Burnsides were being used by the Rhode Island Cavalry, which saw action as early as the Battle of Manassas. Also issued these guns were the 1st Maine, the 1st New Jersey, and the 1st Pennsylvania Cavalries. The .54 caliber Burnside carbine was designed and patented by Ambrose E. Burnside and the Second model was manufactured in Rhode Island by the Bristol Firearms Company A total of five different models were manufactured during its years of production. Lowering the trigger guard, which also served as the operating lever, would cause the breech to tilt up, revealing a cone-shaped cavity. The metallic cartridge for the Burnside, of a unique cone shape, was placed into this cavity. Closing the lever rotated the breech block into position, placing the cartridge in the chamber. A percussion ignition system with an external hammer fired the carbine. A small hole at the base of the cartridge would allow the fire to pass through and ignite the powder in the case. Ambrose Burnside, the inventor of this carbine, eventually rose to the rank of Major- General in the Union Army during the Civil War. His record as a commander is not well known due to dismal record of success on the battlefield. CONDITION: Metal surfaces overall are brown, untouched with scattered light pitting, especially around nipple and breech. Rifling in bbl is very good. Stock is sound with scattered scratches, retaining proper inspector’s cartouches. Silver plaque, applied with four silver pins, is cleaned; however, shows original patina in the several dents and in the protected areas around pins. Trunk is in good to very good condition. Lid has a 1/4” wide separation which is supported on inside by the aforementioned board. It also has several grain checks and retains most of a fine restored finish. Book is fine, the brown cloth cover shows corner wear with a minor stain or two and some yellowing to pages. Spine is sound and book is in good shape. 4-314834-31610 CW17 (400,000-500,000)

CONFEDERATE DANCE ARMY REVOLVER. SN 40. Cal. 44. Dance brothers, in their Columbia, Texas factory, made about 350 Army and Navy revolvers during the Civil War. About 100 of these guns are known to exist today. The dance Army revolver is the only primary Confederate revolver made in 44 cal. It is also the largest Confederate revolver made. The dance Army is made in the style of the Colt Dragoon which was so popular with Texas troops in the Mexican war era. The most distinctive feature of dance revolvers is the lack of recoil shields on their frames. SN 40, which you are bidding on here, is a fine example. This gun was once in the collections of Sam Harrington and later Charlie Schreiner III, a great Texas collector. This gun is serial numbered in all places normally serial numbered on Dance Armies and appears orig in every regard. This gun functions well but mainspring is a bit weak. Surfaces are smooth, edges are sharp, and serial numbers are well struck and distinct. Dance revolvers saw hard use in the Civil War, this gun was used showing only minor muzzle wear with crisp front site and would make a fine addition to any collection. CONDITION: Cleaned metal surfaces are gray/black with scattered scratches, nicks, and pitting. Brass has been cleaned. Stocks are solid and fit well with numerous small dings and dents on bottom. An initial “B” is carved on right stock. Two screws in trigger guard appear replaced. 4-32950 JS505 (40,000-60,000)

HISTORIC INSCRIBED COLT SECOND MODEL DRAGOON REVOLVER INSCRIBED TO (CONFEDERATE GENERAL) JOSIAH GORGAS. SN 9327. Cal. 44. Martially marked Second Model Colt Dragoon Revolver with 7-1/2″ oct to rnd bbl, brass triggerguard & backstrap and 1-pc walnut grip. Backstrap is inscribed in period script “To Lieut. Josiah Gorgas / From his Fellow Officers.” Josiah Gorgas was a native of Dauphin County, Pennsylvania, born in 1818 and graduated from West Point in 1841. He worked in the Ordnance Corps, throughout his military career being commissioned a Lieutenant on March 3, 1847 in time to serve in the Mexican War. He served during the siege of Vera Cruz and thereafter, commanded the Ordnance Depot during Scott’s march on Mexico City. It was during this time that this historic inscribed Colt revolver was presented to him. After the Mexican War, he took charge of a number of arsenals and married the daughter of a former Governor of Alabama in 1853. Gorgas was promoted to Captain in 1855 and served in Charleston, South Carolina until 1860. Upon the opening of the Civil War he resigned his commission in the Union Army & defected to the Confederacy. President Jefferson Davis appointed him Chief of the Ordnance Department with the rank of Major. Gorgas was responsible for importing arms & ammunition from England to the Confederacy as well as utilizing captured machinery & contracting arms manufacture to a variety of contractors. He was specifically responsible for turning Richmond’s Tredegar Ironworks into an arms manufactory. Gorgas was an impressive Ordnance Chief creating an efficient department operating on limited resources and on November 19, 1864 President Davis appointed him Brigadier General. Gorgas was so efficient, in fact, that at no time was the Confederacy seriously short of armament, only the men to utilize them. Following the War, Gorgas was the superintendent of the Briarfield Ironworks and later became involved in education ultimately accepting the Presidency of the University of Alabama. Josiah Gorgas died on May 15, 1883. Gorgas’ contributions to the Confederate war effort had never been undervalued, literally turning plowshares into swords. This historic Colt revolver, obviously a valued sidearm, is one of the most important Colt revolvers to come to the open market in recent years. Accompanied by a wonderful & rare period flap holster with belt loop, built in Confederate style, especially for a dragoon. Gorgas’ career is detailed in a book, Plowshares into Swords, Van Diver, from Texas A&M University. CONDITION: Very good, all matching including grip. All metal surfaces are a deep plum/brown color with light surface pitting on the bbl & frame. No cylinder scene remains. Grip is fine with chipped toes showing moderate to heavy wear and retains 60-70% strong orig varnish. Mechanics are fine, strong sharp dark bore. Holster is fine having been treated, is now soft & supple with heavily crackled surface and a couple of minor tears at base of flap. Toe shows very heavy wear, missing its plug with a tear by seam on bbl end. 4-32952 JR339 (50,000-100,000)

THE FINEST PAIR OF CONSECUTIVE NUMBERED, CONFEDERATE MANUFACTURED PISTOLS KNOWN, RIGDON & ANSLEY. SN 1774 & 1775. Cal. 36. Rarely are Confederate handguns found with orig blue finish. These two Augusta, GA made guns exhibit as much as 50% orig bright finish and traces of case color. Both guns are orig and authentic in every regard with fine inspection marks of Wescom Hudgins. Both guns are well fit, properly serial numbered on every part normally serial numbered. Several casting flaws, often present on Confederate manufactured arms, are visible in cyl and bbl housing of SN 1775. Only about 7,500 Confederate revolvers were made by all manufacturers and less than 1000 by Rigdon & Ansley. There are few consecutive pairs of any Confederate guns known. We sold a consecutive pair of Griswolds in NRA fair condition for $80,500 in our March 2004 auction, and these are vastly superior in condition and rarity. These guns, in excellent condition, are about as fine as any single gun that can be encountered in Confederate revolvers, much less this exceptional, high condition, consecutive pair. If you want to own the finest consecutive pair of Confederate handguns in existence, this will be your only chance to do so. CONDITION: Fine overall. All iron parts retain bright blue finish, some turning to black. Actions are crisp. Nipples show little wear. Brass parts show good patina. 4-31237 JS230 (150,000-175,000)

HISTORIC AND EXTREMELY RARE AND FINE CONDITION CASED GRISWOLD CONFEDERATE REVOLVER IDENTIFIED TO A SURGEON IN THE 25TH SOUTH CAROLINA INFANTRY. SN 663. This is possibly the finest condition 1st Model Griswold known and the only original cased Griswold revolver. A wonderful identified classic brass frame Confederate revolver with a rich history. This Griswold revolver produced in Griswoldville, GA, serial number 663 is a brass framed copy of the Colt Model 1851 revolver with a 6-shot round cylinder, dragoon style barrel, octagon to round with one-piece walnut grips and a brass frame, trigger guard and back strap. The serial is stamped in large numbers on the right side of the frame, right side of the barrel housing, on the cylinder and “63” on the loading lever. The revolver is accompanied by its original walnut case, similar to a Colt revolver style case measuring 14-½” X 6-¼” X 2” with a diamond shaped key escutcheon on the front. The segmented interior, without accessories, is lined in velvet. On the bottom of the case, in period pencil, is “S. Logan, M.D./Richmond/ Va.” This revolver is identified to Surgeon Samuel Logan. Logan saw service throughout the entire war. He was appointed on July 19, 1861 and was paroled at Greensboro, NC with Johnson’s Army on May 1, 1865. Serving off and on as Chief Surgeon of the 2nd and 3rd Military Department, C.S.A., throughout most of the war he served in the 25th SC Infantry, also known as the Eutaw Regiment of Hagood’s Brigade. The Twenty-Fifth SC was organized during the winter of 1861-1862 with men from the 11th Battalion who were from Charleston. Under the command of General Johnson Hagood in September, 1863 the 25th Regiment was deployed in the defense of Charleston for much of the war. The 25th Regiment was mustered into Confederate service on 22 July 1862. Hagood’s Brigade served on the islands adjacent to Charleston until May of 1864. They were stationed at Camp Pemberton on James Island and rotated with other units to Fort Sumter, Fort Johnson, Fort Lamar at Successionville, Wagner Battery and Gregg Battery on Morris Island. Some of the members of the 25th Regiment were captured on 7 September 1863 at the fall of Battery Wagner(Fort Wagner). Upon being sent to VA during the spring of 1864 following the Charleston campaign the regiment numbered 764 men. The 25th Regiment played a major role in the defense of Petersburg, including the battles of Drewry’s Bluff, the Bermuda Hundreds, Cold Harbor, Walthall Junction, The Battle of the Crater, and the Battle of Weldon Railroad. At Weldon Railroad there were 2 killed, 29 wounded, and 70 missing. After the disaster at Weldon Railroad on 21 August 1864, the 25th Regiment participated in the engagement at Fort Harrison. By late 1864, Wilmington, NC was the only surviving major seaport in the South. In December of 1864 the 25th Regiment was sent to Wilmington, NC to help defend Fort Fisher that protected the blockade runners bringing imported munitions and supplies vital to the Confederate army waiting at the VA front. Many of the 25th S.C. Infantry were captured during the fall of Fort Fisher. The 25th Regiment was surrendered by General Joseph E. Johnson at Durham Station, NC on April 26, 1865. Surgeon Logan was paroled on May 1, 1865. CONDITION: Fine with a wonderful dark patina overall. Blue turning plum overall. Markings are clear, edges sharp but showing moderate wear. The right side of the bbl housing shows a number of scattered nicks. A few casting flaws are found principally on brass parts but the iron parts have only small areas of peppery pitting here and there. Revolvers identified to surgeons from the North or South are extremely rare and this may also be the only known cased Griswold & Gunnison in existence. An attractive Confederate revolver with an excellent provenance related to an important SC surgeon. The revolver is accompanied by a large file of photocopied archival records. 4-31238 CW4 (50,000-75,000)

GRISWOLD REVOLVER SN 2929. Cal. 36. You are bidding on a fine all orig Griswold revolver. The serial number occurs on all parts normally numbered. The secondary number “19” occurs on all parts normally numbered including the right bottom of stocks. A cryptic “D” is found on various parts including bottom of bbl and back of cylinder where this mark is often worn and indiscernible. A Roman numeral “II” is found internally on the brass parts. If you want just one nice Confederate handgun, this could be the one. This is a fine all orig example of the largest Confederate revolver manufacturer; Samuel Griswold. CONDITION: Metal surfaces are gray with scattered staining and pitting. Mechanics are good. Brass is smooth with scattered scratches and nicks. Stocks are well fit with scattered scratches and dings. 4-32949 JS507 (20,000-30,000)

IDENTIFIED GRISWOLD 1ST MODEL REVOLVER, SN 518. Cal. 36. First models of all revolvers, especially in the first 700 guns, have a lower survival rate than other Griswold’s. These earlier guns according to some experts were made by different workers in the later production guns. These guns lack Roman numerals but otherwise are similarly marked to later first model and standard production guns. This gun exhibits serial number “518” on cylinder, bbl housing, and frame on the right side. A secondary number “18” is found on triggerguard, backstrap and correctly penciled inside stocks. A cryptic “B” is found on the brass parts but is not discernible on cylinder or bbl. All major parts of this gun are orig with several screws, mainspring, and wedge being replacements. A name “W. A. JONES” is stamped on bottom of back strap. While trying to research who W. A. Jones could be; a Confederate soldier with this name shows up in most every Confederate state. CONDITION: Metal surfaces are black with pitting. Serial numbers are discernible, weak on bbl housing. Brass is cleaned showing numerous nicks, scrapes and scratches. Stocks are sound as refinished with several chips a crack on right side. 4-32951 JS508 (15,000-20,000)

GRISWOLD CONFEDERATE REVOLVER. SN 2347. Cal. 36. SN appears on bbl housing, cyl, and frame. Secondary number “7” appears on loading arm and triggerguard. Wedge appears to be Colt and has 5-digit SN, though it appears orig to this gun’s time of use based on colour and condition. A cryptic letter “C” occurs on bottom of bbl near latch, frame, triggerguard, and backstrap. Roman numeral “IIII” is cut into triggerguard and backstrap. With exception of a couple screws and mainspring, gun appears to be all orig and authentic. CONDITION: Metal is gray/black with numerous dings, scratches, and scrapes. Brass is cleaned with numerous scrapes, dents, and scratches. Left side of stock has an area carved, such that thumb better fits grips and has small repair. 4-32918 JS228 (18,000-22,000)

AUGUSTA MACHINE WORKS PISTOL POSSIBLY CARRIED ON THE CSS SHENANDOAH . SN 24. Cal. 36. This Confederate made copy of a Colt Navy revolver, with 8” fully oct bbl, is thought to be a product of the Augusta Machine Works in Augusta Georgia. This fine inscribed gun was in the collection of David Cline who displayed his massive collection for many years along the walls of his bait shop in Eau Galley, FL. Many marveled at Cline’s enormous collection from cap guns to Henry rifles and this Confederate handgun among others. He bought and traded for guns for many years until his collection was auctioned in the mid-1990s. This was probably the most significant historical gun as we know of no other Confederate arms from the CSS Shenandoah. “H Canning”, which is engraved on backstrap, is a sailor listed on the Shenandoah late in the Civil War. Augusta Machine Works pistols are thought to have been made late in the war based on other identified examples and finding an identified gun from the CSS Shenandoah, which sailed for months after the war officially ended, would make sense for a sailor in 1865 to have acquired such a gun. There are a couple variations of Augusta pistols: one having thick bulging grips, and the other, like, having slimmer grips like this one. Augusta’s can have 6 or 12 stop cylinders – this one has six. This is a fine example that appears to be orig throughout. Like so many guns of this pattern, serial numbers or cryptics appear infrequently on the gun. This gun exhibits serial number “24” on the unloading arm and inside the recoil shield. A number “2” is found on the back of the cylinder. There are two other nearly identical guns to this including serial number “61”, which was once in the Ted Meredith collection. Letters of provenance accompany this gun from the buyer from the Cline auction a letter from Ted Meredith stating his opinion as to the guns authenticity. There are probably less than 20 examples known of all Augusta machine Works variations and this is a fine one. CONDITION: Metal surfaces smooth and gray overall with scattered scratches and pitting. Mechanics are very good. Stocks are solid & well fit with scattered scratches and nicks. 4-32944 JS506 (30,000-40,000)

HIGHEST SERIAL NUMBERED RIGDON AND ANSLEY KNOWN. SN 2373. Cal. 36. Rigdon and Ansley Augusta, Georgia made Confederate revolver serial number 2373 was discovered in Texas in about 1995. No authorities knew about this gun until then (published serial numbers in texts only go to 2359). This gun appears all orig and is properly serial numbered in all places where serial numbers normally are found. In the very late serial numbers of these guns, wedges are found with no springs and this wedge is of that type and though it is not serial numbered, it appears correct. The loading latch is not serial numbered and appears to be a period replacement. The grip’s profile is slightly different to earlier produced Rigdons in that these are slightly slimmed at frame. The CSA markings on bbl are especially deep and well struck. You are bidding on one of the last revolver’s made in the Confederacy and it is a fine example. CONDITION: Metal overall is gray with scattered scratches and dings. SN on triggerguard is partially obscured as can be seen in photos. Only the first three digits of the serial number on cylinder are visible. 4-32943 JS500 (25,000-35,000)

SPILLER & BURR REVOLVER REVOLVER WITH HOLSTER AND BELT. SN 190/387. Cal. 36. This scarce low serial numbered Spiller & Burr revolver is accompanied by a great Confederate flap holster and roller buckle belt. This gun was once in the collection of Fred Edmunds and he states in his accompanying letter as follows: “David J. Burr, of Richmond, Virginia, was an enterprising gentleman whose company had built a locomotive (1836) and a steam packet named the “Gov. McDowell”, which navigated the James River and the Kanawha Canal (1842). In 1880, he is listed as a commission merchant in Richmond. Also a commission merchant but established in Baltimore, was one Edward N. Spiller. Being of strong Southern leanings, Spiller moved to Richmond in 1861, where he joined forces with David Burr and a Lt. Col. James H. Burton, to manufacture revolvers for the Confederacy. James H.. Burton was born in Virginia and was educated in Pennsylvania, apprenticed in a Baltimore machine shop, and in 1844, went to work at Harper’s Ferry Arsenal where he became a foreman a year later. He was a mechanical genius: he then became a master armorer (1854). He became chief engineer of the Royal Small Arms Factory at Enfield, England, where he remained until 1860 when he returned to Virginia, and was commissioned Lt. Col. in the Ordnance Dept., and placed in charge of the Virginia State Armory. Upon the capture of Harper’s Ferry by the Virginia Militia, Burton took charge of the removal of the rifle and musket-making machinery to Richmond. Muskets were made there for a short time by the State of Virginia under Burton’s supervision, before the machinery was “loaned” to the Confederate Government. Spiller, Burr and Burton became partners, with the latter securing a contract with the Confederate Government for the manufacture of 15,000 revolvers (navy size). The contract date was Nov. 30th, 1861, but was renegotiated and made anew March 3, 1863, for the same 15,000 revolvers. The pistol factory was removed from Richmond to Atlanta in May of 1862. Falling far behind in production, the Confederate Government bought out Spiller & Burr near the end of 1863, and moved the operation to the Macon Armory, with Burton commanding. The manufacture of pistols continued without a break in serial numbers. Production continued in fits and starts from August, 1864, on through the following months until mid-November when, because of enemy operations, a move was made to Columbia, S.C. After that time, some pistols were assembled from parts, and some small parts were made until near the end of the war. The Spiller & Burr revolver was copied from the US Model Whitney Navy, which was made in New Haven, Connecticut. The Whitney, of course, had an iron frame, while the Spiller has a brass frame, backstrap and triggerguard. Most Spiller parts have serial numbers, although such numbers are often omitted from the loading lever assembly. Spiller frames are generally stamped with a “C.S.” (sometimes on the right side, sometimes on the left, sometimes upside down!). Less than half of the Spillers noted have serials on the cylinders. Examination, Description and Authentication of Spiller & Burr #190 The overall look of Spiller # 190 showa a pistol with an even brownish patina: a most pleasing appearance and an expected one for an original untampered-with specimaen. The one-piece solid brass frame, backstrap and triggerguard show a most pleasing patine, as does the upside-down “C.S.” stamped at the lower left side portion of the frame. Barrel is 6 and 7/8 inches long in its entirety, and protrudes 6 inches from the frame, which is the correct length: it has its original brass post front sight in excellent condition. The octagon barrel is correctly crowned at the muzzle. The serial number 387 is stamped on the bottom flat of the barrel about an inch form the frame. The barrel is 100% original Spiller & Burr and stamped with the correct dies. The triggerguard-plate, which fits into the frame, is also made of brass, and is stamped 190 at the front, as is the bottom right inside surface of the frame. The same 190 is stamped at the inside left surface of the backstrap where it meets the butt. The usual brass casting flaws are evident on the inside surfaces of the backstrap. There is an “E” stamped on the inside surface of the forward portion of the backstrap. The serial #190 is stamped also on the bottom outside surface of the buttstrap. The original iron pin which functions as a stabilizer for the grip halves, is present. As is often the case with Spillers, the original mainspring is thin at the base and has an iron wedge in place as a stabilizer filling in the cut-out in the frame. Some Spillers have wider main-springs. The original walnut two-piece grips have some dongs and minor dents, but fit perfectly, showing surprisingly little shrinkage. They are most attractive with their brass escutcheons and iron screw holding them in place. “190” is pencil;ed-in on the inside of the left grip. The unnumbered original cylinder shows a most pleasing patina which matches perfectly the remainder of the gun: it is in excellent condition with its original percussion nipples intact. Also original in every respect, but unnumbered is the loading lever assembly, very similar to the Whitney revolver, from which it was copied, of course, but far more crudely made and finished: unnumbered loading lever assemblies in Spillers are often observed, prompting many collectors to question their originality and giving rise to the suspicion of replacement. More often than not, such feelings are unwarranted. The loading lever assembly has the same pleasing patina as does the original hammer (both having originally been casehardened). Loading lever catch is original and inlets into the barrel precisely. In so far as it is possible to determine, all screws appear to be original. CONCLUSION Spiller & Burr #190 is an excellent example of one of the rarest Confederate manufactured handguns. It is in original untouched condition, having an aged patina overall. Pistol #190 was one of the 700+ guns made and assembled at the Spiller & Burr Atlanta factory before the operation was taken over by the Confederate Government and moved to Macon in late 1863, where some 600+ or – (more) were made or assembled. The observation that the serial number 387 appears on the bottom of the barrel, rather than the #190 serial on the remainder of the gun, should not be of any concern, for the reason that it is a Spiller barrel: its numbers are Spiller dies: post front sight and loading lever catch are original Spiller manufacture. The undersigned ahs observed at least twelve other Spillers where the barrel was stamped with a different number than the remaining parts. For example, one which readily comes to mind is Spiller #548, an excellent original Spiller which has its barrel stamped “488” with the large Spiller dies. Her again, #548 has its original barrel with its crowned muzzle: post front sight and loading lever catch are original. The reason for this mis-numbering? Possibly occurred at the time of assembly, either by mistake or because correctly-numbered barrel was defective. Another theory: Correctly numbered barrels might not have passed inspection and were discarded. Remember, serial numbers were only important to the Confederate gun makers to aid them in fitting together the various parts: function was their goal. Thus, Spiller & Burr #190 takes its place as being one of the approximately 1300 revolvers made by that company, joining the small overall production of what are considered to be the primary Confederate handguns: Griswold & Gunnison, 3600: Leech & Rigdon, 1500: Rigdon & Ansley, 900. A grand total 7306! With the high mortality rate of Confederate handguns, combined with the hard use they generally received rendering most in poor condition, Spiller #1990 is truly a collector’s Treasure! Frederick R. Edmunds Curator Gettysburg, Pennsylvania December 1, 1998″. CONDITION: Metal surfaces gray with scattered pitting. Loading assembly is possibly replaced since there are no serial #s. Brass is patinaed with scattered scratches and nicks. Stocks are well fit and exhibit scattered scratches and dings. Holster & belt are solid & sound with some crazing to the holster and new black dye added to flaked areas. 4-32947 JS509 (20,000-25,000)

SPILLER & BURR CONFEDERATE REVOLVER. SN 67. Cal. 36. This rare, early serial numbered Spiller & Burr is marked “CS” on right side of frame, and “Spiller & Burr” is stamped on top bbl flat. SN is found on bbl, cyl, frame, and base pin. Loading assembly must have broken on this gun, and the soldier continued to use it by improvising a solid end where loading assembly once was. Stocks, when removed, have a date, a name, and other barely discernible writing. Further research may ascertain identity from these markings. CONDITION: Metal surfaces are gray/brown. Brass has been cleaned and has numerous scratches and dings. Stocks are dented, with several cut notches in each, and a 1” x ½” sliver is missing from toe of left stock. Cyl appears to have old repair which is pitted and rusted. Action does not work. Triggerguard is not serial numbered and is probably from a Whitney. 8-76223 JS229 (12,000-15,000)

COLT NAVY CARRIED BY CAPTAIN THOMAS CHUBB OF THE CONFEDERATE SCHOONER ROYAL YACHT. SN 23167. This wonderful condition model 1851 Colt Navy was recently found in the state of Vermont where Chubb died at his summer home in 1886. Chubb’s son had a business of manufacturing fishing rods and reels with the Thomas H. Chubb brand, which are highly collectible today. This business was near Chubb’s summer home in Post Mills, Vermont. The commemorative inscription on backstrap of gun reads “CAPT T. H. CHUBB, 1861-1865” and “CSN ROYAL YACHT” back of triggerguard. Accompanying this gun is a large folio of history which tells us more than has been published in texts on the Confederate Navy. Thomas Moebs, in his definitive Confederate Navy volume, knows little of Chubb’s life or service, though his record on the Royal Yacht and his exchange from Ft. LaFayette are mentioned. From the attached records; Chubb is listed as being Commodore “born in 1811 of good old Revolutionary stock and within the very shadow of the Bunker Hill Monument where his parents and grandparents lived”. Chubb in his 80th year “was one of the most sprightly participants in the Bunker Hill celebration which took place on June 17, 1890”. Thomas Chubb had a long history with the sea and various navies. “Mr. Chubb left his Puritan Home when a mere boy, contrary to the wishes of his parents, and engaged as cabin boy on a coasting schooner, next on board of a man of war, and was soon a full fledged seamen. When the United States squadron was ordered to the Mediterranean in 1827, Chubb was numbered among the crew of the flagship JAVA under the command of Commodore Crane. A call for volunteers to man the US schooner PORPOISE against the Greek Pirates that were preying upon American merchant men in the Mediterranean was responded to by Chubb. The cruise offered sufficient site of bloodshed and carnage to fully appease the young man’s desire for naval combat. In 1838, Captain Chubb, then in the very prime of manhood and abundantly supplied with wealth, became so earnestly aroused in behalf of the Texans in their struggle for independence that he loaded the Brigg, CECELIA, with munitions of war and sailed for Texas In 1839 he established a head-right in Texas, his family joining him the same year coming from Massachusetts. He was appointed superintendent of public construction by Sam Houston (who was a warm friend of the Captains) He continued in this service until the outbreak of the Civil War, when the association’s pilot boats were all captured by the blockading fleet, excepting the Royal Yacht. Though an Eastern man by birth and education, he was a Southern man by adoption and inclination; at the secession of his state he took up arms in defense of his rights and his property with the same determination that characterized his whole life. He was one of the first men afloat in the Confederate Navy, and his vessel, the ROYAL YACHT played an important part through the entire war”. Captain Chubb was involved in the capture of the federal steamer STAR OF THE WEST which was taken as a prize and sent to New Orleans. The Royal Yacht was commissioned on the 9th of September 1861 and was attacked by the enemy on the eighth day of November following. This attack, near Galveston, from the USS Santee overwhelmed Captain Chubb 100 U.S sailors to 13 aboard the ROYAL YACHT. When the attack was first made, there were only two men on the deck, one of whom was slightly wounded. The noise of the attack soon brought Captain Chubb and Captain William Saunders to the deck and they alone stood combating against a hundred men. The fight was a desperate one and lasted until all the means of defense on the YACHT were exhausted. Their shots had told with effect on the enemy, killing seven of them, and wounding eight others, some mortally”. Captain Chubb was placed on the Santee, transported to New York where he and his men were marched in irons through the streets…. they were afterward sent to Fort Lafayette….. Chubb was later exchanged….” and upon arriving in Texas he was met by any most cheering reception by the citizens of Houston and was asked to tell the story of his capture and confinement…..Upon reaching Galveston…. was lionized as hero of one of the most gallant fights of the war. It was this engagement that gave Jewett his promotion and cost the warmest friendship between Admiral Jewett and Commodore Chubb. Commodore Chubb continued in the fight as long as there was a ray of hope left, and contributed freely of his ample means. But when Lee surrendered he was among the first to step back to the old standard of the Stars & Stripes….. soon after the close of the war he was appointed by Mayor Bolton and Alderman of the city of Galveston to the office of harbor master at the port of Galveston which office he held until his death” at his summer home in Vermont. Chubb is buried in Galveston, Texas. CONDITION: This gun is mechanically fine, tight with sharp edges in as found condition. Gun overall is gray with scattered pitting over 20 or 30% bright blue on bbl. Cyl scene is complete but with scattered pitting. Backstrap and triggerguard retained a portion of their silver-plate. Stocks are very good with much orig varnish, a small chip is present on inside toe of left stock. 4-32838 JS352 (10,000-20,000)

SCARCE TRANSITION FIRST MODEL PARIS LEMAT. SN 663. Cal. 10.6 mm/16 ga. Usual configuration with 6-3/4″ oct bbl, dovetail brass front sight, engraved on top flat “COL. LeMat Bte sgdg Paris”. It has rammer mounted to left side as with 2nd models. It has usual 9-shot cylinder. Smoothbore bbl is about 6-5/8″ threaded on the head for bbl boss attached to oct bbl. It has spring loaded bayonet, latch with spur trigger guard, 2-pc checkered walnut grips & a swiveling stud & lanyard ring in butt. Hammer nose is articulated with a rounded short stud from each side. These grapeshot revolvers were a favorite of the Confederate Cavalry and saw extensive use throughout Civil War. CONDITION: Good to very good, all matching including grips. Overall retains a smooth medium brown patina with some very fine pitting at muzzle end of bbl & on cylinder. Bbl slip ring, at cylinder end, shows welding repairs with some alteration on rammer pivot, which may be an old replacement. Oct bbl also shows some artificial aging. Grips are sound showing heavy wear. Mechanics are fine, strong dark rifle bore, lightly pitting smoothbore. 4-32945 JR335 (17,500-27,500)

FINE LONDON LEMAT GRAPESHOT REVOLVER. SN 8545. Cal. 42/16 ga. Usual configuration with 6-5/8″ oct bbl, with orig tall dovetail front sight and marked on top “LEMAT & GIRARD’S PATENT LONDON” with a smoothbore bbl/cylinder pivot mounted into frame. It has a 9-shot 42 caliber cylinder, missing one nipple. Loading lever is on left side of bbl and has a welded repair above pivot. It has a sliding pin bbl/frame connection and has checkered 2-pc walnut grips with a Fleur-de-lis proof on left raised panel. Front end of frame has assembly number “599” which number is also found on back of cylinder & inside face of bbl boss. Inspector or assembly number “02” is also found in this location and on rear of cylinder. This revolver, while not documented as a specific Confederate used sidearm, is only 39 numbers away from a known Confederate revolver, serial number 8584, which was used by Lt. Simeon Cummings of the C.S.S. Alabama to commit suicide or accidentally shoot himself on board the Alabama while in port in South Africa. This story is related in LeMat The Man The Gun, Forgett & Serpette. Accompanied by an early pine casing that may or may not be orig to this revolver. It has coarse green wool fabric lining that appears to have great age. Compartmented in bottom for revolver, an orig LeMat brass bullet mold with s[rue cutter for a conical bullet and two small rnd balls. It also has a small decorative brass & copper flask, what appears to be a maple handled orig nipple wrench with half of orig ebony cap and a turned maple tamping rod for shot bbl. It is generally accepted that the London LeMats are Confederate firearms. CONDITION: Fine, all matching. Bbl retains about 80% glossy orig blue with flaked areas a dark patina. Cylinder retains 60-70% flaked orig blue with its missing nipple. Frame is flaked to a medium patina with traces of orig blue. Grips show light wear and retain most of their orig oil finish. Rammer is orig with matching number its welded repair. Rifled bore is strong with moderate to heavy pitting. Shotgun bore has scattered spots of pitting. Case has a couple of cracks in lid and another in bottom and shows heavy wear. Interior is faded with moth damage inside lid with wear & soil in bottom. Flask is fine, mold is very fine. A rare set that would fit into anyone’s collection. 4-31115 JR201 (8,000-12,000)

FINE SECOND MODEL PARIS LEMAT GRAPESHOT REVOLVER. SN 1581. Cal. 10.6 mm/16 ga. Usual configuration with 7″ oct rifled bbl & 6-3/4″ smoothbore bbl/cylinder pivot. It has rammer mounted on left side with bbl engraved in script “Col Le Mat Bte s.g.d.g. Paris”. It has usual 9-shot cylinder with an articulated hammer nose by means of a central thumb lever. Mounted with 2-pc checkered walnut grips and has an integral lanyard loop in butt. These revolvers were a favorite of the Confederate Cavalry and saw extensive service throughout Civil War, especially by Gen. Beauregard who was a personal friend of Le Mat. CONDITION: Fine plus, all matching except grips which numbers could not be determined. Oct bbl retains 35-40% orig blue mixed with brown patina. Smoothbore bbl & cylinder retain a mottled dark brown patina. Frame retains 15-20% strong orig blue on bottom & top of frames and recoil shield. Grip frame, trigger guard & sides of frame are a dark smooth brown patina. Rifled bore bosses are stuck to smoothbore and will not unscrew although the smoothbore will unscrew from frame. Grips show moderate wear with a hand worn patina. Mechanics are fine, rifled bore is strong with moderate to heavy pitting; smoothbore is clean with fine pitting. 4-32955 JR336 (20,000-30,000)

RARE MURDAUGH CONFEDERATE NAVY CONTRACT PARIS LEMAT GRAPESHOT REVOLVER. SN 2431. Cal. 10.6 mm/16 ga. Usual configuration with 6-5/8″ oct rifled bbl with tall dovetail front sight, rammer on left side with small block letter address “SYSTme LEMAT Bte s.c.d.g. PARIS” and British proofs on lower left flat. Right side of bbl has LeMat’s star over “LM” logo. It has usual 9-shot cylinder with small British proofs between all of nipples with one stamped “M” for Confederate Naval Lt. William H. Murdaugh who was sent to London in 1864 to inspect & receive all arms for Confederate Navy. It has usual 6-3/4″ smoothbore bbl and standard hammer with articulated nose by means of a central thumb lever. It also has checkered 2-pc walnut grips with an integral lanyard loop in butt and trigger guard without spur. It is unknown how many of these Murdaugh inspected grapeshot revolvers were actually purchased but few survive today. CONDITION: Fine, all matching except rammer which is unnumbered and appears to be a fine replacement as are the rammer screw & latch. No orig finish remains being a thin, mottled, silver/brown patina on bbl and a smooth gray patina on cylinder & frame. Grips are very fine with moderate wear & a dark oil stained patina. Mechanics are fine, worn dark rifled bore, moderately pitted smoothbore. A rare Confederate revolver seldom ever encountered in any condition. 4-32946 JR337 (25,000-35,000)

TRANSITION LEMAT GRAPESHOT REVOLVER. SN 1002. Cal. 10.6 mm rifled bbl/16 ga. smoothbore. Second model configuration with 6-5/8″ oct bbl, high dovetail front sight with left side mounted replacement rammer that appears to be orig equipment but is not numbered. It has 6-3/4″ smoothbore bbl/cylinder pivot & usual 9-shot cylinder. It has second model style hammer with pivoting nose, broken thumb lever. It has first model bbl/frame latch and a spur on trigger guard with 2-pc checkered walnut grips & an integral lanyard loop buttcap. These revolvers were greatly favored by Confederate Cavalry & used throughout Civil War, especially by Gen. Beauregard. CONDITION: Good to very good, all matching including grips, except rammer as noted. No orig finish remains being a smooth worn gray patina with only traces of bbl inscription remaining. Grips have chipped heels, otherwise are sound, showing heavy wear with a dark oil-stained patina. Hammer is without half cock notch, otherwise mechanics are fine, very worn dark rifled bore and lightly pitted smoothbore. 4-33336 JR340 (7,500-12,500)

Revised: 10/19/2007

(Additional Information) We have been contacted by Doug Adams, noted author of The Confederate LeMat Revolver and he has indicated that early on LeMat had an inspector by the name of Chapman, although he does not know whether this is, in fact, the same early inspector, or not, however it would be an excellent topic for future research.

RARE PROTOTYPE OR EXPERIMENTAL LEMAT GRAPESHOT REVOLVER. SN 1945. Cal. 42/16 ga. Nickel finish with 6-3/4″ smoothbore oct bbl which was never rifled, usual tall dovetailed front sight with an uncommon tall fixed rear sight. Top flat is engraved in period script “Systeme Le Mat Bte sgdg Paris” surrounded by a line border engraving. Right flat has the serial number and Le Mat’s logo of a star over “LM”. It is very unusual in that it does not screw to the smoothbore bbl but simply slides on with a pressure fit in the front ring and is attached with a screw through the hole where link pin would normally be. Rammer on left side of bbl is about 1/8″ thick flat steel with beveled outer edge and a circular area which would contact bullet nose secured with a normal sized blued screw. It has usual 9-shot percussion cylinder with serial number on outer diameter and a simple incised line around the front edge instead of the usual raised, knurled rim.. Smoothbore bbl is 6-1/8″ long with only markings being serial number on right side at frame. Frame is slightly thinner in some places and trigger guard is also somewhat thinner. Trigger is also thinner with a lighter & shorter trigger guard. Hammer is about identical in contour to the 2nd Model LeMat revolver but it has an unusual articulated nose which is half exposed and without usual thumb lever. It has standard checkered walnut grips with screw from right side rather than usual left side. Bottom of each grip has inked serial number that appears to be “1701” and inside left grip is stamped “L. CHAPMAN” and inside right grip hand written in pencil is “L. CHAPMAN / COLLINSVILLE CONN”. It is readily apparent that Le Mat was experimenting with this piece but to this cataloger’s knowledge none of features found on this revolver were ever implemented in production. CONDITION: Very fine. Bbl & rammer retain most of their strong bright orig nickel with some flaking on left side and sharp edges. Pin retainer spring screw is missing half its head. Cylinder retains about 95-96% strong bright orig nickel. Smoothbore bbl, in exposed area, retains 93-95% orig bright nickel. Frame, hammer & trigger guard retain about 85% of their orig nickel with with most of the losses from heavy flaking on front & backstraps. Grips show light wear with a fine oiled patina. Mechanics are crisp, top bore is bright & shiny with a few spots of light pitting. Shotgun bore is fine with very fine pitting. Altogether a most unusual and rare revolver. 8-87519 JR210 (10,000-15,000)

EXCEPTIONALLY RARE CONSECUTIVE NUMBERED PAIR OF COLT MODEL 1860 FLUTED ARMY PERCUSSION REVOLVERS WITH CONFEDERATE USE. SN 1542 & 1543. Cal. 44. This extraordinarily rare pair of Colts was shipped to Confederate Maj. Gen. William Thompson Martin of Natchez, Mississippi on Jan. 17, 1861 in a shipment of 160 same type guns along with 80 attachable stocks and 80 flasks. General, at that time Colonel, Martin had ordered these to outfit his cavalry regiment with a pair of Colt revolvers, a stock, a flask & a pair of saddle holsters. This is documented in a Colt factory letter as stated above, a copy of which, for serial number 1542, accompanies this lot. Apparently serial number 1543 is a “no record” at Colt. The likely reason is that they were shipped as a pair and therefore not recorded. Col. Martin, prior to beginning of the Civil War, was the 1st Lieutenant of the Natchez Guard. When the war opened he organized and was elected Captain of the Adams Troop of Cavalry. The Adams Troop was made up of some of the wealthiest men of Adams County & purchased the finest weapons & equipment. Each man had two fine horses and brand new uniforms. After the firing on Fort Sumter, Capt. Martin & his Troop chartered a steamboat to Memphis, TN, where they boarded a train bound for Richmond. Upon arrival at Richmond, the Adams Troop was joined by the Virginia Company (almost as splendid as the Adams Troop). On Oct. 24, 1861, Martin was promoted to Major and given command of this company commonly known as the “brag company of the South”. Maj. Martin and his men were baptized with fire at the Battle of Seven Pines and under Gen. J.E.B. Stewart, was incorporated into the famous Jeff Davis Legion. In the latter part of 1861 he was promoted to Lt. Colonel. The Jeff Davis Legion, as part of Stewart’s cavalry, saw extensive action at the Battle of Williamsburg, and many other skirmishes during May 1862,. On June 12-15, 1862, Stewart made his famous ride around McClellan’s army. Gen. Stewart hand-picked 1,200 men and officers to accompany him on this ride. They included the 9th VA Cav., Col. W.H.F. Lee, the 1st VA Cav. Col. Fitzhugh Lee and the Jeff Davis Legion, Lt. Col. W. T. Martin. The Legion fought in the Seven Days Battle and was with Lee’s Army when he forced McClellan’s Army off the peninsula and saved Richmond. On Sept. 17, 1862, the bloodiest day of the war was fought at Antietam. Lt. Col. Martin was personal aide to Gen. Robert E. Lee during this battle. The Legion attacked U.S. Gen. Abner Doubleday and his 30 guns capturing the cannons and their gunners. The Legion held the left flank supported by Gen. Early’s division. Due to his courage under fire and leadership ability, on Jan. 3, 1863, Martin was promoted to Brigadier General and transferred to the western front and given a cavalry division under Gen. “Fighting Joe” Wheeler as part of Bragg’s Army of the Tennessee. The Jeff Davis Legion went on to fight in many of the most famous battles of the Civil War, including: Brandy Station (June 9, 1863), Upperville (June 21, 1863), Gettysburg (July 1-3, 1863), Bristoe Campaign (Oct. 1863), Mine Run Campaign (Nov.-Dec. 1863), The Wilderness (May 5-6, 1864), Spotsylvania Court House (May 8-21, 1864), North Anna (May 23-26, 1864), Cold Harbor (June 1-3, 1864), Petersburg Siege (June 1864-April 1865), Williamsburg Road (Oct. 27, 1864) and the Carolinas Campaign (Feb.-Apr. 1865). This represents an opportunity to acquire an extremely historic pair of early Colt pistols that undoubtedly saw a tremendous amount of heroic service in the Civil War. Accompanied by the aforementioned Colt letter along with a 3-ring binder of the history of the Jeff Davis Legion of Mississippi Cavalry and their service throughout the Civil War. Gen. Martin, had a long & distinguished career after the Civil War in local & state politics, a railroad man and a trustee of a university, a college and a hospital and was eventually elected a state senator and served from 1882-1894. In 1905, at age 82, Gen. Martin was appointed Postmaster of Natchez and died on March 10, 1910, fifteen days before his 87th birthday. He was born March 25, 1823 in Glasgow, Kentucky. The revolvers both have 8” rnd bbls with full fluted cylinders and 4-screw frames cut for shoulder stock, with round headed hammer screws apparently having been changed out some time during period of use. Stock screws are also short & round headed apparently having been changed. They both have brass trigger guards & iron back straps with 1-pc walnut grips. CONDITION: Both revolvers are in nearly identical condition. No orig finish remains being a cleaned gray patina over all metal surfaces, beginning to repatinate. Both have minor dents & dings and apparently have been waxed. Both have chipped grips with No. 1542 slightly battered on bottom. Both grips show moderate to heavy wear and a fine hand worn patina. On both, mechanics are fine with strong bores and moderate to heavy pitting. A truly historic & wonderful pair of documented Civil War used Colts. 4-32670 JR612 (50,000-80,000)

RARE MARTIALLY MARKED COLT MODEL 1860 FLUTED ARMY PERCUSSION REVOLVER. SN 2698. Cal. 44. Rare 7-1/2″ rnd bbl fluted Army with New York address and German silver front sight. It has full fluted cylinder with patent date in one of flutes but unfortunately no visible serial number. It has 4-screw frame cut for shoulder stock with flat head hammer screw & short stock screws. It has brass trigger guard with iron backstrap & Army size 1-pc walnut grip that is from a later 60 Army. Grip has the number “7509” in backstrap channel and is carved on bottom left “H.B. JOHNSON.” Accompanied by a Colt factory letter identifying this revolver with 7-1/2″ bbl as having been shipped April 4, 1861 to the United States Quartermaster in New York in a shipment of 300 same type guns. CONDITION: Good, all matching except wedge which is numbered “5848” and appears to be from a Navy sized revolver, the cylinder which is unnumbered and grip as noted above. Bbl retains 30-40% blue turned brown in most sheltered areas. Cylinder retains an artificially aged patina in flutes, cleaned to gray on outer diameters with a few spots of scattered fine pitting. Back of cylinder has all six safety pins prominent. Frame retains faded case colors around screws with balance turned gray. Grip frame is a light brass patina & backstrap is a silver metal color. Wedge screw & a couple of frame screws are replacements. Grip, with legible cartouches, is sound showing moderate to heavy wear and retains 50-60% of its orig finish. Mechanics are fine, strong dark bore with fine pitting. 4-33349 JR362 (1,000-2,000)

SCARCE COLT MODEL 1860 FLUTED ARMY PERCUSSION REVOLVER. SN 1376. Cal. 44. Early fluted Army with 8″ round bbl, German silver front sight, full fluted 6-shot cylinder with patent date in one flute and serial number in another. It has “COLT’S PATENT” on left side of frame which has four screws & is cut for shoulder stock. It has a nickel plated brass trigger guard & nickel plated iron backstrap with 1-pc walnut grip. A large number of these early 60 Armies were shipped south and are generally considered Confederate used arms. CONDITION: Fine, all matching. No orig finish remains being a smooth dark chocolate brown patina overall, possibly artificial aging with some fine pitting near muzzle end of bbl. Hammer has fine pitting on sides. Trigger guard retains most of its strong orig nickel finish with a few spots of brass showing through. Backstrap retains 50-60% nickel finish with bright metal showing through. Grip is sound with light to moderate wear and retains most of its original varnish. Mechanics are fine, worn bore with fine pitting. 4-33340 JR345 (3,000-5,000)

CAPTURED CONFEDERATE USED REMINGTON ARMY REVOLVER WITH HOLSTER, CARTRIDGE BOX, AND BELT. SN 56280. Cal. 44. Grouping consists of Remington Army revolver, military-style flap holster – possibly Confederate, pistol box, and British-style belt with 2-pc brass buckle. Accompanying this grouping is a letter written in 1908 which states, “Confederate pistol taken from a Confederate LT. at the Battle of Piedmont, June 5, 1864. He was from Tenn. My father kept in the bank during his employment, 26 years. It is considered a good relic of the Civil War. I carried it until the close of the war . . .”. SN on cyl is 5950—does not match SN on gun; however,cyl is “K” marked indicating Army replacement this is not uncommon on U. S. martial pistols that were used in the Civil War. Left stock shows residual cartouche and a couple of carved initials. Remington’s bbl address is all discernible. Pistol was well-used but still operates mechanically. Belt loop on holster is torn. The piece of leather that would have held tab is missing. Half the stitching of holster is missing. Pistol box has one torn belt loop and one frayed belt loop. Some stitching is torn. Tab is missing. Patent leather English-style belt with decorative buckle is worn, but not as badly as holster and pistol box. CONDITION: Metal of pistol is gray/brown with scattered pitting, numerous small dings and dents. Small traces of finish on bbl in protected areas. Leather is well-worn, losing most of its black surface on holster and cartridge box, as described above. Belt is sound with stitching missing where belt attaches to brass sword hanger. 4-31486(2,000-3,000)

UNIQUE CONFEDERATE NASHVILLE MAKER MARKED HOLSTER. You are bidding on an extremely rare Confederate military holster maker marked “John Morrow & Son/ NASHVILLE, TENN”. John Morrow of Nashville, Tennessee made Confederate Leather accouterments, based on existing receipts from early 1862. The only other marked example we know of is an infantry cartridge box. There are probably no more than 10 Confederate maker marked holsters and any surviving Nashville holster is extremely rare since Nashville fell to Union forces so early in the war. This example is subtle with about half its orig black finish retained. The holster lacks the strap for closure and is missing about a 1″ pc at muzzle; an additional 2 sets of cuts have been made behind orig belt loop for better belt attachment as can be seen in photos. This is the only example known to us and we doubt there is another. This holster will fit most any Confederate primary revolver such as a Griswold, a Leech and Rigdon, Rigdon & Ansley or a Spiller & Burr. CONDITION: Leather is sound and intact. Black coating is crazed and flaking overall. About 50% of the orig black polish is present. Muzzle end is missing a 1″ square pc of leather as can be seen of photographs. As can be seen in photos, several letters and maker’s mark are not discernible. 4-32823 JS502 (4,000-6,000)

EXTREMELY RARE ATLANTA ARSENAL MADE HOLSTER. There are no more than 10 maker marked Confederate holsters known to us and this is only the 2nd from the Atlanta Arsenal we know of. This flap holster was made for a Colt Pocket pistol or similar sized gun. This holster is complete with belt loop and closure strap. The markings: ATLANTA ARSENAL/GA/1862” are excellent and easily read. This holster was for many years loaned and on display in The Atlanta Historical Society now the Atlanta History Center. A very rare Confederate marked accoutrement and probably the only marked Confederate holster for a pocket sized pistol known. CONDITION: Good overall with crazing, flaking and cracking and chipping. Holster is dry and flat from display. 4-32834 JS15 (5,000-7,000)

CONFEDERATE CSA BELT BUCKLE . Several varieties of CSA rectangular belt plates are encountered. This is what is known as a “Virginia” style; which is usually associated with the Army of Northern Virginia. The Virginia style is typically thinner than the Western or Georgia style buckles. The Virginia style also has larger periods. This plate measures correctly and is 48 mm high and 71 mm long. This buckle appears to be excavated and, though cleaned, it still exhibits a chocolate/brown patina. A casting flaw in the upper right hand corner produces two small holes as can be seen in the photographs. You are bidding on classic enlisted man’s belt buckle probably used in Virginia in the late campaigns of the Civil War. CONDITION: Good overall, as described above. 4-32836 JS390 (1,500-2,000)

VIRGINIA SABER BELT BUCKLE. 51 mm by 88 mm, this model 1850 saber belt buckle exhibits the state seal of Virginia showing Victory standing triumphantly over the tyrant. The motto “SIC SEMPER TYRANNUS” and “VIRGINIA” are found above and below a state seal. This excavated buckle has been cleaned but still exhibits a brown/green patina, with dirt still clinging in some areas. Buckle shows several bends and a crack in the border at top of buckle as can be seen in the photographs, however it does not hurt the aesthetics of this well detailed belt plate. A benchmark number 503 is seen on reverse near belt hook. CONDITION: Good, as excavated with bends as described above. 4-32837 JS351 (1,500-2,000)

UNKNOWN UNMARKED LARGE FRAME PERCUSSION REVOLVER SN NSN. Cal. About 44. Unusual revolver, probably Confederate, with 8-3/4” rnd bbl, dovetail brass blade front sight with grooved top strap rear sight. The bore has 7-groove rifling with right hand twist. It has a Le Mat style rammer attached to left side with a long thin handle with notch on inside and a raised half moon from side of bbl to secure rammer. It has a flat sided receiver similar to a Dance dragoon with bullet loading notch in left front side of frame. It also resembles Beaumont revolver imported into the southern United States in large quantities. Top strap is flat also. It has a small sized hammer with short knurled spur and a thick short trigger. Grip is 1-pc and long, resembling a Starr revolver. Cylinder pin is large & heavy with graduated rings at the end and is secured in frame with a rotating pin similar to Whitney’s percussion revolvers. The 6-shot cylinder is heavy with straight sides with deep nipple wells and star wheel similar to Remington’s style. It has safety notches in the lands between the nipples. It appears to be hand forged. Consignor states that this identical revolver appears on p. 203 of a book (title unknown) by Sellers & Smith and that it is the only known example. Consignor states that he purchased it from the Henry Stewart Collection. PROVENANCE: Henry Stewart Collection. A similar revolver is pictured in “American Percussion Revolvers” pg 203. CONDITION: Good. All metal retains a mottled medium plum/brown patina with a spot of heavy pitting on top of bbl and lighter pitting on frame. Grip is sound with a hand worn patina and some light battering on butt. Will not hold steady in full cock notch and does not appear to have a half cock notch, otherwise mechanics are fine, worn dark bore. 4-32680 JR498 (1,500-2,500)

UNMARKED UNKNOWN MAKER LARGE FRAME PERCUSSION REVOLVER SN 4340. Cal. About 45. Nickel finish with 7-1/2” oct bbl with dovetail target style front sight and a small fixed rear sight screwed to top strap. It has a Whitney-style 3-pc rammer with Whitney-style latch and a Whitney-style hammer locking screw. It has an iron frame with 1-pc grip frame with integral trigger guard and a most unusual coil hammer spring. It has a thick, flat-sided hammer with hand knurled short spur and it has 2-pc walnut grips. The heavy 6-shot cylinder has very long flutes with deep flared nipple recesses and Remington-style star wheel at rear end. Serial number appears on left side of frame, bottom of bbl & butt strap and the rammer handle & locking pin. Curiously it has “B” inspector initials on left side of frame, back of recoil shield and again on both sides of bbl lug and both sides of bbl. Cylinder also has the “B” marking. Bore has 5-groove rifling with right hand twist. Right side of bbl lug is stamped through nickel finish “45 / 35 / 210”. This is possibly the bullet size, powder charge & bullet weight. This is a most unusual & well made revolver that certainly had strong possibilities. CONDITION: Fine. Overall retains about 70% strong orig nickel turned milky with exposed metal a dark patina. Grips retain orig finish around top edges with minor nicks & scratches and have a hand worn patina. Hammer is not solid in safety notch, otherwise mechanics are crisp with a very bright shiny bore. 4-32677 JR500 (1,500-2,500)

UNKNOWN UNMARKED NAVY SIZE FRAME PERCUSSION REVOLVER SN NSN. Cal. About 46. Well made percussion revolver with 8-1/8 medium weight oct bbl, with 4-groove rifling, having a Colt-style 2-pc rammer with horizontal Navy style latch & stud. Sights have been broken away. Rammer handle is octagonal in shape. It has a thick Colt-style bbl lug with Colt-style forcing cone extension. It has a 5-shot cylinder with a rounded blade style cylinder stop slots with integral star wheel on back edge, no safety pins and deep, wide nipple recesses. Frame is flat sided with narrow recoil shields and a shallow capping groove on right side. There is no bullet loading notch in bbl lug. Hammer has a high spur with a sharp curl. Trigger guard appears to be integral with plate having a thick, square back edge. Grip frame attaches similar to a Colt with 2-pc walnut grips and a rounded buttstrap with flared front & back edges. Hammer spring is a long complicated “U” shape and hammer has a roller for the spring. Inside of grips are milled to accommodate spring. CONDITION: Very good to fine. Bbl & rammer retain a blue/brown patina mixed with orig blue in sheltered areas and fine surface rust. Cylinder is a blue/gray patina with light surface rust and one area with numerous small nicks. Frame & grip frame also retain a blue/brown patina with stronger blue on frame in sheltered areas. It also has light surface rust and some nicks on left side of frame. Grips are sound with a few dings on left side and retain a hand worn patina. Hammer will not hold firm in full or half cock notches, otherwise mechanics are fine, worn dark bore. 4-32676 JR499 (1,000-2,000)

CONFEDERATE D-GUARD BOWIE WITH TIN SCABBARD. This massive clip-point Bowie exhibits a 13” clip point blade that is over 1/4” thick at ricasso. Blade at its widest is almost 2”. Iron D-guard surrounds a shaped wood handle. Well-made tin scabbard still retains its orig tin belt loop. Indiscernible writing occurs on reverse of scabbard. CONDITION: Blade is brown/gray with several. nicks in cutting edge and sharpening. Wood grip has two 5” longitudinal glued repairs. 8-76217 JS221 (6,000-8,000)

RARE CONFEDERATE D-GUARD BOWIE “CUTLASS VARIATION”. Made by Louis Froelich at the Confederate States Arsenal in Kenansville, North Carolina. Termed a “Variation” because the guard does not flair like the standard Cutlass spear point blade with median ridge. Overall length is 21″. The blade is 16″ in length, 1-7/8″ wide & 5/16″ thick and has a diamond cross section. The D-guard is cut from 1/8″ stock and is 1-1/16″ wide. The guard does not flair into an oval but is the same width as it passes the blade and then forms a pointed quillion. This grip is the 1-pc turned walnut style: another style of grip with the walnut slabs held by iron pins is seen on Cutlass variations as well. There are fewer than 10 known examples of these variations and less than four known with this 1-pc grip. CONDITION: Overall very good with gray blade and guard with scattered pitting, grip is very good. 4-32669(5,000-8,000)

CONFEDERATE D-GUARD BOWIE. This massive Confederate Bowie, over 20” long with 15-3/4” clip point blade, is 2-1/4” wide and 1/4” thick. Maple grips are retained by 2 pewter pins. D-guard is made of brass and terminates into a large pewter ferule. This extremely well-made Bowie could easily have been made by a Kentucky rifle maker based on its quality and the finish of the tiger stripe maple grips. This knife was once in the collection of Norm Flayderman and is pictured in his book on American Bowie knives on p. 231. If you wanted to buy 1 great Confederate D-guard Bowie, this could be the one for you. CONDITION: : Blade is gray/bright with scattered areas of staining. Maple grips are scuffed and scratched, but still retain most of their orig varnish. Brass stirrup-shaped D-guard hilt is bent and has hairline crack which does not affect aesthetics. 8-76218 JS222 (6,000-8,000)

UNUSUAL HAND MADE, POSSIBLY CONFEDERATE, LARGE BOWIE KNIFE. Large old Bowie, handmade, probably from an old saw blade, with 17″ clip point blade, 22-3/8″ overall. Blade is 2″ at widest point and 1/8″ thick. It has a thin sheet brass handguard with crude brass ferrule and a smooth oak handle with oval brass cap that has tang pulled through and peened over. Accompanied by its orig black leather, wood lined sheath with brass tip and throat that has an elliptical stud with frog and long-drop belt loop. Sheath has a sewn seam on back side. This knife has all appearance of a country blacksmith made knife that likely was carried by a Confederate soldier in Civil War. CONDITION: Fair to good. Mostly a gray metal color with some light surface spotting & fine pitting. Edge has several nicks. Handguard is bent at top and handle is fine. Sheath is sound with an old heavily tarred surface that is heavily crackled. Brass has a dark patina. 4-32720 JR435 (1,250-1,750)

CONFEDERATE BOWIE BAYONET. Clip-point blade is 12” with rosewood grips with 2 crudely cut holes that could potentially have fit on a stick. I doubt these could have gone on a gun. Norm Flayderman pictures these in his book on American Bowie knives on p. 215. There is new, credible evidence that these knives may have been made by Rees Fitzpatrick of Nachez, Miss. Rees Fitzpatrick, prior to the war, made fine rifles. It is known he did deliver knives to the Confederacy. Accompanied by correct leather scabbard with brass mounts with riveted and sewn belt loop. CONDITION: Blade is gray/bright with scattered areas of staining and pitting. Rosewood grips exhibit most of its orig varnish with scattered dings, dents, and scratches. Brass scabbard throat and knife mounts are well patinated with scattered scratches. Brass drag appears replaced. Leather scabbard body is solid. Retains about 50% of its orig black surface. Throat is missing 1 of four pins. Stitching is missing from base of belt loop, otherwise it is intact. 8-76219 JS218 (4,000-6,000)

Revised: 10/19/2007

(Additional Information) We have recently been contacted by a Civil War scholar who provided us further information on the 29th Virginia. Subsequent research bears out what he has told us. The 29th VA was indeed attached to Pickett’s Division, however, prior to Gettysburg it, together with some of the other units, were left to defend Richmond. It is therefore unlikely that A.C. Clark, of the 29th VA, was present at Pickett’s Charge, but the knife is a superb example of an extremely rare, Confederate, handmade, inscribed fighting knife, with direct and conclusive information of ownership indicating Confederate use at both Richmond and during the Wilderness Campaign, nonetheless.

HISTORIC INSCRIBED CONFEDERATE SIDE KNIFE IN ORIGINAL SCABBARD USED IN PICKETT’S CHARGE. 9-3/4” double-sided blade made from file, is nicely etched “H. C. Clark Wythe City, Virginia Aug 16, 1861”. Henry C. Clark from Wythe City, VA, entered Confederate service July 23, 1861. He received this knife a month later, based on the inscription. Henry Clark served for the 29th Virginia, at Gettysburg with Pickett’s Division. He took part in the infamous charge on the 3rd, and last, day of Gettysburg, certainly one of the most famous charges in history. On July 3, 1863 Gen. Lee commanded Gen. Pickett to send his entire division against the center of the Union line. Approximately 12,500 Confederate soldiers did. Pickett’s Division alone suffered 2,655 casualties and the Confederate forces a 50% casualty rate. The charge and its failure was the beginning of the end for the Confederacy and is referred to as the High Water Mark for the Confederacy. Clark survived Pickett’s charge only to be captured in May 1864 during the Wilderness Campaign, and taken prisoner. He died at Elmira Prison on September 30, 1864, and is buried at the national cemetery at Elmira. Knife exhibits a 2-1/2” pewter crossguard, wood grip with iron buttcap. Scabbard is back sewn, decorated, brown leather with tin throat and drag. Integral sewn belt loop is still attached and sound. CONDITION: Blade is gray/bright with scattered staining and pitting. Octagonally carved wood grip is sound with scattered scrapes and scratches. Crossguard is very good, as is iron pommel, which is slightly loose with scrapes and scratches. Scabbard is very good overall, being very sound. Decorations on obverse are well-defined. Tin throat and drag have areas of rust. Stitching is complete with no reductions. An outstanding example in wonderful, as found condition with a remarkable history. 8-76221 JS223 (10,000-30,000)

LEECH & RIGDON CLIPPOINT BOWIE KNIFE. 8-1/4” clip point blade is mounted in a distinctive 5” Leech & Rigdon crossguard with Leech & Rigdon feathered short sword grip. This exact pattern of Leech & Rigdon we have not seen before. Most often, this style hilt is found with double-edged short sword blade, but this knife was obviously made as a Bowie. Note the bird’s head-shaped pommel, instead of it being round on both sides. CONDITION: : Blade is gray with scattered pitting, and staining. Brass hilt and crossguard show numerous scratches, dents, and old tool marks. The number “62” is crudely cut into top of guard adjacent to a Roman numeral “V”. 8-76222 JS220 (5,000-7,000)

RICHMOND SHARPS. SN 4725. Cal. 52. SN is found on bbl, lock, frame, and carbine bar. “Richmond VA” is discernible on bbl behind rear sight. Forestock has several glued repairs and exhibits an iron ferule where Richmonds normally have brass. Bbl band is cleaned and artificially aged and is possibly a reproduction. Buttstock fits gun poorly and has numerous nicks, gouges, and scrapes. Series of 12 notches is carved in comb (poss confirmed kills?). Buttplate is a correct Richmond Sharps buttplate; however, it appears excavated and cleaned. Lever tension spring is replaced. Gas seal on orig Confederate breechblock is loose. Lower tang assembly fits buttstock well and is probably from a U. S. Sharps, as is buttstock. A genuine Confederate Sharps with well-marked metal parts and, as with most Confederate arms, shows significant use. CONDITION: Tang is broken at back screw. Good overall. 4-32762(4,000-7,000)

POSSIBLE CONFEDERATE USED ENFIELD PATTERN 1853 RIFLE MUSKET SN NSN. Cal. 58. Short pattern Enfield with 33” rnd bbl, sq base front sight/baynet lug with saber bayonet lug on right side of muzzle. It has 1,000 yard ski jump ladder rear sight and engraved on top “B. COGSWELL. 224. STRAND. LONDON”. Maker’s name also appears on lockplate. It is mounted in one pc walnut stock with two bbl bands and a brass tipped ramrod. It has sling swivels on front band and tip of bottom tang and has a musket buttplate. Left side panel is stamped, upside down, “NT5”. Left side of butt is crudely carved “JF / Ft DONELSON”. Ft. Donelson was a Confederate stronghold about 30 miles west of Clarksville, TN which then is about 80 miles north and west of Nashville, TN. It is widely known that the Confederates purchased as many of these Enfield rifle muskets as their agents could procure and were used extensively throughout the war. CONDITION: Good. No original finish remains on the metal, being a very dark attic patina with some burnout in front of the nipple. Stock has a very old, period of use, chunk missing from the toe and a saw cut, just in front of the comb and retains 30-40% original finish, mostly on the forestock with the buttstock being a very dark patina. Front trigger guard screw is missing. Mechanics are fine, very worn, dark scaly bore. 4-59696 JR530 (1,000-2,000)

SCARCE 2-BAND “M” ENFIELD RIFLE. Cal. 58. NSN. Rare maker with 34-1/2” rnd bbl, square base front sight/bayonet lug with a saber bayonet attachment on right side of muzzle. It has “ETL” script inspector initials on upper left side of bbl, opposite nipple. It has two bands with long distance ladder rear sight. Lockplate has a spread-winged eagle perched on an American type shield with an “M” at top behind hammer with center of lockplate dated “1861”. Mounted in a 1-pc walnut stock with brass furniture and has sling swivels. Left side panel is stamped “17” and there is a “60” stamped in front edge of trigger guard tang. Right side of butt, just above sling swivel, has a deep cut, probably an old sword cut. Right side of butt also has a series of small dents. According to Flayderman’s Guide to Antique American Firearms, only a few thousand rifled muskets were estimated to have been made in period 1861-63. He states that they were made by J.P. Moore’s Sons from some Colt’s parts and imported parts. He lists them with 39” bbls and three bands with lock markings of ”1862”, “1863” or “1864”. It has been argued that these rifles & rifled muskets were Confederate issued but, according to Flayderman’s, a letter from J.P. Moore dated Jan. 13, 1862 refutes this stating that “the musket was theirs”. Conversely on pp. 98-109 of Confederate Longarms and Pistols A Pictorial Study, Hill & Anthony, a convincing argument that these rifles were, in fact, Confederate made rifle muskets using British parts for the most part. The 2-band examples are scarce with only 8 or 10 known. CONDITION: Fine. Iron overall retains a very dark attic patina with heavy pitting around nipple area. Lockplate & hammer retain a smooth even patina. Stock is sound with nicks & dings and retains a fine hand worn patina. Mechanics are fine. 4-32827(5,000-8,000)

CONFEDERATE USED AS FOUND HARPER’S FERRY CONVERSION MUSKET, CANTEEN, CARTRIDGE BOX AND BAYONET SCABBARD. An attached tag dated 1983 reads: “Musket, canteen, etc. were purchased in Perry County Pennsylvania. They came from descendants of Thomas Brooke who deserted the Confederate forces at Sterritts Gap, Pennsylvania. Brooke married a Perry County woman and lived the remainder of his life in the Keystone State”. This is an interesting grouping in as found “attic” condition. The homespun canteen sling is looped through bayonet scabbard and Cartridge box and is stapled to forestock of an early model Harpers Ferry musket dated 1816 which has been converted to percussion in the military style, probably in Virginia near the outbreak of the war. Musket bbl is 40-1/2″ long, stock is weathered and worn with Thomas Brooke’s initials carved in the right butt stock. The homespun cotton sling is typical of other sling material associated with the Confederacy. The bayonet scabbard is unusual and has many Confederate characteristics, it is totally hand sewn with a hand sewn tip. The cartridge box is typical of early war cartridge boxes with tart surface. This box like so many Confederate used and made boxes utilizes only a sling and no belt loops. This is a great historical group which will display nicely. Ex. Michael Kramer collection. CONDITION: Canteen is dented with scattered rust and pitting. Bayonet scabbard is good overall and sound with wear and scuffing to surfaces, stitching is fairly solid. Cartridge box is good overall, one roller buckle is detached and attached through sling, tin liners are still present. The staple, attaching sling, is not of a modern variety, sling appears mostly complete with a wire repair for attachment. Gun overall is good with metal surfaces exhibiting rust and pitting, stock surfaces are scuffed and weathered as can be seen in photographs. 4-32672(5,000-7,500)

SUPERB PRESENTATION STAFF OFFICER’S SWORD OF CIVIL WAR MEDAL OF HONOR WINNER LIEUTENANT COLONEL JACOB FRICK. A marvelous opportunity to own an incredibly important sword inscribed to an American hero and Medal of Honor winner. This Horstmann staff officer’s sword with 32-1/2” blade is of the highest grade for this manufacturer. Blade is brightly etched with military motifs and maker’s mark. Grip is made of sheet silver, finely decorated with and engraved foliate design. Hilt and scabbard mounts are extra-rich, having more raised relief design than normally seen. Each scabbard mount has a 1-1/2” silver oval plaque with patriotic motif. Presentation plaque between top mounts reads “Presented to Lieut. Col. J. G. Frick, 96th Regt. P. V. by his friends in the regiment for his gallant conduct at Gains Hill, June 27th and his efficiency as an officer. July, 1862”. This wonderful sword has never had ownership outside of Lt. Colonel Frick’s descendants and has never before been offered for sale, having recently been discovered in a descendant’s home. Of even more importance is the historic and indelible impression that Col. Frick made on the history of the Battles of Fredericksburg and Chancellorsville by his incredible valor and leadership under enemy fire. This impression was so recognized by the Congress of the United States by awarding him the Medal of Honor in 1892 for his valiant deeds. Born on January 25, 1825, in Northumberland County, PA, Jacob G. Frick entered military service as a 3rd Lt of the 3rd Ohio Infantry on June 6, 1846. He served throughout the Mexican War and was commissioned 2nd Lt, 11th U. S. Infantry, upon expiration of his term. In the opening days of the Civil War, Frick was recruited as Lt Col. of the National Light Infantry of Pottsville (PA), later designated as the 96th Regiment Pennsylvania Infantry. He mustered in on September 23, 1861. In July 1862 he was appointed Colonel of the 129th Regiment Pennsylvania Infantry. During his service as Colonel of the 129th the regiment participated in the Battles of Centreville, Antietam, Fredericksburg, and Chancellorsville. Frick returned to Pottsville for scarcely a month when Pennsylvania Governor Curtin asked him to raise a militia regiment to help repel Lee’s invasion of Pennsylvania. Frick became Colonel of the 27th Pennsylvania Emergency Militia on June 22, 1863. During their service they fought at Wrightsville and Columbia. Jacob Frick returned once again to Pottsville and resumed his successful screen manufacturing business. He died on March 5, 1902 and is buried in plot# 346 in the Presbyterian Cemetery, Pottsville, Pennsylvania. Frick’s Gallantry: Two heroic acts were cited by the United States Congress in their decision to award Frick the Congressional Medal of Honor. During the Battle of Fredericksburg, Frick led the left flank of the Union forces poised against Marye’s Heights. General Hooker personally requested that Frick lead the charge against the Confederate held position with the 129th Pennsylvania Infantry. Leading his troops to position in front of the stone wall, the enemy poured merciless fire upon them. During their advance a shell struck a horse at Frick’s side literally covering him with its flesh and blood, at the critical point of the charge Frick’s color bearer was shot down but Frick seized the colors himself and took the lead. Shortly after Frick’s recovery of the colors, the flagstaff was shot from his hands and the colors draped upon his shoulder. In this state, struggling to keep the colors aloft, he continued his advance upon the stone wall. In the futile attempt, Frick lost 148 of his 500 men; shell fragments in the thigh and right ear wounded him. During the Battle of Chancellorsville Colonel Frick and the 129th Pennsylvania occupied an advanced position in the area of the heaviest conflict. He held the position against superior numbers long after the troops on his right and left had retired. The topography prevented him from knowing that the Confederates had already passed his right flank and were gaining on the rear of his column. He retired the 129th in good order to the rear of the batteries that were able to move into an advanced position because of the steady fire of his troops holding the enemy in check. As soon as he took up the rear position, the Confederates came upon him capturing the regimental colors and taking prisoners, including his Lieutenant Colonel. Colonel Frick quickly rallied his men and, in hand to hand combat, recaptured his comrades and the regimental colors bringing to the rear as prisoners the very Confederates who had accomplished the dash against them. From the early date of this presentation, Col. Frick would have had this sword during the Battles of Fredericksburg and Chancellorsville, where the actions occurred that led to the awarding of the Medal of Honor CONDITION: Blade is bright with most orig frosting remaining on blade. Hilt and mounts retain 80%+ orig gilt. Scabbard body retains most of its orig brown finish. 4-32912 JS225 (15,000-20,000)

PRESENTATION CANE OF CIVIL WAR MEDAL OF HONOR WINNER LIEUTENANT COLONEL JACOB FRICK. This wonderful relic is one of the most important artifacts from the Battle of Fredericksburg and the Union Army’s ill-fated charge up Marye’s Heights against the Army of Northern Virginia. This remarkable cane was fashioned from the flag staff shot from Lt. Col. Frick’s hands while leading his regiment against the Confederate forces positioned on Marye’s Heights, Fredericksburg, VA, December 13, 1862. This cane has never had ownership outside of direct descendants of Lt. Col. Frick and has never before been offered for sale, having recently been discovered along with his sword in home of descendants. The 3-1/4” silver cane top has is wonderfully hand engraved with a presentation which reads “To Col. J. G. Frick, 129th Regt. Pa. Vols. Part of flag staff shot off in his hands while leading his regiment in the final charge on the Rebel Works at the Battle of Fredericksburg, Va. Dec. 13th 1862”. As noted in the description of the sword before, Lt. Col. Frick’s regimental color bearer was shot down while advancing on Marye’s Heights. Frick personally recovered the colors, subsequently having the flag staff shot from his hands and the colors draped upon his shoulder. In this state, struggling to keep the colors aloft, he continued his advance on the stone wall. In this futile attempt, Frick lost 148 of his men, and he was also wounded by shell fragments. This may be the most historic cane we have ever offered and represents one of the most important relics from the Fredericksburg campaign CONDITION: Overall cane is in very good condition. Tip shows little wear. Cane body retains much of its orig lacquer. Decorated silver tip has several small dents, scattered scratches and is loose. 4-32913 JS226 (3,000-5,000)

PRESENTATION SWORD OF GENERAL JOSEPH CARR. This is a most unusual pattern, being European, probably French-made for the American market, with a cruciform guard in shape of 6” spread-winged eagle. 30-1/2” dbl edged blade with central fuller is etched with military motifs, including crossed flags and American eagle. Pommel is of knight’s head with fully sculptured eagle on top. Sharkskin grip has fancy, triple-branched wire. Scabbard mounts are decorated in raised relief with top two mounts having identical sprays of military arms. Drag is decorated with foliate design. Ring mounts have a most unusual feature of human hands holding the hanging rings. Crossguard has presentation “To Gen. Joseph B. Carr from his friends Sept. 7, 62”. Sword is illustrated in American Swords and Sword Makers, Vol. 2 by Richard H. Bezdek. Brig. Gen. Carr originally entered the service May 1861 as Col. of the 2nd NY Volunteers. He commanded this unit at early engagements of the War, including Bethel, Fair Oaks. He commanded the 2nd New Jersey Brigade at Malvern Hill and distinguished himself at that battle. On Sept. 7, 1862, he was commissioned Brig. General for gallant and meritorious services in the field. Coincidentally, the date of this presentation corresponds to the date of his field promotion. He later served at many other major battles in the Eastern Theatre, including 2nd Bull Run, Chantilly, Chancellorsville, Fredericksburg, Gettysburg, and the Richmond Campaign and Petersburg. At war’s end, he was brevetted Major General. He left the service Oct. 1865. After the war, Carr served in various administrative posts in the state of New York, including being Secretary of State for three terms. He also ran for Governor of New York in 1885. CONDITION: Blade is gray/bright with areas of black staining. 18” etched panels are all discernible, though weak in areas from cleaning. Sharkskin grip is very good with wear and flaking to high spots. Copper wire wrap is complete. Brass scabbard, scabbard mounts, hilt, and pommel are very good with traces of gilt remaining in protected areas. Chain connecting pommel to crossguards is replaced. 4-31586 JS231 (12,000-15,000)

SPECTACULAR HIGH-GRADE PRESENTATION SWORD OF GEN. CHARLES LABUZAN OF THE ORLEANS GRENNDIERS, LOUISIANA. Sword is of the highest quality made by the preeminent American sword maker of its time, N. P. Ames, of Springfield, Massachusetts. Hilt and mounts are sterling or coin silver. American swords made of precious metal are rare and desirable and generally reserved for state and congressional presentations. Grip is ebony wood with inset silver and mother-of-pearl. The use of inset ebony is rare in Ames swords; one well-known example is the Kentucky Giant’s sword of James Porter pictured in Hamilton’s Ames book. The sword exhibits numerous unique features of the highest quality and design. This was a custom designed sword and there is nothing else like it ever made. This is indeed the only Ames sword known with a true colichemarde blade. Colichemarde blades originated in 18th century France, and were thought to be the best blades of their day. (See Peterson, American Swords). Cruciform guard is decorated with seashells terminating upward into a flaming bomb. The top of the guard is engraved “Orleans Grenadiers”. Presentation languet shield is surrounded by flags, weapons, and stars with a large spread wing eagle above the shield which reads “Presented to Captain C. A. Labuzan by the members of the Orleans Grenadiers, January 24, 1841”. The pommel is Knights head with highly detailed foliate decoration. Top of pommel is engraved “Capt. Labuzan”. Blade is colichemarde and finely engraved. Triangular colichemarde blades are rare in American swords and since they originated in France and New Orleans had so much French influence; the Orleans Grenadiers must have specifically asked for this French inspired blade. Blade is decorated with flaming bombs, patriotic shields, sprays of arms, and Indian with Tomahawk raised, eagle surmounted with stars and “liberty”, and an eagle holding a ribbon, which reads “Grenadiers d’Orleans”. Scabbard is form-fitted, brass-covered with leather, which is flaking and partially missing. This leather can be restored easily and aesthetically. The long silver drag is finely engraved with foliate decoration terminating in a “flaming bomb.” Throat is finely engraved with a frog button decorated with two flags and a liberty cap. Throat is also engraved “Capt. C. A. Labuzan, O.G.”. General Charles Labuzan’s obituary appears in the first column of the front page of the New Orleans Picayune on June 30, 1869: “Gen’l Labuzan reached quite a ripe age during the whole of his life . . . he served in the Mexican war . . . began prominently connected with the volunteer military companies of the city and was captain of that favorite one, the Continental Guards, and in the organization of state troops in 1861, became Brigadier General under Governor Moore.” On the front page of the New Orleans Picayune (Jan 26, 1841) the story of the presentation of the sword appears . . . “Urbain Plauche, a veteran of 14-15, one of the remaining heroes of our glorious eighth of January, and the oldest of the Grenadiers was selected to present the sword”. Labuzan in his acceptance speech “ . . . so long as I am associated with the Orleans Grenadiers in any capacity whatsoever, it shall be my highest pride, as well as my cherished delight, to make any improvement in their ranks, to enhance their reputation as men, and their glory as soldiers.” The paper further states “the sword is of exquisite workmanship, “very dear to fancy, very responsive to the hilt, of more delicate carriage and very liberal conceit” it was made in Springfield, Mass by N. P. Ames, and he is every way worthy to be looked upon with pride as a specimen of native manufacturer. The blade is “of the ice-brook’s temper”. The hilt is of inlaid ebony, held in chased and engraved ornamental work of solid silver . . . a more tasty and elegant affair would hardly be conceived. We venture to say no enemy of America will ever wish to die by more beautiful weapon, or by a braver hand than the one in which it has been placed.” CONDITION: Blade is gray/bright with scattered black staining, however, etched panels are all distinct and discernable. About a two-inch piece of silver wire is missing from obverse sword handle. Silver mounts and hilt exhibit black oxidation in recessed areas. High areas appear polished. Brass scabbard body is missing about 50% of its orig white leather covering. 8-76159 JJ23 (50,000-80,000)

CONFEDERATE CAVALRY SABER. This cavalry saber, probably made by Louis Haiman of Columbus, Georgia, is in as-found condition with fine, untouched patina throughout. This is one of the most classical encountered of all Confederate sword with all the typical C.S. features, but you would be hard pressed to find a better, untouched sword than this. CONDITION: 35-1/4” blade is brown with scattered staining and pitting. Brass hilt and pommel have rich patina with areas of black staining. Wood grip exhibits all its orig wire, though wood has several longitudinal cracks and is missing all its orig leather covering. 4-31539 JS215 (2,250-3,250)

U.S. CIVIL WAR FOOT OFFICER”S SWORD WITH “CSA” and “FIVE FORKS” ON SCABBARD. This sword is a standard model 1850 Foot Officer’s Saber agent marked Schuyler, Hartley and Graham, New York. Blade has typical American patriotic motifs. The hilt is typically florally decorated. The scabbard mounts are engraved including a patriotic eagle on the drag. What makes this sword so unusual is the soldier scratched on design of CSA in a medallion on a pedestal above the words “Five Forks”. If only this sword could talk, what stories could it tell – was it captured at Five Forks by a Confederate soldier? Was this sword taken from the body of an Union officer found dead on the battlefield? The Battle of Five Forks was fought on April 1, 1865, southwest of Petersburg, Virginia, in Dinwiddie County, during the Appomattox Campaign of the American Civil War. The battle, sometimes referred to as the ” Waterloo of the Confederacy,” pitted Union Major General Philip H. Sheridan against Confederate Major General George E. Pickett of Robert E. Lee’s Army of Northern Virginia. Pickett’s loss at Five Forks triggered Lee’s decision to abandon his entrenchments around Petersburg and begin the retreat that led to his surrender at Appomattox Court House on April 9. CONDITION: Overall very good. Blade is gray/bright was scattered pitting and staining. Etching is very good. Leather grip is about 90% intact and the wire wrap is complete. Scabbard overall is good as cleaned. 4-32953 JS501 (2,500-3,500)

MODEL 1840 AMES FOOT INFANTRY OFFICER’S SWORD . This is the Regulation American Sword for Company grade Officers of Infantry from 1840 ’til 1850. This is the regulation pattern sword for infantry officer’s used in the Mexican war. This is a very nice example with 31-3/4″ straight blade etched with maker’s mark “N.P. Ames/Cutler/Springfield” and various patriotic motifs. The hilt is gilded brass with a decorated urn shaped pommel. The reverse counter guard is hinged. The scabbard his black leather with gilded brass throat and drag. The throat has a hook stud for frog with an unusual Maple leaf decoration pinned and frog button. This is a scarce American sword with an unusual Maple leaf device that could have been carried by a Vermont officer. CONDITION: Blade overall is gray/bright with all etching discernible. Silver-plated copper grip is worn with several small dents. Gilding to hilt is 80% plus, gilding to drag is 80% plus, gilding to throat is only visible in traces. Scabbard body is solid with most all orig. Black coating contact has some cracking and stuffing. Maple leaf device is loose and turns on its pin. 4-32826(3,500-4,000)

UNIUQE SILVER HILTED PENNSYLVANIA LIGHT DRAGON OFICER’S SABRE, WAR OF 1812 This rare and unique horseman saber has 35-1/2” blade inscribed “Pensilvania Light Dragoons” and has a motto “for my country” in ribbon below arm below arm wielding a sword. This is a unique description. The silver hilt has five branched and is touchmarked “WMB” which is thought to be Wm. Mannerback of Lancaster, PA. This is the only known sword by this Silversmith. It is also the only officer’s sabre known of the Penn. Lt. Dragoons, the enlisted pattern is also rare. The grip of this sword I s made of wood covered with whale BALEEN! This is the only American sword known with a BALEEN wrap. CONDITION: Blade is gray with staining and pitting. Etched panels retain traces of gold and are discernible. Silver hilt is good and touchmark is discernible on quillon and knucklebow. Baleen wrap is mostly intact with the some reductions and warping. 4-31613 JSHW6 (12,000-15,000)

RARE HUTTON, ALBANY, NY HORSEMAN SABRE: REVOLUTIONARY WAR AND WAR OF 1812 ERA This unique sword once in the collection of William Guthman started out life as a classic Rev. War “smooth headed lion”: pommel sword. Hutton, with his unique blade of “jousting knights”: has updated and rebuilt this sabre for War of 1812 use. The grip has been lengthened and a backstrap braized onto pommel. A Hutton sword and dirk sold in Dec, 2006 for $75,000 and a Hutton silver hilt sold in 2000 for $27,000. Both these signed swords have these nearly identical massive 36” blades with “jousting knights” decoration. CONDITION: Blade is very good with scattered staining and putting. Hilt blade decoration is mostly intact. Hilt has broken branch. Grip leather is intact but crazed and flaking. Hilt and pommel are smooth with patination. 4-31536 JSHW3 (5,000-7,000)

UNIQUE AMERICAN SILVER HILTED HORSEMAN OFFICER’S SABRE CIRCA 1805. This saber was most likely made in Philadelphia by a silversmith and sword maker who was well aware of Napoleonic 1st Empire officer’s swords. It is amazing a sword of this design and quality was not signed. The massive 31” long, 1-3/4” wide blade is in very good condition being gray with lots of original polish with only light staining and putting. The massive carved ivory grip is very good with minor age cracks and scattered scratches. The silver stirrup shaped guard is decorated with raised relief spray of arms and flags. The “horse hoof” pommel exhibits 1-1/2” oval drooped wing American eagle looking right and languet exhibits a 1-1/2” oval with American eagle looking left. The quillon is also an eagle head. Hilt overall is in good condition. The pommel has silver repair to pin where stirrup enters. The pommel also exhibits fine etched decoration along its edges. The silver mounted scabbard has similar decoration on throat. Scabbard lacks drag but scabbard is sewn to bottom and has tooled border decoration and may never have been fitted for one. Scabbard body is sound and pliable with crazing and loss of much original surface but is still complete and fits well. This sword was once a centerpiece of Bill Guthman’s American Silverhilt collection. CONDITION: As described above. 4-31535 JSHW2 (12,000-15,000)

AMERICAN REVOLUTIONARY WAR “SMOOTH HEADED LION” HORSEMAN SABRE Classic Rev. War 3 fullered blade with smooth headed lion pommel with a partial scabbard. Scalloped, slotted guard is missing chain that once attached to pommel. Classic, well defined “smooth headed” American lion head pommel was cast in 2 pieces. Scabbard is broken but retains brass throat with frog button. CONDITION: 33-1/2” blade is gray with staining and pitting. Brass cross guard and pommel are smooth and patinated. Wood grip is good. Scabbard body is sound retaining most of its original black surface. 4-31537 JSHW4 (6,000-8,000)

REVOLUTIONARY WAR “GARGOYLE” HEAD HANGER. These English made swords generally predate the American Revolution: circa 1745-1765 according to George Neuman in his book “Battle Weapons of the American Revolution”. This sword with about a 24” blade is American in style with running wolf motif and date “1776”. You couldn’t have a better date on a Rev. War sword. This sword retains its original tooled leather scabbard with brass mounts. CONDITION: Blade is gray with scattered pitting markings on blade and very good. Hilt and scabbard mounts are brass and cleaned. Scabbard mottled with good surface and tooled design. 4-31534 JSHW1 (3,000-5,000)

THE FINEST KNOWN IDENTIFIED COOPER IRON WORKS CONFEDERATE D-GUARD BOWIE KNIFE AND SCABBARD IN EXISTENCE. An extreme rarity is this fine Cooper Iron Works fighting knife identified to Sargent William Mims one of 5 identified and recorded Civil War Confederate D-Guard Bowie knives made by the Cooper Iron Works of Cartersville, Georgia nearby the Etowah River (and often called the “Etowah Iron Works). A massive clipped point knife with a sheet brass D-guard, turned black-stained wooden handle with brass ferrules in a brass mounted black bridle leather scabbard. Presentation names on the other 4 known knives are Seago, Clark, Haynes and Bell. The names are all stamped with individual die, all being the same size and style. Mims” name is correctly stamped as these others on the D-guard. The overall length of the Mims knife is 18” with a massive clipped point blade 1-3/4” wide and 11-5/8” long. The scabbard is of black bridle leather stitched at the sides with a single belt loop on the reverse, sewn at the bottom and attached with two copper rivets at the top. The throat is decorated with a sheet brass band having a small decorative languet. The tip is covered with a pointed sheet brass drag secured with 4 pins. The front side of the scabbard is boldly stamped with the initials “G.C.G.”. G.C.G. denotes the Gate City Guards, among the most elite of Atlanta militia units formed prior to the Civil War. The Gate City Guards have provided troops for all American wars since the Civil War serving with distinction. Approximately 100 of these knives were thought to have been made by Cooper in fulfillment of his promise to arm the Atlanta Greys and the Floyd Infantry-the two units in which his sons would serve the Confederacy. Only 5 of the 100 are known, the named specimens are thought to have been presented to officers from several Georgia units by Cooper himself. An extensive amount of research has been completed on the Cooper Iron Works, the life of Mark Anthony Cooper as well as tracing the names of the known presentation Bowie knives. An extensive file accompanies the knife. “Sargent and later Major Mims” is listed in the Index to the City of Atlanta for this period. Accompanied by an extensive research file and book. This is no doubt the finest untouched and historical Confederate D-guard to ever be offered privately or in auction. CONDITION: Excellent. Certainly the finest known example of its type. The blade is bright and appears to have never been cleaned. The brass has a light patina worn on the high spots from handling. There is slight wear to the black stain on the turned grip and the scabbard is strong, not flaking and without any major bends or flaws. Most certainly an historic knife and an important find. These Cooper fighting knives are among the most desirable Confederate weapons. One of 5 presentation examples known. 4-31236 CW5 (55,000-75,000)

OUTSTANDING WOODHEAD & HARTLEY EARLY BOWIE KNIFE. Fine English Bowie from 1840’s-1850’s period with 8-15/16″ clip point blade, 1-1/2″ at ricasso with a 7-1/4″ back grind. It has a 3/16″ thick pointed oval German silver handguard with a coffin shaped handle of cast German silver that has stylized alligator pommel with ivory scales pinned with four German silver rivets and an elongated German silver shield on one side. Left ricasso is marked “WOODHEAD & HARTLEY / 36 HOWARD STREET / SHEFFIELD”. This knife is identical in shape but slightly larger than one pictured on p. 89 of the book Bowie Knives of the Ben Palmer Collection, Palmer, Moran & Phillips with identical handle as another pictured on p. 245 of the book The Antique Bowie Knife Book, Adams, Voyles & Moss. Page 257 of the same book has a nearly identical knife but with different pommel that differs only with the more common half horse-half alligator motif but with identical blade shape, ricasso marking & ivory scales. These knives were a staple of the American Frontier prior to Civil War made famous by the intrepid James & Rezin Bowie. No self respecting frontiersman, cowboy or gentleman of that era would be caught without his knife. Being without one’s knife could cost someone his life. This knife, given its fancy & probably costly appearance, mostly likely would have belonged to someone of importance and/or of reasonable means. Accompanied by a homemade 1-pc leather sheath with spacer in sewn back edge. CONDITION: Fine. Shows some sharpening with a few small chips in cutting edge and light to moderate pitting, moreso on right side. Left side grip panel is cracked, otherwise handle is very fine with beautiful gold to orange age patina. Sheath shows heavy wear and is dark & stiff. 4-31233 JR419 (17,500-27,500)

RARE EARLY W. BUTCHER BOWIE KNIFE. Mid-1830’s style Bowie by W. Butcher with ricasso marked with a cypher of a “WR” and crown which is the royal cypher of William IV (1832-1836). Ricasso is also marked “SHEFFIELD”. This wonderful early knife has an 8-7/8″ slim clip point blade and is 14-1/16″ overall. Blade is 1-1/4″ wide at widest point with a 6-7/16″ back grind with Spanish notch and is 1/4″ thick at ricasso. Blade is flat ground and is etched full length of blade including back grind area with beautiful sweeping foliate arabesque patterns with a 2-3/8″ long x 1/4″ wide panel in center marked “ARKANSAS TOOTHPICK”. It has a flat, 3/32″ thick, German-silver handguard with rnd ends and German-silver bolster with ebony scales with beveled edges secured with four German-silver pins and a long narrow rectangle on each side. Top & bottom of handle are German-silver panels with a flat German-silver pommel cap. This knife is nearly identical to those found on pp. 343 & 375 of The Antique Bowie Knife Book, Adams, Voyles & Moss, but with slightly different shaped blades but by same maker. Another one of similar shape & size is found as fig. 37 on p. 35 of American Knives, Peterson. Accompanied by remnants of a very early leather sheath, missing its throat & tip. It has a hand sewn seam on rear center. Face has light incised decorations. CONDITION: Fine plus. Blade is a light gray metal color having been sharpened very little, if at all. It retains thin but very discernible etching on blade and has areas of fine pitting. Handle has cracked scales but is complete with much orig finish. Sheath shows heavy wear with losses at throat & tip. A truly fine early & rare Bowie suitable for any level of collector. 4-31234(11,000-14,000)

LARGE UNMARKED EARLY BOWIE KNIFE WITH BRASS SHEATH. Large early heavy Bowie with 12-1/8″ severe clip point blade, almost 18″ overall, with 2-7/16″ blade width at widest point which is 1/4″ thick. It has a deep ricasso with 1/4″ thick “S” shaped iron handguard with flat ball quillions and a massive crown stag handle in serpentine shape fitted over tang with three copper rivets. Opening in toe & bottom of stag handle has a Bondo-type gray filler. Accompanied by its orig brass sheath which is made of two pieces of molded brass, soldered together on edge seams. It has its orig buffalo hide frog held to sheath with two copper studs on front. This knife is very similar to the dust cover illustration of the book Classic Bowie Knives, Abels, which later was sold from the famous Charlie Schreiner, III collection in March of 1992. The Abels knife and this knife are almost identical with slightly different handguards and a silver-plated tin sheath on Abels knife, whereas this one is brass. These large blacksmith-made knifes were prevalent on frontier, not only for fighting but were tools for everyday living. They were a formidable weapon in hands of a skilled fighting man and substituted readily for an axe or digging tool as well as for dressing game. CONDITION: Blade shows recent sharpening, otherwise has a semi-cleaned weathered patina with moderate to heavy pitting which also extends to handguard & tang. Stag handle shows moderate wear with some fine patina on exposed steel. Copper rivets are a very dark blackish patina. Brass scabbard is a dark mustard patina with a couple of small openings on top edge and another on bottom. Frog is stiff & dry, slightly shrunken and appears to have been re-stitched in recent years. 4-31109 JR422 (5,000-10,000)

VERY RARE & EARLY W. BUTCHER BOWIE KNIFE SN . Made in the 1830’s, this beautiful knife has an 8-3/4” dbl edged dagger-style blade, diamond shaped, with beautiful etched panels on both sides consisting of foliate & floral patterns. It has a long ricasso with identical etching on both sides. One side of ricasso has the cipher of William IV (1832-36) consisting of “WR” on either side of a crown. Rest of markings are “W. BUTCHER / SHEFFIELD”. It has a 2-3/4” dbl ended German silver handguard with wide rnd finials and a most unusual solid German silver filigree handle. It has a rounded ribbed frame with solid engraved bolster and flat engraved pommel. Center of handle is a vine with leaves, three flower blossoms & a thistle blossom. Accompanied by its orig red leather covered sheath with German silver throat & tip and a decorative band about the middle. Throat has a ribbed frog stud on one side. Opposite side is engraved with initials “J.B.B.”. The identical initials are engraved on one side of pommel of knife. A very similar & nearly identical knife used by a Confederate colonel of the 4th Louisiana, was excavated at Fort Hudson. CONDITION: Very fine. Shows evidence of sharpening but retains about 80% brilliant orig polish on blade. One side of handle has a crack, otherwise handguard & handle are fine. Sheath has a crack near bottom, just above an old repair. Remainder of leather is sound showing moderate to heavy wear with 25-30% gold in embossing. A truly rare & desirable Bowie. 4-31550 JR599 (7,500-12,500)

FINE PRESENTATION OR EXHIBITION ALEXANDER SHEFFIELD BOWIE KNIFE. Large Bowie with 11-3/16″ clip-point blade, 16-3/8″ overall, with 1-13/16″ wide blade with 1-1/2″ ricasso and is 3/16″ thick. It has a 3/16″ thick German silver handguard with birdhead finials and German silver bolsters on a slightly tapered tang with bone grip scales secured with four copper & brass pins. Left ricasso is marked “ALEXANDER / SHEFFIELD”. It appears that all metal surfaces have an unusual nickel plating, including blade. Blade has a 4-5/8″ back grind, only on left side. This may have been an exhibition knife but certainly would have been a formidable weapon. CONDITION: Fine. Blade has been lightly sharpened exposing the copper wash base coating on steel blade along edge. Blade retains most of its orig nickel plating but is bubbled & flaked. Handguard has some exposed copper and retains most of its orig nickel. Bolsters retain virtually all of their orig nickel with exposed edges of tang flaked to about 60% nickel. This is an unusual Bowie to say the least. 4-31108 JR420 (2,500-3,500)

FINE BARNES & SONS BOWIE KNIFE. Early Barnes Bowie with 7-3/4″ flat ground clip-point blade, 12-1/2″ overall. Blade is 1-1/8″ at ricasso, with a rounded diamond shape, having a 2-1/4″ back grind. It is 3/16″ thick at ricasso, which is marked on left side “EDWARD / BARNES / & SONS”. Tang is 1/4″ thick making knife butt heavy and has applied repoussed German silver handles with a raised American eagle shield & olive branches in an oval in center and tortoise shell panels above & below oval. Handguard & pommel have raised acanthus leaves with a rear facing handguard, top & bottom. CONDITION: Fine. Blade has been repolished to a fine sheen with a few spots of light pitting, mostly on right side. Handle is fine with clear crisp decorations. Top right side of handguard is slightly damaged, possibly where polishing wheel slipped. 4-31549 JR423 (500-1,000)

FINE REPRODUCTION OF AN EARLY BOWIE KNIFE. Unusual Bowie with 9-1/2″ clip point blade, 14-5/8″ overall. Blade is 2″ at widest point with 1-3/4″ ricasso having a Spanish notch with scalloped file work at bottom of ricasso. It has a thin scalloped edge German silver handguard with German silver ferrule and a rnd ribbed bone handle with nickel plated brass pommel cap & button pommel. Blade is 3/16″ thick with unmarked ricasso and handle & tang are slightly offset to bottom. CONDITION: Very good to fine. Blade is clean with a couple of minor chips in sharp edge and fine scattered light pitting overall. Handguard & handle are fine showing light wear with exposed brass on pommel cap. 4-31110 JR421 (1,000-2,000)

AMES BOWIE KNIFE. This rare Ames-made Bowie knife with 10-1/4” clip point blade is pictured in its orig scabbard on p. 345 of Norm Flayderman’s marvelous book on American Bowie knives. Blade exhibits two 5” etched panels and is etched with manufacturer’s name “Ames Mfg. Co. / Chicopee, Mas.”. Brass 3-1/2” crossguard is similar to that found on Model 1849 Rifleman’s knives, also by Ames. Shaped, ebony handle ends in crown-shaped pommel. Leather scabbard has white metal mounts with strip connecting them CONDITION: Blade is gray/bright and smooth. Etched panels are very good, as is grip, pommel and guard. Scabbard mounts are good, over leather body with several tears and reductions, including one approx. 2-1/2” x 1/4”, which is missing to spine edge. 8-76220 JS219 (6,000-8,000)

MEDIUM SIZED FOLDING GERMAN HUNTING KNIFE WITH SHEATH. Classic folding hunting knife with 7-1/4″ blade, 12″ overall when open and 8-1/2″ when folded. It has a floating split German-silver handguard and German-silver bolsters with steel liners. It has fine stag scales with a small shield on one side and switchblade style folding blade release. Accompanied by its orig brass tipped leather sheath. CONDITION: Fine. Retains most of a professionally repolished blade with a repaired hinge pin. Scales are intact with fine condition. Sheath shows moderate to heavy wear, missing belt loop. 4-31545 JR432 (250-500)

FINE JONATHAN CROOKES ENGLISH FOLDING HUNTING KNIFE. Wonderful early English folder with 7-3/8″ narrow blade, 11-3/4″ when openoverall with floating split German silver handguard and beautiful rugged stag handle scales with German silver push button release and a spring tab lockback. It has brass liners with filed edges. Left side of blade has maker’s name & logo. CONDITION: Fine. Has been sharpened and now retains most of a repolish but still with some grind marks. Lock is a little loose but secure. Scales are outstanding with one hairline at back edge. 4-31546 JR433 (500-1,000)

DELUXE GERMAN SHORT HUNTING SWORD. Fine deluxe Hirschfanger by Carl Eickhorn with 13″ flat ground blade with gilt & blue decorated blade of very detailed boar hunting scene and a woodcock on one side with a hunter and a leaping stag & hind with an auerhan on the other. It has a large deep cast languet with a raebuck and oak leaf & acorn decorations. Handguard is “S” shaped with oak leaves on the shank & acorn finials with oak leaf & acorn decorated ferrules and a beautiful rnd stag handle having two gold acorns and intertwined initials in steel “WF”. It has a fox and spruce tree decorated pommel cap with triple acorn pommel. Accompanied by its orig brown leather sheath with gold plated throat & tip. Tip is deep cast in a hunting scene of a stag & dog. Throat has a triple acorn stud. CONDITION: Exceptionally fine. Appears to be new with minor nicks on sheath. Blade retains about all of its orig gilt & blue. 4-31547 JR427 (1,250-2,250)

FINE LARGE RANDALL ARKANSAS TOOTHPICK STYLE BOWIE KNIFE. Large Randall made Arkansas Toothpick with 12″ dbl edged blade that is 1-5/8″ at handguard. Handguard is 1/4″ brass in their classic Bowie style with stacked leather handle having their red, white & black spacers at each end. Accompanied by its orig brown leather Randall sheath with maker’s name & address on back and numbers “13” and “12”. Front has a full sewn stone pocket containing a white soft Arkansas pocket stone. CONDITION: Extremely fine. Retains about 95% of its orig polish with no evidence of sharpening. Handle is very fine with only a couple of minor nicks and sheath appears to never have been carried. 4-31555 JR430 (1,000-1,500)

INSCRIBED LARGE RANDALL CLASSIC BOWIE KNIFE. Early Bowie with 11-1/8″ clip point blade that is 2-3/8″ wide with maker’s name & address on one side and the name “RICHARD C. MARQUART” on right side. It has a 5/16″ thick brass handguard with stacked leather handle and thick red, white & black spacers with rnd brass pommel cap and brass nut. CONDITION: Very fine. Shows no evidence of ever having been sharpened and retains most of its orig polish with some light fine surface rust near tip on left side. Handle is extremely fine. 4-31554 JR431 (1,250-1,750)

MODEL 1880 HUNTING KNIFE. Fine Springfield Arsenal Model 1880 hunting knife with 8-1/2″ blade, 2″ wide with bronze handguard marked on one side “U.S. / SPRINGFIELD” and number “771” on other side. It has a machine turned round ribbed oak handle. Accompanied by first type brass & leather sheath with brass belt hook marked on back “R.I.A.”. These knives were routinely issued to troopers on frontier service and saw extensive use throughout the latter part of the Indian Wars. CONDITION: Very good. Sharp edge shows sharpening with numerous small nicks and retains a smooth metal patina. Handle shows moderate wear with some fine battering on pommel cap. Sheath is flexed at hanger end, otherwise is sound and retains most of its orig finish. Brass has well-aged patina. 4-32472 JR428 (1,000-2,000)

RARE KRAG BOWIE BAYONET. Usual configuration with 9″ clip point diamond shaped blade marked “1900” on left ricasso and “US” on right ricasso. It has standard hand guard with muzzle ring and wood grip panels with eagle head pommel. Accompanied by an orig steel scabbard with ball tip and stud on back side for the metal Krag-type belt hanger, which is missing. CONDITION: Fine. Blade retains a lightly cleaned gray patina with evidence of light sharpening and slightly rounded tip with some very fine surface pitting. Handle is fine. Sheath is a cleaned gray metal color with traces of orig finish in very sheltered areas. 8-87526 JR429 (1,350-1,750)

SET OF SIX LAMSON, GOODNOW & CO. CIVIL WAR ERA TABLE KNIVES. Mid-19th century set of knives with 4-3/4″ tapered, flat-ground blades with rounded ends & 1-pc integral raised ricasso and tapered tang with 2-pc flat bone grip scales that have beveled ends, secured with three brass pins. These are Civil War era knives as would have been found gracing the table of a middle class home. CONDITION: Fine. Minor staining on some of blades with all handle material intact retaining a wonderful mellow ivory-like patina. 4-31544 JR418 (100-300)

RARE WILL & FINCK 4-PIECE CARVING SET. Unusual set by the fine, rare San Francisco maker consisting of a carving knife with 10-1/4″ blade that has maker’s name on left side. There are two, one large & one small, meat forks with 3-pronged attached stands and have maker’s name on backs. These three pieces appear to be matching with silver ferrules and smooth ivory handles. Additionally there is an unmarked sharpening steel with silver spacer and rnd ivory handle with a scrimshawed “W”. None of other handles are marked. CONDITION: Knife blade is fine & thin showing heavy use with light stains. It has an age line in handle. Large fork is very fine showing light to moderate wear and has several small age lines in handle. Small fork has same amount of wear with only one age line. The sharpening steel is also very fine with a wonderful smooth handle. All four handles have a beautiful golden ivory patina. 4-31548 JR434 (1,000-2,000)

ULTRA-RARE COLT WALKER PERCUSSION REVOLVER ONE OF THE FINEST IN PRIVATE HANDS. SN : E COMPANY NO 23. Cal. 44. This revolver, numbered “E COMPANY NO 23″, is from the most scarce company issue of all the Walkers having had only about 120 revolvers issued while the other four Companies had anywhere from 175 to 220 revolvers issued. Our Walker has standard 9” oct to rnd bbl with German silver front sight and New York City address reading from cylinder to muzzle. Left side of bbl lug has full serial number as does left side of frame and butt of backstrap. Right side of bbl lug has usual “US” over “1847” partially obscured by wedge screw. Abbreviated serial number “E COMY NO 23” appears in very tiny letters on cylinder and trigger guard. Number “23” was observed on wedge, on cylinder pivot pin, on left side of front strap under grip, on front edge of frame between frame pins and inside toe of grip itself. A small “90” or “06” was observed on a flat between nipples at back of cylinder. Cylinder has usual oval stops with “MODEL U.S.M.R. / COLT’S PATENT” markings and Ranger/Indian fight scene. Rammer & handle appear to be old replacements with a 3rd Model Dragoon style horizontal latch at end of handle and a dovetailed latch stud having been fitted to bottom of bbl. Rammer is quite unusual with a rebated area on both sides for about 1-1/2″ back of pivot. Rammer screw & pivot screw both enter from right side. Trigger screw and cylinder stop screw do not extend through frame. It has 1-pc walnut grip with outline of “NWP” oval cartouche on left side and outline of “WAT” cartouche on right side. There are small inspector initials on various parts including a “B” on left shoulder of trigger guard, top flat of bbl and on the cylinder. Accompanied by an equally rare tooled, black leather Slim Jim holster made specifically for a Walker revolver, probably this revolver. It is overall 14″ long on back side, made of 1-pc folded bridle leather with sewn back edge, contoured to fit a Walker revolver with an open toe. Front of holster is tooled in a stamped diamond pattern with beautiful ribbed pattern over cylinder & trigger guard areas. Back of holster has a sewn-on belt loop. This Walker was discovered in the 1940’s by the renowned & greatly respected late James E. Serven in the mother lode country of the 49’er miners in California. Apparently after a long negotiation he was able to trade the bar owner, where he found it, other handguns & cash and kept it in his own collection and pictured it on p. 54 of his book Colt Firearms, and with its orig holster on p. 89 of same book. A letter to Mr. L. Allan Caperton, dated May 2, 1968, is the cover letter for very detailed information on how he acquired this Walker. The orig of both letters accompanies this revolver. Also accompanying is an orig black & white photograph of Mr. Serven holding this Walker & holster, both of which are readily identifiable in the photograph. Additionally accompanying is an orig letter dated July 6, 1976, along with a bill of sale from Herb Glass wherein he states that this “is the best Walker in existence in the category of no finish Walkers.” He further states “There are four or five better – but only because they have varying amounts of original blue.” Walkers have always been considered the Holy Grail to a Colt collector and this particular one is most special because of its high condition and thus a tremendous opportunity of any serious collector attempting to put together a comprehensive collection of important Colt revolvers. PROVENANCE: James E. Serven Collection; L. Allan Caperton Collection; Herb Glass; Charles W. Fritz, Norwood, Ohio; pictured in various Colt books CONDITION: Very fine. This may be one of, if not the finest Walker revolvers extant for sale in recent history. It retains traces of orig finish in most sheltered areas, particularly at bbl transition and in beveled radius of bbl lug, otherwise all of its iron retains a smooth gray metal patina with some fine pitting on left side of the bbl. All legends & numbers are legible and in some cases fairly crisp. Hammer nose has moderate pitting. Cylinder is one of finest Walker cylinders extant with all legends & numbers clean & clear and overall retains very generous amounts of the Ranger/Indian fight scene. Trigger guard is a medium mustard patina with deep stamped numbers. Backstrap condition matches rest of revolver with somewhat thinned number on butt. Grip is sound showing moderate to heavy wear with chipped toes with outlines of cartouches on both sides and retains a hand worn patina. Rammer & handle, as noted, match condition of other steel. Mechanics are fine, strong bright bore with scattered light pitting. Holster is completely sound with some slight flexing on front edge and light wear around toe and overall retains most of its orig black finish. A truly remarkable revolver with an outstanding & rare civilian belt holster. 4-33312(375,000-475,000)

RARE MARTIALLY MARKED FIRST MODEL COLT DRAGOON REVOLVER. SN 6367. Cal. 44. Usual configuration with 7-1/2″ oct to rnd bbl, German silver front sight, tiny “US” beneath “COLT’S PATENT” on left side of frame with brass grip frame & square back trigger guard and 1-pc walnut grip with clear “SK” for Samuel Keeler cartouche on left side and “WAT” for William A. Thornton cartouche on right side. It has small inspector initials on various parts. Cylinder has oval stops with usual markings. These first model dragoons were virtually 100% issued and rarely survive with any condition. CONDITION: Fine, all matching except wedge which is unnumbered. Bbl retains 25-30% thin orig blue, being mostly a blue/gray patina. It has traces of case colors on rammer & pivot. Cylinder is a smooth gray patina with traces of finish around back edge and retains about 75-80% Ranger-Indian fight scene. Safety pin is battered & gone but cylinder shows light use. Frame is a gray patina with traces of silvered case hardening. Grip frame is a medium brass patina. Grip is outstanding with light edge wear and a few minor nicks & scratches and retains a fine hand worn patina with its clear cartouches. Mechanics are fine, bright shiny bore with scattered fine pitting. 4-33313 JR348 (27,500-42,500)

MARTIALLY MARKED COLT 3RD MODEL DRAGOON PERCUSSION REVOLVER. SN 17545. Cal. 44. Fine late third model dragoon with 7-1/2″ oct to rnd bbl, German silver front sight with a 3-leaf express sight dovetailed into top flat that has two folding & one standing leaves. Cylinder has usual markings with Ranger/Indian fight scene. It has 4-screw frame cut for shoulder stock with extended fourth screw & flat head hammer screw. Left side of frame has “COLT’S PATENT” over a tiny “U.S.” It has brass trigger guard with iron backstrap and 1-pc walnut grip with crisp “CGC” cartouche for C.G. Chandler on left side and “WAT” cartouche on right side for Capt. William A. Thornton. There are small inspector initials on various parts. Accompanied by a very rare “GAYLORD” marked black leather dragoon sized flap holster with sewn rear edge, plug in toe, a belt loop on back with three rivets and large flap with tab for the brass stud. Few of these belt holsters for this heavy revolver were ever issued and not many of those survive today. CONDITION: Very good to fine, all matching including wedge. Traces of finish remain in most sheltered areas with dark case colors on rammer pivot. Cylinder is gray metal color and retains 60-70% Ranger/Indian fight scene. Frame retains mottled silvered case colors and hammer dark case colors. Trigger guard is a light mustard patina and backstrap a gray/brown patina. Grip has a gouge on left top side with other handling & use marks with both cartouches nice & clear and some light battering on bottom edges and overall retains a smooth hand worn patina. Mechanics are fine, strong bright bore with scattered fine pitting. Holster is somewhat dry and flexed in flap with some minor losses at front & rear edges. Tab is fragile and broken in one edge, otherwise retains most of its orig black finish. 4-59725 JR215 (15,000-25,000)

MARTIALLY MARKED COLT THIRD MODEL DRAGOON PERCUSSION REVOLVER. SN 17160. Cal. 44. Late third model with 7-1/2″ oct to rnd bbl, German silver front sight and 3-leaf sight dovetailed at back end of top flat. It has 4-screw grip frame, cut for stock with extended stock screws and has a tiny “US” beneath “COLT’S PATENT”. It has brass trigger guard with iron backstrap and 1-pc walnut grip with partially legible cartouches. There are small inspector marks on various parts. These fine revolvers saw service from date of issue through Civil War and afterward on frontier during the great expansion westward. CONDITION: Very good to fine, all matching including wedge. Bbl retains a mottled silver/brown patina with traces of case colors on rammer pivot. Cylinder is a gray/brown patina and retains about 25% Ranger-Indian fight scene. Four of six safety pins are prominent. Frame retains traces of case colors, being mostly a smooth brown patina. Trigger guard is a light mustard patina and backstrap is a mottled silver/brown patina. Grip is outstanding showing light wear with traces of finish having survived a cleaning. Mechanics are fine, strong bore with moderate pitting. 4-33333 JR346 (10,000-15,000)

SCARCE CONFEDERATE USED COLT 3RD MODEL DRAGOON PERCUSSION REVOLVER. SN 14978. Cal. 44. Usual configuration with 7-1/2″ oct to rnd bbl, usual New York address with German silver front sight. It has “COLT’S PATENT” on left side of frame with small inspector initials on various parts. It has vertical rammer latch and brass trigger guard & backstrap with 1-pc walnut grip. Top of backstrap has hand scratched initials, probably with point of a knife, “RHH”, with “CA6VA” and buttstrap has hand scratched legend “BTC” with balance obliterated. Bottom of each side of grip is stamped “CO A”. These markings indicate that this revolver was carried by a Confederate soldier with initials “RHH” who was in Company A of the 6th Virginia Battery or something like that. Regardless, for sure, it was with a unit called the 6th Virginia. Accompanied by a Confederate style flap holster of 1-pc medium weight black leather with sewn edge and toe plug with a riveted simple belt loop. Flap has two holes for a small brass stud. Back has stitching holes, apparently where the orig belt loop was lost & replaced. CONDITION: Good to very good, all matching including wedge. No orig finish remains, being a mottled, cleaned silver/gray patina with light to moderate surface pitting and heavy edge wear at muzzle. Cylinder is matching condition with no remaining scene. Frame & hammer are also matching condition with light fine pitting. Trigger guard & backstrap retain traces of orig silver plating, being a medium mustard patina. Grip has a repaired left toe & chipped right toe showing heavy wear with a hand worn patina. Mechanics are fine, strong bore with moderate to heavy pitting. Holster shows wear with crackled surface on folded edges with some losses of orig finish. There is a small tear at back edge of flap but overall it is solid & supple. 4-32954 JR389 (7,000-12,000)

SCARCE COLT HARTFORD LONDON 3RD MODEL DRAGOON PERCUSSION REVOLVER. SN 264. Cal. 44. Scarce Colt, one of only about 700 made prior to the Civil War. It has 7-1/2” oct to rnd bbl, German silver front sight with address “ADDRESS SAML COLT NEW YORK CITY” with dashes at each end. It has British proofs on left side of bbl lug and on cyl between the nipples. It has brass grip frame with beautiful, smooth, burl walnut 1-pc grip. Left side of frame has Colt’s patent with usual markings on cyl. CONDITION: About fine. Traces of orig finish remain in the most sheltered areas, being a cleaned silver metal color with some very fine pitting around muzzle and a few spots on bbl. Cyl retains 60-70% Ormsby dragoon & Indian fight scene. All six of the safety pins are present. Grip frame is a light mustard patina. Grip is sound with a few dings on bottom & light handling & use marks and retains most of its strong orig varnish. Mechanics are fine, strong bright bore with some light frosty pitting. 4-30620 JL42 (7,000-9,000)

CASED COLT MODEL 1860 ARMY REVOLVER. SN 173222. Cal. 44. Spectacular cased Army with 8″ rnd bbl, German silver front sight and rebated cylinder with Ormsby naval battle scene. It has a silver plated trigger guard with iron backstrap & 1-pc walnut grip. Accompanied by its orig, blue velvet lined Colt casing compartmented in bottom for the revolver, a fine “COLT’S PATENT” angle spout flask and a blued 2-cavity “COLT’S PATENT” mold with “D” inspector initial on right side. Rear corner compartment contains a tall tin of Eley’s caps with another compartment containing lead bullets and a key. Flask is the deep repoussed stand of flags and trophy of arms style. CONDITION: Extremely fine, all matching including wedge. Bbl retains 88-90% glossy orig blue with loss areas flaked to medium patina. Rammer & handle retain about all of their orig case colors, very bright in sheltered areas. Cylinder retains 40-50% orig blue, strong in rebated area, flaked to light patina elsewhere and retains 97-98% orig Naval battlescene. Four of six safety pins are prominent. Frame retains virtually all of its bright orig case colors, dark on recoil shields. Hammer retains 70-75% strong orig case colors. Backstrap retains about 40% orig blue, flaked to light patina in middle. Trigger guard retains 15-20% orig silver with balance a medium mustard patina. Mechanics are crisp, brilliant shiny bore with a few scattered spots of light pitting. Case has a grain check in lid, otherwise is completely sound with a slightly warped lid and light soil & wear on interior. Flask retains about 90% orig finish with one small dent and the mold, most of its orig blue. Altogether a beautiful orig cased set. 4-32778 JR181 (20,000-30,000)

SCARCE SPRINGFIELD REWORK COLT MODEL 1860 ARMY PERCUSSION REVOLVER FROM FAMOUS 10TH CAVALRY. SN 140869. Cal. 44. Until recently it was thought that these mismatched Armys with large “US” stamped in brass trigger guard were simply that, mismatched Armys. However, several recent articles have disclosed that they are revolvers that were reworked at Springfield with no regard for serial numbers. At this point little more is known about them. This Colt, however has a somewhat more famous history having been issued to F Troop of the famous 10th Cav. Regiment, The Buffalo Soldiers. Formed in 1866 as an all African-American regiment, the 10th spent the next twenty years being stationed all over Kansas for eight years and in 1875 were transfered to Fort Concho in West Texas to help control the Comanche & the Apaches. Some of their most important skirmishes were in the 1879-80 campaign against Apache Chief Victorio, eventually driving him & his band back into Mexico where they were nearly wiped out by the Mexican military in 1880. In 1885 the 10th was again transferred, this time to the Department of Arizona where they participated in the fight against Geronimo, Nana, Natchez, Chihuahua & Mangus. In 1891 they were transferred to the Department of Dakota and served at various posts in Montana & the Dakotas until 1898. They further participated in the 1916-17 Mexican expedition in retaliation for Pancho Villa’s raids. The unit still exists today and still participates in modern military fashion fighting where needed. This revolver has 7-7/8″ rnd bbl having been re-crowned at some point during its period of use. The bbl address is nearly worn away. Cylinder number is barely legible. It has a 3-screw frame cut for shoulder stock with brass trigger guard & iron backstrap with 1-pc walnut grip. It is completely mismatched with bbl having serial number “130645”, wedge “7652”, cylinder “0281”, frame “140869”, trigger guard “140500” & buttstrap “11933”. There is a large “US” stamped into the triggerguard just in front of the trigger bow. It is also stamped on the right side of the trigger guard frame “F 10 CAV.”. CONDITION: Good to very good. No orig finish remains with bbl & cylinder a dark attic patina. Frame is a dark mottled silver/brown patina with replaced hammer screw and moderate pitting on hammer nose. Trigger guard is a light brass patina and backstrap a dark patina. Grip is sound with chipped toes and showing heavy wear. Mechanics are fine although a little loose with a worn dark bore. 4-33335 JR399 (7,000-10,000)

FULLY IDENTIFIED SERGEANT’S WEAPONS GROUPING, 1ST NEW YORK MOUNTED RIFLES. This group consists of three weapons (carbine, pistol, and sword) that date to the war service of Sgt William H. Armstrong of Troop B, the 1st NY Mounted Rifles (NYMR). The 1st NYMR (sometimes designated as the 7th NY Cavalry) was in service during the entire war from July 1861 to July 1865. The list of expeditions and engagements is too long and numerous to detail. William Armstrong enlisted as a Pvt in Troop B on Oct 1, 1861 in New York City. He served the entire war, being promoted through the ranks to Cpl, Sgt, 1st Sgt, and 2nd Lieutenant, but not being mustered as 2nd Lt. He mustered out in July 1865 in Richmond, VA. Both the Spencer carbine and Colt Army pistol have engraved German silver plaques applied to the pieces indicating ownership and service details. The engraving on the German silver plaques appears to date to just after the Civil War, likely being added to commemorate Armstrong’s service. All three items have an extremely old coating of dull nickel plating that is beginning to darken with age. The nickel had aged to a pleasant gray color and is not openly apparent at first review. The combination of the nickel coating and German silver plaques suggest that the items might have been displayed together, perhaps at a Union GAR Hall. The model 1860 4 screw Colt .44 caliber Army percussion pistol has some darkened rust patina on about 6” of bbl. Bbl near muzzle is worn down slightly from years of holster wear. There is an approx. 3” long German silver plaque inset and tacked into left grip that reads “Sergeant W. H. Armstrong / 1st N.Y.M.R. ’61-65”. The gun’s serial numbers are mismatched from frame, bbl assembly and cyl, but this is the way the gun was actually used and all the numbers are extremely close. Cyl is marked with SN 128xx, bbl assembly with SN 1034x, and frame with SN 1039x. Gun supports the claims that actual used guns had parts swapped, while only the mint guns have matching serial numbers. The group’s Model 1860 Light Cavalry sword is maker marked by “Emerson & Silver / Trenton, NJ”. Blade is “US” surcharged with inspector’s stamp “J.M.”. No date can be seen, but the orig leather washer is present and appears to be hiding the marks. Blade shows condition consistent with use and has a center area with old pitting. Leather grip and wire wrap are orig and present in excellent condition. “J.M.” inspector mark is also present on the sword’s hilt capstan. Scabbard is old gray nickel with selected darkening and light rust. The Model 1860 Spencer carbine, SN 57xxx, is a late war carbine. Government documentation shows that the 1st NYMR were issued the Spencer carbine right near the end of the unit’s service. This carbine has been nickel-plated with all exterior plating having turned a pleasing dark rust patina. Carbine’s federal inspector marks (two sets near the ring bar) are showing and can be seen, but are beginning to fade. Rear sight appears to have been missing for some time. ON the carbine’s left side of the stock is inset a German silver plaque (4-1/2” x 1-1/4”) with tacks, engraved “Sergeant W. H. Armstrong / 1st N.Y.M.R. ’61-65”. This is a very unique and rare, fully identified weapons grouping to a single soldier that served in the mounted service through the entire war. CONDITION: All three weapons have varying degrees of nickel plating remaining. Spencer carbine is very good and above average overall with most metal surfaces with plating missing being brown and pitted. Bbl address is discernible. Bore is very good with strong rifling. Inspector cartouches are still visible on buttstock. Stock retains traces of orig varnish with scattered nicks, scrapes, and gouges. Colt Army is sound and functions mechanically. Markings are all discernible, including part of cyl scene, which is visible under plating. Cavalry saber has very good grip with good patina to brass. Blade is gray and cleaned with areas of pitting. Nickel plating on scabbard is consistent with color on carbine and pistol. Commemorative plaques on carbine and pistol are uncleaned and exhibit good patination. 4-32929 JS257 (6,000-7,500)

CASED COLT MODEL 1851 NAVY REVOLVER. SN 68335. Cal. 36. SN 68335. Fine cased Navy with 7-1/2” oct bbl, brass cone front sight and 1-line New York City address with dashes. It has usual 6-shot cylinder with an asterisk and a “W” stamped by center pivot on face. Frame has “COLTS PATENT” on left side and it has the rare silver plated iron trigger guard & backstrap and rounded large trigger guard and it has smooth 1-pc ivory grips. All serial numbers on bottom of revolver are stamped with an “I” beneath them which is a generally accepted indicator of factory ivory grips. Accompanied by its orig green velvet lined, walnut casing compartmented in bottom for revolver, a fine angle spout, dbl sided Colt’s flask, a blued iron 2-cavity “COLTS PATENT” mold, a packet of combustible cartridges and a lacquered tin of Eley’s caps. Right rear compartment contains a number of lead balls & conical bullets and the functioning key to case. Case has a shield shaped brass escutcheon on front for mortised brass lock. CONDITION: Very fine, all matching including wedge. Bbl retains 70-75% orig blue with loss areas flaked, not worn to a medium patina. Rammer handle retains bright case colors on pivot. Cylinder retains 40-50% thin blue with balance flaked to a medium patina and it retains about 95% Ormsby Naval battle scene. Five of six safety pins are mostly intact. Frame retains about all of its orig case colors, strong & bright on sides and turned a little dark on recoil shields. Hammer retains 60-70% strong case colors, mostly on sides & back edge. Trigger guard retains about 90% strong orig silver plating & backstrap about 80%. Grip has a chipped left toe and a few age lines in bottom with one long age line on right side and overall retains a beautiful mellow ivory patina. Mechanics are crisp, bright shiny bore with a few scattered spots of light pitting. Case has a few very fine grain checks in both top & bottom with normal handling & storage nicks & scratches and retains most of its orig finish. Interior is lightly faded, showing wear from three or four points of revolver contact with all partitions solid. Flask has a couple of small dents and retains about 95% strong orig finish. Cartridge packet is crisp with mold retaining about 95% orig blue. Cap tin is also crisp. A truly wonderful set in outstanding condition. 4-32779 JS467 (20,000-30,000)

COLT MODEL 1851 NAVY REVOLVER. SN 16278. Cal. 36. Fine early third model with 7-1/2″ oct bbl, 1-line New York City address with dashes, silver plated brass grip frame with small rnd trigger guard and 1-pc walnut grip. It has thin lug and beveled v-notch. There are small inspector initials on some parts with a tiny “G” below serial number, an “R” on left web and a horizontal “T” on right shoulder of trigger guard. There is a tiny “W” on cylinder. It has standard 6-shot cylinder with rolled Ormsby’s Naval battle scene. CONDITION: Very fine to extremely fine, all matching including wedge. Bbl retains about 65-70% strong, glossy orig blue with flaked areas a light patina. Rammer pivot retains strong case colors on both sides with faded colors on handle. Cylinder retains 93-95% glossy orig blue and about all of its orig Ormsby Naval battle scene. Three of safety pins are completely intact. Frame retains most of its orig case colors, dark & faded on recoil shields, strong in sheltered areas. Hammer retains dark case colors with some fine pitting. Grip frame retains about all of its black oxidized silver plating with only traces of brass showing through. Grip has a tiny chip in right toe and a minor nick or two and retains about all of its orig varnish. Mechanics are crisp, brilliant shiny bore with a few scattered spots of pitting. A rare early Navy with outstanding condition. 4-31527 JR179 (10,000-15,000)

MARTIALLY MARKED COLT MODEL 1851 NAVY ARMY REVOLVER. SN 56171. Cal. 36. Fine 3rd model martial ’51 with 7-1/2″ oct bbl, brass cone front sight and 1-line “NEW YORK CITY” address with dashes. It has usual Ormsby naval battle scene on cylinder & “COLT’S PATENT” over a tiny “U.S.” on left side of frame. It has brass grip frame with 1-pc walnut grip having a legible “LCA” cartouche in an oval on left side (the only “LCA” inspector this cataloger could discover was for Lucius C. Allin who was a Colt Dragoon inspector) and an “RHKW” cartouche in an oval on right side for Capt. Robert Henry Kirkwood Whitley. Various parts have small “A” inspector initials (indicating O.W. Ainsworth sub-inspector) including backstrap at top, grip at bottom left side and top of left side, upside down on right shoulder of trigger guard, on bbl lug & cylinder. All six safety pins on cylinder are prominent and cylinder has vice marks on opposite sides. CONDITION: Fine to very fine, all matching including wedge. Bbl retains a thin blue/brown patina but shows very little wear with a few scattered spots of fine pitting. Rammer pivot has some bright case colors with a spot of pitting on right side. Cylinder retains virtually all of a light restored finish, not having been polished with the aforementioned vice marks. It also retains about 60-70% crisp Ormsby naval battle scene. Frame retains 70-75% faded case colors turning silver with some light surface discoloration. Hammer retains about 50% faded case colors with light pitting around nose. Grip frame is crisp with a medium mustard patina. Grip is extremely fine showing very light wear with a few minor scratches & nicks and retains most of its orig varnish with a crisp cartouche on right side, somewhat thinner cartouche on left side, probably from a light strike. Mechanics are crisp, bright shiny bore with scattered light pitting. 4-31220 JR199 (7,000-11,000)

WONDERFUL INSCRIBED DAMASCENED COLT LONDON MODEL 1851 NAVY REVOLVER OF A VICTORIA CROSS WINNER. SN 11931. Cal. 36. Usual configuration with 7-1/2″ oct bbl, London address, with iron trigger guard & backstrap and checkered 1-pc walnut grip. Left side of frame has “COLT’S PATENT” and backstrap is engraved in period script “Thomas Adair Butler / 101st Regt.” This beautiful revolver has foliate & floral gold Damascene patterns on bbl lug, rammer handle, frame, recoil shields & trigger guard with fine geometric patterns on cylinder & top of backstrap. The area on frame with “COLT’S PATENT” has a smooth gold panel with matching blank panel on opposite side. Rear sides of frame has gold flower blossoms with platinum branches. It is not believed that Colt ever produced such decoration on one of their revolvers, but it is known that individual officers had them so decorated in India and a few in England. Thomas Adair Butler was born Feb. 12, 1836 at Soburton, Hampshire, England and died May 17, 1901 at Lindale, Camberley, England. Butler enlisted as a 2nd Lieutenant in the 101st Regiment of Royal Bengal Fusiliers on June 9, 1854, became a lieutenant on Nov. 23, 1856 and eventually retired as a colonel. Lt. Butler was posted to India with the 101st to quell the Indian mutiny and participated in most of the battles in 1857 & 1858. On March 9, 1858, Lt. Butler gallantly swam the Goomtee River under heavy fire, to survey the enemy emplacements at Lucknow, for which he was awarded the Victoria Cross, England’s highest military award for valor. During one of the other campaigns he was slightly wounded, apparently not seriously. One “after action report” has Lt. Butler, during one of battles in India, shooting an enemy at close range with his revolver, probably this same Colt. He remained in the service of the 101st and became captain in 1863, serving in the Northwest Frontier campaign in that year and participated in a number of battles, for which he was additionally decorated. Apparently at one time the medal was stolen and resurfaced in 1963. As of July 1989 Lt. (later Maj.) Butler’s Victoria Cross Medal was on loan to the Military Academy at Sandhurst. Accompanied by a copy of a newspaper article from the London Daily Telegraph, Oct. 10, 1972, which reports the sale of this revolver for 1,000 pounds. Also accompanied by other newspaper articles & several regimental listings and regimental action reports mentioning Butler. This is a revolver that belonged to a brave & daring young soldier and undoubtedly saw service with him in India where the damascening was probably applied. Butler’s action at Lucknow was the subject of a painting by Chevalier L.W. Desanges in the Victoria Cross Gallery at Wantage, Berkshire, England. CONDITION: Very fine plus, all matching including wedge. Bbl, rammer & handle all retain most of their fine bright blue with a few spots of touch-up over some light pitting. Cylinder & frame also retain most of this fine blue with a cleaned spot around the damascening on rear edges. Trigger guard retains about 50% strong blue, mostly in sheltered areas and backstrap is a blue/gray patina. Cylinder retains about half of all six safety pins. Mechanics are fine, bright shiny bore. 4-33303 JR350 (17,500-22,500)

MARTIALLY MARKED COLT MODEL 1851 BLACK NAVY NAVY REVOLVER. SN 89901. Cal. 36. Fine Navy Navy with 7-1/2″ oct bbl, brass cone front sight that appears to have been soldered in place and Hartford address. It has usual straight cylinder with Naval battle scene and 3-screw frame, not cut for shoulder stock and a tiny “U.S.” beneath “COLT’S PATENT” on left side. It has large iron trigger guard & back strap with 1-pc walnut grip. Buttstrap is stamped “USN” with stars and left side of bottom of grip is stamped “I / GWR” with stars, for Commander George W. Rogers. CONDITION: Very fine to extremely fine, all matching including wedge & rammer, grip was not checked. Bbl retains about 90% orig blue, slightly thinned. Rammer pivot retains most of its lightly faded case colors. Cylinder is flaked to a light gray patina and retains 93-95% Ormsby Naval battle scene. Five of six safety pins on back are prominent. Frame retains 60-70% faded case colors, stronger on right side and hammer about 80% bright case colors, faded to gray on top. Trigger guard & backstrap are mostly a gray patina with blue in sheltered areas. Grip is crisp & sound with light wear and retains most of its orig oil finish. Mechanics are crisp, bright shiny bore with scattered pitting. 4-33314 JR366 (17,500-25,000)

MARTIALLY MARKED COLT MODEL 1851 BLACK NAVY NAVY PERCUSSION REVOLVER. SN 90744. Cal. 36. Usual configuration with 7-1/2″ oct bbl, brass pin front sight & Hartford address. It has a tiny “U.S.” below “COLT’S PATENT” on left side of frame and tiny inspector initials on some of parts. Buttstrap is not marked which is not uncommon for these revolvers. It has usual unfluted 6-shot cylinder with naval battle scene. CONDITION: Very good to fine, all matching including wedge & rammer; grip was not checked. Bbl retains an overall thin blue/gray patina with some scattered fine holster pitting, mostly on right side. Rammer pivot retains bright case colors. Cylinder is a gray/brown patina with all six safety pins prominent and retains 75-80% Ormsby Naval battle scene with a couple of spots of pitting. Frame retains about 85% orig case colors, strong on right side, more faded on left side. Grip frame is a gray metal patina with some light pitting on front of trigger guard and a few pinpoints of pitting on backstrap. Grip is sound showing moderate wear with a hand worn patina. Mechanics are crisp, strong bright bore with scattered pitting. 4-33334 JR367 (3,500-6,000)

COLT MODEL 1851 LONDON NAVY PERCUSSION REVOLVER. SN 40233. Cal. 36. Usual configuration with 7-1/2″ oct bbl, brass cone front sight & London address. It has British proofs on left side of bbl lug & on cylinder. Left side of frame has “COLT’S PATENT” and it has large rounded iron trigger guard & iron backstrap with 1-pc walnut grip. Only about 40,000 of these London Navies were ever produced. With this one, a Hartford London, ie., made in Hartford with London address & shipped to Colt’s London Agency. CONDITION: Fine, all matching including wedge, grip was not checked. All metal retains a mottled medium patina with some very fine pitting around muzzle and front edge of cylinder. Cylinder retains 40-50% Ormsby Naval battle scene & has four of six safety pins. Grip shows moderate wear and retains 92-94% strong orig varnish. Mechanics are fine, strong bright bore with a few scattered spots of pitting. Wedge spring is present but loose in slot. 4-59728 JR392 (1,500-2,500)

Revised: 10/19/2007

Correction)Gun is a period copy of a Colt, is an antique.

ENGRAVED COLT MODEL 1851 NAVY REVOLVER. SN 100175. Cal. 36. Silver finish with 7-1/2” oct bbl, pin front sight with brass trigger guard & backstrap and 1-pc walnut grip. Frame has full coverage, typical Nimschke engraving with Colt’s Patent on left side. Engraving extends over the entire sides of bbl lug & rammer pivot with a border around the address on top flat. Backstrap, buttstrap & trigger guard are engraved to match. CONDITION: Fine to very fine. This is a little used revolver that has had poor storage. Bbl & rammer handle retain 75-80% strong re-silver with some flaking (mostly near the end of the bbl and the plunger) and turning dull. Flaked areas are a dark patina. Cyl retains about 85% re-silver plating with about 95-98% crisp Ormsby naval battle scene. All six safety pins are crisp. Frame retains 80-85% silver plating with flaked areas dark patina. Grip frame retains about 95% silver plating, thinned on backstrap. Ends of wedge show little or no battering with most of their engraving intact. Replaced grips are crisp with sharp edges and retain virtually all of their orig factory varnish. Trigger return spring is weak, otherwise mechanics are crisp with bright shiny bore. 4-87520 JJ33 (10,000-15,000)

COLT MODEL 1851 NAVY REVOLVER. SN 117058. Cal. 36. Usual configuration with 7-1/2″ oct bbl, New York address, with brass trigger guard & backstrap and replacement 2-pc walnut grips. Accompanied by a reproduction black military holster. PROVENANCE: Glenn Marsh Collection. CONDITION: Good to very good, all matching except wedge which is numbered “2245”. No orig finish remains being a dark attic patina showing moderate to heavy wear on all sharp edges. Cylinder retains traces of Ormsby Naval battle scene with grip frame having a wonderful mellow mustard patina. Grips are fine. Mechanics are a little loose but functioning, strong bore with moderate pitting. Holster is near new. 4-59627 JR402 (500-1,000)

EARLY COLT MODEL 1851 NAVY REVOLVER. SN 19127. Cal. 36. Probably Confederate used Colt with 7-1/2″ oct bbl, New York City address with replacement dovetailed German silver Rocky Mtn. front sight and a small fixed rear sight dovetailed through address. It has 3-screw frame with small “COLT’S PATENT” on left front side with silver plated brass grip frame with small rnd trigger guard & very nicely figured 1-pc walnut grip. Accompanied by a Confederate-style left hand Slim Jim holster made of heavy belting leather with coarse decorated front side with sewn back edge, without plug, and a sturdy sewn & riveted belt loop on back. Holster has carried this revolver for a very long time as it has a bump where the rear sight is located. PROVENANCE: Glenn Marsh Collection. CONDITION: Fair, all matching including wedge. No orig finish remains, being a worn mottled gray/brown patina with light scattered pitting. Cylinder is moderately battered with no Ormsby Naval battle scene remaining. Frame screws have been dressed while grip frame screws all have slipped slots. Grip has a chipped toe with some scattered battering on bottom, shows heavy wear with dark hand worn finish. Rammer pivot screw & bbl lug screw have been dressed. Mechanics are fine, strong dark bore with moderate pitting and a few spots of heavier pitting. Holster is strong, having been restitched, and retains a wonderful dark russet finish. 4-59619 JR384 (500-1,000)

COLT MODEL 1861 NAVY U.S. NAVY NAVY REVOLVER. SN 6863. Cal. 36. Usual configuration with 7-1/2″ rnd bbl, German silver front sight & New York address. It has 1860 Army-style rack & pinion rammer with “COLT’S PATENT” on left side of frame. It has brass trigger guard & backstrap with 1-pc walnut grip. Accompanied by a Colt Factory letter identifying this revolver as having been shipped to the Navy in New York, probably the Brooklyn Navy Yard on March 5, 1862 in a shipment of 300 same type firearms. CONDITION: Fine to very fine, all matching except wedge which is numbered “883” vs. the last three digits of serial number which is “863”, possibly a field switch. Bbl retains 50-60% orig blue, strong & bright in sheltered areas, flaked to dark patina elsewhere. It has good feathers around front sight. Rammer pivot retains strong case colors. Cylinder has an area of deep pitting with no finish remaining being a gray/brown patina with remaining Ormsby Naval battle scene being sharp. All six safety pins are crisp. Frame retains about 70% strong case colors, bright on right side with recoil shields turned dark with some very fine pitting. Trigger guard & backstrap are a light brass patina. Grip is sound showing moderate wear with a hand worn patina. Mechanics are crisp, bright shiny bore with scattered pitting. 4-32832(8,500-10,500)

SCARCE COLT MODEL 1861 NAVY PERCUSSION REVOLVER WITH CONFEDERATE STYLE HOLSTER. SN 4357. Cal. 36. Usual configuration with 7-1/2″ rnd bbl, German silver front sight, New York address with “COLT’S PATENT” on left side of frame. It has silver plated brass trigger guard & backstrap with 1-pc walnut grip. Accompanied by a wonderful Confederate style Slim Jim black leather holster with narrow flap that fits through a keeper strap & has a belt loop sewn to back. It appears to have been made from recycled saddle leather as there are visible rows of old stitching. Toe plug is missing. CONDITION: Very fine, all matching including wedge. Grip number was not checked. Bbl retains 30-40% thin orig blue, strong in bottom of bbl & in sheltered areas. Cylinder is a gray patina and retains 25-30% Ormsby Naval battle scene. Frame retains 75-80% strong orig case colors, turned dark on recoil shields and hammer retains about 50% dark colors. Grip frame retains 50-60% thin orig silver plating, strong around trigger guard. Grip has a chipped left toe and shows moderate wear with a fine hand worn patina. Mechanics are fine, strong bore with scattered pitting. Holster has a crackled surface with flexed flap bend and retains about 70% orig black finish 4-59727 JR397 (3,500-5,000)

MARTIALLY MARKED COLT MODEL 1861 NAVY REVOLVER. SN 5256. Cal. 36. Usual configuration with 7-1/2″ rnd bbl, German silver front sight & “COLT’S PATENT” on left side of frame with brass trigger guard & backstrap and 1-pc walnut grip. It has small inspector initials on various parts. Accompanied by a Colt factory letter identifying this revolver with 8″ bbl (obviously a ledger entry mistake), as having been shipped to Lt. Col. G.D. Ramsey, Washington, D.C., probably the Washington Naval Shipyard, on Feb. 7, 1862 in a shipment of 500 same type firearms. This obviously was a Civil War issued & used Colt. CONDITION: Fine, all matching including wedge. Iron overall retains a smooth medium to dark patina with a few scattered spots of fine pitting and heavy holster wear at right edge of muzzle. Cylinder retains 15-20% Ormsby Naval battle scene. Grip frame is a cleaned light brass patina. Grips are sound with chipped toes & battered bottom edges with moderate nicks & dings and retains most of an old cleaned patina. Mechanics are fine, strong bore with moderate to heavy pitting. 4-33315 JR347 (3,500-5,000)

COLT MODEL 1861 NAVY PERCUSSION REVOLVER. SN 4225. Cal. 36. Usual configuration with 7-1/2″ rnd bbl, New York address with German silver front sight. It has “COLT’S PATENT” on left side of frame & “36 CAL.” on left shoulder of trigger guard. It has brass trigger guard & backstrap with 1-pc walnut grip. Accompanied by a Colt factory letter identifying this revolver as having been shipped Dec. 19, 1861 to New York Navy Yard. CONDITION: Very good, all matching including wedge; grip was not checked. No orig finish remains, being a smooth even gray/brown patina with light vice marks on both sides of bbl. Cylinder retains about 20% Ormsby Naval battle scene and has partial safety pins. Screws are fine in frame and grip frame retains a light mellow brass color. Grip has a chipped toe with some light battering on bottom and retains a hand worn patina. Mechanics are fine, strong bore with moderate pitting. 4-33350 JR368 (1,000-2,000)

Revised: 10/19/2007

(Additional Information) Consignor notes that this was purchased from Norm Flayderman

FINE FIRST MODEL COLT DRAGOON OR WALKER FLASK. Great flask with copper body & brass collar secured with three screws, a “35 grs” spring loaded charger, and a “COLT’S PATENT” marked cap cover. It has inspector initials “WAT” and a tiny “P” proof on top cover. Body of flask is dbl sided with repoussed trophy of arms with Texas & American flags in background, a stand of pikes, cannon and other arms over a pair of crossed Paterson rifles which is over a pair of crossed flared butt revolvers with a ribbon across bottom marked “COLT’S PATENT” without a star in middle. It has eyelets on each side with triangular shaped brass rings. These flasks are pictured as flask numbers 825-830 in The Powder Flask Book, Riling, and appears to be closest to item #827. It is this cataloger’s understanding that these large early flasks, with inspector marks, were made for the Walker but no positive statement can be made at this time. CONDITION: Fine to very fine. Traces of orig finish remain in most sheltered areas being mostly a medium copper patina with a number of nicks & dings on neck but no major dents. Seams are sound with top & spout having a dark brass patina. A really fine early Colt flask. 4-32414 JR414 (2,000-4,000)

FINE EARLY COLT DRAGOON FLASK. Great flask with copper body & brass collar secured with three screws, a “35 grs” spring loaded charger, and a “COLT’S PATENT” marked cap cover. Body of flask is dbl sided with repoussed trophy of arms with Texas & American flags in background, a stand of pikes, cannon and other arms over a pair of crossed Paterson rifles which is over a pair of crossed flared butt revolvers with a ribbon across bottom marked “COLT’S PATENT” without a star in middle. It has eyelets on each side with triangular shaped brass rings. These flasks are pictured as flask numbers 825-830 in The Powder Flask Book, Riling, and appears to be closest to item #827. CONDITION: Very good to fine. Retains traces of orig finish in most sheltered areas being mostly a dark copper patina with a few light nicks & dings and a dent on one side with another dent on bottom edge and a slightly open seam. Plunger seams to be frozen. 4-33575 JR415 (1,500-2,500)

LOT OF THREE PEACE FLASKS. 1) Ames Circle of Stars Peace Flask. Dated “1838” with markings on top of brass toe. It has a dbl sided copper body with usual markings and inspector initials “WS” by eagle’s head on one side. It has eyelets on each side with triangular rings level with eagle. 2) Batty Oval of Stars Peace Flask. Top is marked “BATTY” and date “1851” with inspector initials “RDK”. Accompanied by extremely rare orig leather shoulder strap with brass hooks. Strap appears to have been buff colored leather. Batty flasks differ slightly from Ames flasks with dbl sided decorations slightly smaller. 3) Batty Peace Flask. Undated with sgl “K” inspector mark on top and “ADK” on side of collar. Basically identical to #2 but with triangular rings. CONDITION: 1) Very fine. Overall retains a very dark brown patina with one very minor dent on lower bottom side by seam. Spring is good, spout is frozen. 2) Fine to very fine. It has small dent on each side, about center, otherwise is completely sound with good spring & functioning spout and overal retains a very dark patina. Strap is stiff & brittle, in need of treating. 3) Fine to very fine. It has a few small dents on one side and a sgl small dent on other side just below collar, otherwise is completely sound with good spring and functioning spout. 4-335704-33571, 4-33572 JR416 (2,500-4,000)

Revised: 10/19/2007

(Correction)Flask is a repro

COLT MODEL 1860 ARMY FLASK. Fine copper & brass flask with sloping charger and 1-sided deep repoussed decoration with usual trophy of arms & flags with crossed rifles & crossed revolvers at top, centered over “COLT’S PATENT”. Rilings No. 816. CONDITION: Good to very good. Overall retains 50-60% orig finish with exposed areas a dark copper patina. Face of flask has one small dent above crossed rifles and a larger dent centered on back. Bottom seam has small open spots with a couple of other light dents. Overall a fine flask. 4-32418 JR417 (400-800)

RARE CASED COLT BABY DRAGOON PERCUSSION REVOLVER SN 8219. Cal. 31. Rare baby dragoon with 5” oct bbl, German silver pin front sight with 2-line New York City address with dashes reading from cylinder to muzzle. Made without rammer. It has 5-shot cylinder with oval stop holes without leads and has the Ranger/Indian fight scene. Frame has “COLTS PATENT” on left side with silver plated brass trigger guard & backstrap with 1-pc walnut grip. Trigger guard has the square back. According to Flayderman’s Guide to Antique American Firearms, about 15,000 of these revolvers were produced in period 1847-1850. Accompanied by a very early, extremely rare, orig mahogany Colt casing with fluted edges on lid and blue velvet lining with recesses & wire retainers in bottom like the orig Paterson casings. Bottom is recessed for revolver, a fine early “COLTS PATENT” dbl sided flask with repoussed eagle facing to its right holding a Walker revolver & flask in its talons with grasses & three rows of balls below. Also accompanying is a brass “COLTS PATENT” 2-cavity mold without sprue cutter. Bottom of mold is stamped with initials “OMH” and top left has a tiny “S” inspector initial. Additionally accompanying is a rare, orig nipple wrench/screwdriver. Finally, a tin of caps with suspicious Eley label. In right rear corner is a triangle compartment containing lead balls and a case key. Very few baby dragoons were cased and extremely few of those have this early style of casing. CONDITION: Very good to fine, all matching except wedge which is unnumbered. Bbl retains traces of orig blue mixed with dark brown patina with a couple of dings on top flat. Cylinder is a gray/brown patina with scattered dents & dings and retains about 30% Ranger/Indian fight scene. Frame is a gray/brown patina with traces of case hardening turned silver. Hammer has a slightly damaged nose with moderate to heavy pitting. Trigger guard & back strap retain most of their strong orig silver plating with brass showing through only on edges. Grip has a repaired left toe with minor nicks & scratches and retains traces of orig finish being a hand worn patina. Flask has a small dent on one side, otherwise is fine & retains a dark mustard patina overall. Mold has numerous small nicks & dings with clean cavities. Nipple wrench is fine. Case has light nicks & scratches with a scrape on one end of lid and retains a fine restored finish. Interior is moderately to heavily faded showing moderate wear but completely intact. 4-31597 JR601 (7,500-12,500)

CASED COLT POCKET NAVY PERCUSSION REVOLVER. SN 3937. Cal. 36. Usual configuration with 5-1/2″ oct bbl, brass pin front sight and a 1-line “NEW-YORK U.S. AMERICA” address. It has 5-shot rebated cylinder with stagecoach holdup scene and all five safety pins are prominent. It has silver plated brass grip frame with 1-pc walnut grip. Accompanied by an orig walnut Colt casing with dark green velvet lining compartmented in bottom for another Colt revolver (a 6″ Colt 1849 pocket revolver fits perfectly), a blued “COLT’S PATENT” mold, a 2-sided flying eagle flask, an L-shaped nipple wrench and a lacquered tin of Eley’s caps. Corner compartment contains miscellaneous bullets & balls. CONDITION: Good, all matching, rammer handle is properly unnumbered. No orig finish remains being a cleaned metal color with light to moderate pitting on bbl & front of cylinder. Cylinder retains 40-50% stagecoach holdup scene and grip frame retains traces of orig silver plating, being mostly a medium mustard patina. Grip is sound with minor nicks & scratches and retains about 90% strong orig varnish. Mechanics are crisp, strong bore with moderate pitting. Case is fine with a short grain check in lid which has also been lightly sanded with a heavy scrape removed. Interior has a small tear inside lid with bottom soiled & faded with wear from front sight. One partition has been cut away to accommodate the larger rammer pivot of the pocket Navy. 4-32858 JR182 (2,500-3,500)

CASED COLT MODEL 1849 PERCUSSION POCKET REVOLVER. SN 124836. Cal. 31. Civil War Era Colt pocket with 5″ oct bbl, pin front sight, 2-line “NEW YORK CITY” address with serifs. It has 5-shot cylinder with stagecoach holdup scene and silver plated brass grip frame with 1-pc walnut grip. Accompanied by an orig Colt mahogany casing for this bbl length revolver with faded red velvet lining compartmented in bottom for the revolver, a Colt’s Patent brass mold and dbl sided eagle flask with a paper container of caps, a spare nipple, a spare flask spout and orig key attached to an old German silver medallion with an engraved eagle stamped “W.S. BEECHER, / NEW HAVEN, / CONN. / 1876.” CONDITION: Fine, all matching including wedge. Cylinder pin has been lightly filed but serial number is partially visible. Bbl retains 30-40% orig blue, mostly flaked to a medium patina. Rammer pivot retains strong case colors. Cylinder is mostly a gray/brown patina with a series of dents in one small area and retains 70-75% stagecoach holdup scene. Three of five safety pins are prominent. Frame retains 50-60% faded case colors with balance turned silver and a few spots of pitting. Grip frame retains most of its orig strong silver plating. Grip is sound showing light wear with a few light handling & use marks and retains most of its strong orig factory varnish. Mechanics are crisp, bright shiny bore with a few small spots of light pitting. Case has a grain check in lid and another in bottom, otherwise is sound with nicks & scratches and a small gouge and retains most of its orig factory varnish. Interior is much faded and slightly loose & shrunk in lid showing moderate to heavy wear in bottom. Mold is fine and flask retains about 80% orig finish. Altogether a fine orig set. 4-59724 JR184 (3,500-5,500)

TWO COLT MODEL 1849 POCKET REVOLVERS IN A CASE WITH ACCESSOREIS. SN 72088 & 72432. Cal. 31. Nearly identical 49 Pockets with 5″ oct bbls, 2-line “NEW YORK CITY” address with serifs. Both have 5-shot cylinders with stagecoach holdup scene and brass grip frames and 1-pc walnut grips. Accompanied by a dbl casing made from a mahogany hinged lid box, probably an old silverware box that measures 11-1/4″ x 10″ that has been lined with brown felt and compartmented in bottom for both revolvers, a dbl sided eagle flask and a smooth bag flask with two blued 2-cavity molds, one of which is marked “31 PKT”. Corner compartments contain cap tins. Backstraps of both revolvers are inscribed “HCM” which appears to have been done with a pantograph. CONDITION: Serial #72088 is fine to very fine, all matching including wedge which is possibly a renumbered blank. Bbl retains about 95% strong orig blue and rammer handle most of its orig case colors faded on handle, bright on pivot. Cylinder retains 80-85% strong orig blue and about 95-96% stagecoach holdup scene. All five safety pins are prominent. Frame retains strong dark case colors, less faded on left side. Grip frame retains traces of orig silver plating with backstrap an artificially aged patina. Grip is sound with light handling & use marks and retains a worn smooth patina. Mechanics are fine, bright shiny bore with a scattered few spots of light pitting. Serial #72432 is good to very good, all matching including wedge. No orig finish remains being an artificially aged dark blue/brown patina with fine pitting on bbl, slightly heavier on left side of frame & hammer. Grip frame is a medium mustard patina with artificially aged backstrap. Grip is sound with light handling & use marks and a chipped left toe with wear on edges and retains 75-80% orig varnish. Mechanics are fine, worn dark bore. Case is fine with a couple of loose corners, light handling & use marks and retains most of a restored finish. 4-31596 JR186 (2,500-4,000)

COLT MODEL 1849 POCKET REVOLVER. SN 322587. Cal. 31. Usual configuration with 6″ oct bbl, brass pin front sight and 1-line New York U.S. America address. It has 5-shot cylinder with “COLT’S PATENT” on left side of frame & brass grip frame with 1-pc walnut grip. CONDITION: Fine, all matching except rammer which is properly unnumbered. Bbl retains 60-70% thin orig blue, strong on bottom three flats with some fine pitting around muzzle. Rammer retains faded case colors on pivot. Cylinder retains traces of orig blue with about 75-80% stagecoach holdup scene with some fine pitting around front edge. Frame retains 75-80% orig case colors, bright on right side, a little more faded on left side and on recoil shields. Hammer retains strong case colors on sides & back edge. Trigger guard & backstrap are a mellow brass patina. Grip has a couple of dings on left bottom edge and another on right and retains 80-85% orig varnish. Mechanics are fine, strong bright bore with scattered fine pitting. 4-59729 JR409 (2,500-3,500)

INSCRIBED COLT MODEL 1849 PERCUSSION POCKET REVOLVER SN 69585. Cal. 31. Fine pocket Colt with 4” oct bbl, brass pin front sight and 2-line New York City address with serifs at each end. Left flat of bbl lug is engraved in beautiful period script & block letters “G.W. Babcock Jr / Providence R.I.” It has 5-shot cylinder with “COLTS PATENT” on left side of frame and silver plated grip frame with 1-pc walnut grip. Accompanied by a large packet of, primarily pension papers, of Mr. Babcock, which indicates he served in the 4th & 7th Rhode Island Volunteer Infantry from May 1862 to June 1865, apparently mustering out as a private. Mr. Babcock was born 18 June 1841 in Providence, RI and died 18 June 1914. CONDITION: Good. No orig finish remains on iron, being a mottled silver/brown patina with spots of moderate pitting on bbl. Cylinder has spots of lighter pitting and retains about 70% stagecoach holdup scene. Frame & hammer are also mottled silver/brown patina. Trigger guard & back strap retains about 75% strong orig silver. Grip is sound with slightly worn edges, light nicks & dings and retains most of its orig varnish. Mechanics are fine, strong bright bore with moderate pitting. 4-32719 JR596 (3,500-4,500)

COLT MODEL 1849 PERCUSSION POCKET REVOLVER. SN 108353. Cal. 31. Usual configuration with 4″ oct bbl, pin front sight and 2-line New York City address with serifs at each end. It has 5-shot cylinder with faint “COLT’S PATENT” on left side of frame. It has silver plated brass trigger guard & backstrap with 1-pc walnut grip. PROVENANCE: Glenn Marsh Collection. CONDITION: Very good, all matching including wedge. No orig finish remains on iron being a medium silver/brown patina with some light chemical streaking on bbl. Cylinder retains 60-70% stagecoach holdup scene with all five safety pins strong. Trigger guard retains 40-50% orig silver plating with backstrap a mellow brass patina with light silver on buttstrap. Grip is sound with light edge wear and a few nicks and retains 90-95% strong orig varnish. Mechanics are fine, strong bore with light fine pitting. 4-59615 JR410 (750-1,250)

COLT MODEL 1849 PERCUSSION POCKET REVOLVER. SN 284816. Cal. 31. Usual configuration with 4″ oct bbl, brass pin front sight with 1-line New York U.S. America address. It has 6-shot cylinder with brass trigger guard & backstrap and 1-pc walnut grip. PROVENANCE: Glenn Marsh Collection. CONDITION: Very good, all matching including wedge except rammer which is properly unnumbered. Bbl retains 30-40% blue mixed with mottled silver/brown patina with some scattered fine pitting & hammer marks over wedge slot. Cylinder is a mottled gray/brown patina and retains 25-30% stagecoach holdup scene. Frame has a dark finish that appears to have been dipped in a bluing tank. Trigger guard & backstrap retain traces of silver plating being a wonderful medium mustard patina. Grip has a repaired, chipped toe with a gouge on right side and some battering on bottom with light wear and retains most of its orig varnish. Mechanics are fine, strong bright bore with scattered moderate pitting. 4-59617 JR411 (750-1,250)

COLT MODEL 1862 POLICE PERCUSSION REVOLVER. SN 8624. Cal. 36. Usual configuration with 4-1/2″ rnd bbl, Model 1860 Army-style creeping rammer with 5-shot fluted cylinder and silver-plated brass trigger guard & backstrap with 1-pc walnut grip. CONDITION: Fine, all matching including wedge. Bbl & rammer retain traces of orig finish in sheltered areas being mostly a blue/gray patina with fine pinpoint pitting. Cylinder is a gray metal color with traces of blue in flutes and three of five safety pins strong. Frame retains about 90% orig case colors, strong & bright on right side, a little more faded on left side. Hammer retains strong case colors on sides & back. Trigger guard & backstrap retain about 60-70% silver plating with exposed areas a light mustard patina. Grip is sound showing light to moderate wear and retains about 75% orig varnish. Mechanics are fine, dark worn bore. 4-59731 JR413 (750-1,250)

RARE ENGRAVED AGENT MARKED WHITNEY NEW MODEL PERCUSSION POCKET REVOLVER SN 315. Cal. 28. Unusual little pocket revolver, very closely resembling a Colt Model 1855 Root, with which it was made to complete. It has 3-1/2” oct bbl with brass pin front sight and maker’s name & address on top flat. It has 2-pc rammer and 6-shot unfluted cylinder with roll engraved eagle, shield & lion motif. Frame & bbl lug are lightly engraved with well-executed foliate arabesque patterns with feather patterns over top strap. Back strap is engraved “J. HAPGOOD AGENT, BOSTON”. It has 2-pc smooth walnut grips numbered to this revolver. Only about 2,000 of these little revolvers were made in period 1860-67. This one, being an early production piece, would have made it available for Civil War service. CONDITION: Fair to good. No orig finish remains being a cleaned gray metal color with light to moderate pitting. Cylinder retains traces of orig cylinder scene. Rammer retainer screw is stripped. Grips have chipped toes with battered bottom edges and retain most of a restored finish. Mechanics are fine, strong bore. 4-32675 JR504 (1,000-2,000)

COLT MODEL 5A 1855 ROOT SIDE HAMMER PERCUSSION REVOLVER SN 6006. Cal. 31. Blue finish with 4-1/2” rnd bbl, brass pin front sight with usual New York address. It has 5-shot full fluted cylinder and 1-pc walnut grip. Cylinder pin also has a patent date. CONDITION: Fine. Overall retains 65-75% glossy orig blue with loss areas flaked, not worn, to light patina. There are wrench marks on either side of muzzle. Rammer retains strong case colors on handle & pivot with bright case colors on inside of hammer, faded to silver on outside. Grip is sound with light edge wear and a few chips in varnish on right side. Mechanics are fine, strong bright bore with scattered spots of pitting. 4-59733(2,000-3,000)

COLT 1855 MODEL 5 ROOT SIDEHAMMER PERCUSSION REVOLVER. SN 3090. Cal. 31. Blue finish with 3-1/2” rnd bbl, pin front sight with New York address. It has a 5-shot fluted cylinder with 1-pc ivory grip. CONDITION: Very good to fine, all matching. Bbl retains 25-30% flaked orig blue with balance flaked to a medium patina with wrench marks about center point. Frame retains about 60% orig blue, glossy & strong in sheltered areas, flaked & worn to a medium patina elsewhere. Cylinder retains about 50% orig blue, mostly in flutes. Grip has a repaired chip in toe, exhibits shrinking with several age lines and retains a light mellow patina. Mechanics are fine, strong bore with light to moderate pitting. 4-59623 WD453 (500-1,000)

MANHATTAN SERIES 3 PERCUSSION POCKET REVOLVER. SN 28628. Cal. 36. Usual configuration with 4″ oct bbl, German silver half-moon front sight with 1-line Newark address. It has 5-shot cylinder with 5-panel cylinder scene and it has silver-plated trigger guard & backstrap with 1-pc walnut grip. PROVENANCE: Glenn Marsh Collection. CONDITION: Fine, all matching except cylinder which has the last four digits of “8728” while last four digits of serial number are “8628”. Bbl retains a thin blue patina with strong blue on bottom three flats. Rammer pivot retains dark case colors. Cylinder is a gray/brown patina with some scattered light pitting with most of cylinder scene panels fine. Frame is a silver/gray patina with trigger guard retaining about 50% silver with balance & backstrap a mellow brass patina. Grip is sound with moderate wear and retains about 85% orig varnish. Mechanics are fine, worn dark bore. 4-59635 JR412 (750-1,250)

UNUSUAL UNMARKED EARLY PERCUSSION REVOLVER SN NSN. Cal. About 36. Made by an unknown maker with 5-1/8” oct to rnd bbl resembling a small dragoon bbl with deep 7-groove, straight rifling. It has a 2-pc Colt style rammer with an unusual bayonet type latch & stud just below muzzle. Wedge enters from right side with screw below. It has a 6-shot straight cylinder with deep protected nipple wells and rnd cylinder stop slots with short leads. Frame is flat sided with heavy recoil shields having a sgl bbl/frame pin and hammer with a long spur & a curl at end. Trigger guard base & front strap are 1-pc held with three screws and trigger guard is stamped metal screwed to bottom. It has a hump-back 1-pc back strap & butt strap screwed to back of frame and joined at front strap. It has a hump-back 2-pc smooth dark walnut grip with flared butt. CONDITION: Good. Bbl & rammer retain an overall smooth plum brown patina with a few light nicks & dings on bbl lug. Cylinder is a thin gray/brown patina with one small area of dings. Trigger guard & grip frame retain dark blue finish with fine surface rust. Receiver retains traces of blue in sheltered areas with balance a silver/brown patina with light surface pitting. Mechanics are fine, strong sharp bore, dark in grooves. 4-32681 JR497 (1,000-2,000)

RARE E.A. PRESCOTT POCKET MODEL PERCUSSION REVOLVER SN 11. Cal. 31. Very rare American percussion revolver with only about 100 produced in period 1860-61. It has 4-1/4” oct bbl with half moon German silver front sight with rare bbl marking “E.A. PRESCOTT WORCESTER MASS / PAT’D. OCT. 2. 1860”. Apparently only a few of these had markings anywhere except serial number. It has an unfluted 6-shot cylinder with Remington-style star wheel on back. It has thin cylinder stop slots. It has a cast brass frame with spur trigger and knurled high spur hammer with a complicated U-shaped hammer spring. It apparently was silver plated originally, now with only traces of silver under grips. Serial number was observed on bottom of bbl and left side of butt strap under grip, on face of cylinder, on rammer lever, rammer & rammer lock. Grips are also numbered on inside. CONDITION: Very good. Bbl retains a dark patina with fine pitting on right side. Frame is a dark mustard patina and cylinder retains most of a restored blue finish with two areas of fine pitting. Right grip has a repair at top and is missing a sliver at heel with both grips retaining about 50% orig varnish. Hammer is not firm in safety notch, otherwise mechanics are fine, strong dark bore with moderate to heavy pitting. 4-32674 JR502 (1,500-2,500)

ALLEN & WHEELOCK SIDEHAMMER NAVY REVOLVER SN 201. Cal. 36. Standard model with about 750 made in period 1858-1861. It has 5” oct bbl with dovetailed German silver front sight with 5-shot cylinder and hammer mounted to right side of frame. Rammer lever is also the front half of trigger guard and is retained by a spring loaded catch at back of trigger guard. It has 2-pc walnut grips. CONDITION: Good to very good, all matching including grips. No orig finish remains being a cleaned light gray/brown patina with scattered spots of rust. Bbl markings are completely worn away. Cylinder retains about 75% stag & dog hunting scene. Grips show moderate to heavy wear on edges and retain 75-80% orig varnish. Mechanics are a little tight but fine, strong bright bore with scattered very fine pitting. 4-31551 JR604 (500-1,000)

VERY UNUSUAL EXPERIMENTAL OR PROTOTYPE BENCH MODEL PERCUSSION REVOLVER SN NSN. Cal. About 38. Most unusual & unique revolver, probably built during the great American firearms explosion of ideas in the mid-19th century. It has 6-7/8” oct bbl with an unusual turned brass fitting over muzzle and 6-groove straight rifling. Top of bbl has a brass rod which extends through a bracket that has two tiny dovetails in top flat. The rear end of rod is fitted with a fixed V-groove sight along with an articulated peep sight. It has a tiny 2-pc ramrod pinned into the bbl lug with a tension spring dovetailed into bottom flat. Rammer handle is octagonal and tapered to larger front end. It has 6-shot unfluted cylinder with protruding nipples and a curious shield in frame reminiscent of pepperbox nipple shields or the Richards conversion rings on Colt conversion revolvers. It has a ring trigger and is dbl action only. Grip is long & curved with brass panels, internally mounted, with an 8-pointed geometric star at top on each side and a most unique design on bottom with a small trap door cover on each side. It is completely unmarked although disassembly was not affected to determine hidden markings. CONDITION: Very good, missing wedge. All metal retains a strong plum/brown patina with a few scattered spots of light rust. Brass is a medium to dark mustard patina. Mechanics are fine, strong bore with scattered pitting. 4-32678 JR503 (500-1,000)

REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 93297. Cal. 44. Usual configuration with 8″ oct bbl, normal 3-line markings with pinch post front sight & grooved topstrap rear sight. It has brass trigger guard and 2-pc walnut grips with crisp cartouche on left side with matching pencil number inside. There are small inspector initials on various parts. These revolvers were well received and heavily used during Civil War and afterward in Indian Wars by a variety of cavalry units. After they became obsolete they were then sold privately and their use continued on frontier. Rarely are they ever found in unused condition. PROVENANCE: Glenn Marsh Collection. CONDITION: Extremely fine plus. Appears to be new & unfired retaining almost all of its fine glossy orig factory blue with a few scattered flaked spots that have turned to light patina. Hammer retains about all of its bright orig case colors and trigger guard is a medium to dark brass patina. Grips are crisp with a couple of minor chips and retain virtually all of their orig factory finish. Mechanics are crisp, brilliant shiny bore. 4-59631 JR393 (3,000-5,000)

OUTSTANDING MARTIALLY MARKED REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 69765. Cal. 44. Usual configuration with 8″ oct bbl, pinched post front sight with usual bbl markings. It has a brass trigger guard and 2-pc walnut grips with sharp, clear cartouche on left side and are pencil numbered to revolver. There are small inspector initials on various parts. These Remington revolvers were well favored by the Union during the Civil War and afterward with the Cavalry on the frontier. A trooper could carry one or two spare cylinders and reload very quickly vs. slow reloading of Colt percussion revolvers. Therefore they were in use more for longer periods of time and are rarely found in good condition. CONDITION: Extremely fine plus. Overall retains 95-97% strong, glossy, orig blue with slight muzzle & sharp edge wear with some light thinning on grip straps. Web of rammer handle has flaked to a dull blue patina. Trigger guard is a fine medium mustard patina & cylinder retains about 90% strong orig blue. Grips are as new with faint edge wear and retain virtually all of their orig factory varnish. Mechanics are crisp, strong bright bore with scattered moderate pitting. 4-33316 JR349 (4,000-6,000)

RARE REMINGTON BEALS ARMY PERCUSSION REVOLVER. SN 1614. Cal. 44. Usual configuration with 8″ oct bbl, standard markings on top flat & a dovetailed German silver cone front sight. It has brass trigger guard and 2-pc walnut grips with outline of a cartouche on left side and a partially legible “WAT” cartouche on right side. It has small “HH” and “W” inspector marks on various parts making it a very rare item indeed, as only about 750 passed U.S. inspection. CONDITION: Very good. Bbl retains 40-50% thin orig blue, strong in sheltered areas. Frame & grip frame are a gray patina as is cylinder which has a few spots of fine pitting. Left grip has a chipped toe and a small replaced sliver at heel, otherwise grips are sound with a dark, hand worn patina. Mechanics are fine, strong bright bore with scattered light pitting. 4-32824 JR387 (5,000-8,000)

REMINGTON MODEL 1861 OLD MODEL ARMY PERCUSSION REVOLVER. SN 2861. Cal. 44. Scarce Remington with 8″ oct bbl, usual 2-line marking with dovetailed German silver cone front sight & grooved topstrap rear sight. Rammer has grooved top edge with a filister screw in channel to prevent cylinder pin from moving during shooting. It has concealed threads in frame. There is a large “C48” stamped upside down on right side of frame. It has brass trigger guard & smooth 2-pc walnut grips whose numbers could not be found although it is readily apparent that they have been in place for life of revolver. Only about 6,000 of these were made in 1862. According to Flayderman’s Guide to Antique American Firearms just about entire production was purchased by military. Although grips do not show cartouche, there are small inspector initials on various parts. CONDITION: Very fine, all matching except grips as noted above. Bbl retains 60-70% thin orig blue, strong & bright on bottom. Frame, cylinder & grip frame are a smooth even blue/gray patina with traces of orig finish in most sheltered areas. Frame has a few scattered spots of very fine pitting. Grips are sound with minor nicks and retain a hand worn patina with traces of orig finish on right side. Mechanics are fine, bright shiny bore with a few spots of pitting. 4-31569 JR390 (2,500-4,000)

REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 81821. Cal. 44. Usual configuration with 8″ oct bbl, pinched post front sight with normal bbl markings & a strange plug on top flat at frame. It has brass trigger guard and 2-pc walnut grips that are beautifully carved with diamond patterns and a star around left escutcheon. Grips have small silver pins in some diamonds and points of the star. Several of the parts have inspector initials. PROVENANCE: Glenn Marsh Collection. CONDITION: Good to very good. Traces of orig finish remain in sheltered areas, being mostly a light to medium blue/brown patina. Front sight has been slightly altered and rammer latch stud may be an old replacement. Right grip has a pressure crack inside, otherwise they are fine and retain a dark hand worn patina. Mechanics are fine, bright shiny bore with a few scattered spots of light pitting. 4-59621 JR383 (500-1,000)

MARTIALLY MARKED REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 99770. Cal. 44. Standard New Model Army with 8″ oct bbl, pinched post front sight and 3-line bbl markings. It has brass trigger guard and 2-pc walnut grips with clear “OWA” cartouche on left side. There are small inspector initials on most of parts. PROVENANCE: Glenn Marsh Collection. CONDITION: Fine, all matching including grips. Bbl retains traces of orig finish being mostly a light silver/brown patina. Frame retains 15-20% orig blue with balance a light patina. Grip frame is also a light patina. Cylinder retains traces of orig blue with balance a light patina. Most of loss areas are flaked, rather than worn. Mechanics are fine, bright shiny bore with scattered fine pitting. 4-59624 JR400 (1,000-1,500)

MARTIALLY MARKED REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 51023. Cal. 44. Fine martial New Model with 8″ oct bbl, usual 3-line bbl marking with dovetail German silver cone front sight & grooved top strap rear sight. It has brass trigger guard & 2-pc walnut grips with clear cartouche on left side. There are small inspector initials on various parts. CONDITION: Very good to fine, all matching except grips whose number could not be found. It is apparent however that they have been in place for life of revolver. Bbl & rammer handle retain thin orig blue mixed with medium patina, stronger on rammer handle. Frame retains 20-25% thin orig blue with balance a gray patina. Cylinder & grip straps are a gray patina. Grips have a chipped left heel & show moderate to heavy wear with traces of orig finish. Mechanics are fine, bright shiny bore with scattered pitting. 4-31568 JR391 (1,500-2,500)

REMINGTON NEW MODEL ARMY PERCUSSION REVOLVER. SN 101913. Cal. 44. Usual configuration with 8″ oct bbl, added brass target front sight over the orig pinched post front sight. It has usual bbl markings with brass trigger guard and 2-pc walnut grips with a mostly legible “OWA” cartouche on left side. There are inspector initials on various parts. Accompanied by a Lawrence basketweave tooled chamois lined single loop holster with buckstitch laced edge. PROVENANCE: Glenn Marsh Collection. CONDITION: Good. No orig finish remains being a chocolate brown attic patina overall with some traces that may be an old nickel finish. Grips have a chipped left toe & show heavy wear. Mechanics are a little loose but functional, strong sharp bore with moderate pitting. Holster is fine. 4-59616 JR401 (400-700)

VERY RARE REMINGTON BEALS NAVY PERCUSSION REVOLVER. SN 63. Cal. 36. Very rare early production Beals Navy with 7-1/2″ oct bbl, dovetail German silver cone front sight & usual 2-line bbl address. It has single wing cylinder pin with about 1″ rod extension which fits into a slot in rammer handle. It has brass trigger guard & 2-pc walnut grips. Flayderman’s Guide to Antique American Firearms states that only about 200 of these very rare revolvers were made, apparently in first year of production. Buttstrap has small white painted “KM676” indicating that this at one time was part of the famous Karl Muldenhauer Collection. PROVENANCE: Karl Muldenhauer Collection CONDITION: Very good, all matching including rammer, no number could be found on cylinder. No orig finish remains, being a light gray/brown patina with some scattered fine pitting. The small pin in cylinder pin is probably a replacement. Head of cylinder pin shows some welded repairs. Grips also appear to be replacements and retain most of a restored finish. Mechanics are fine, very bright shiny bore with a few scattered spots of pitting. 4-33337 JR369 (4,000-7,000)

REMINGTON MODEL 1861 OLD MODEL NAVY PERCUSSION REVOLVER. SN 21572. Cal. 36. Usual configuration with 7-3/8″ oct bbl, dovetail German silver cone front sight with grooved top strap rear sight. It has slot in rammer handle and brass trigger guard with 2-pc walnut grips numbered to this revolver. There is a small “B” inspector mark on left side of bbl & frame with another on cylinder. Only about 7,000 of these revolvers were made in 1862, most of which were purchased by U.S. Government. CONDITION: Very good, all matching including cylinder & grips. No orig finish remains except thin blue/brown on cylinder with balance a mottled gray/brown patina on bbl and a smooth medium patina on frame. Grips are sound with minor nicks & scratches and retain most of their orig finish with moderate edge wear. Mechanics are sound, bright shiny bore with scattered pitting. 4-31570 JR386 (1,500-2,500)

MARTIALLY MARKED STARR DA NAVY PERCUSSION REVOLVER. SN 1191. Cal. 36. Scarce Navy with 6″ rnd bbl, usual markings on frame with 1-pc walnut grip having a cartouche on left side and small inspector initials on various parts. Grip has number “1494” at top edge on both sides. Only about 3,000 of these scarce revolvers were made in period 1858-60 with government purchasing about 2,250 of them. These revolvers are seldom encountered with martial markings. CONDITION: Fine, all matching. Bbl & cylinder retain a smooth gray/brown patina but appears to be nearly unfired. Frame retains 75-80% glossy orig blue with loss areas flaked, not worn, to a light patina. Grip has a chip in toe with some bruises & a gouge and light handling & use nicks & scratches and retains about 75-80% orig finish. Mechanics are crisp, bright shiny bore. 4-33344 JR370 (3,000-5,000)

STARR DA ARMY PERCUSSION REVOLVER. SN 9102. Cal. 44. Fine Civil War era revolver with 6″ rnd bbl, dovetail front sight with blue finish and 1-pc walnut grip that has clear cartouches on both sides. There are small inspector initials on various parts. These revolvers were prolific throughout the Civil War with 20,000 plus having been produced. They saw extensive service and were well favored with Union troops. These are rarely found with high condition. CONDITION: Very fine poss. unfired. Bbl retains 93-95% glossy orig blue with flaked areas a medium to dark patina. Rammer retains most of its orig case colors, brilliant on pivot, dark elsewhere. Bbl lug & frame retain 40-50% glossy orig blue with balance flaked, not worn, to a medium patina. Hammer retains virtually all of its orig case colors, slightly muted. Cylinder retains 15-20% orig blue with balance flaked to medium patina and one spot of light pitting. Grip is sound with light nicks & scratches and retains most of its orig oil finish. Mechanics are crisp, very bright shiny bore. 4-31574 JR382 (2,500-5,000)

SCARCE FREEMAN ARMY MODEL PERCUSSION REVOLVER. SN 594. Cal. 44. Rare Civil War era revolver with only about 2,000 having been produced in period 1863-64. According to Flayderman’s Guide to Antique American Firearms although there are no known military contracts, these revolvers are considered secondary martial arms and may have been acquired by some states. It has 7-1/2″ stepped round bbl with tiny iron front sight and grooved top strap rear sight with 6-shot unfluted cylinder with concealed nipples and 2-pc rammer with Colt-style horizontal latch. It has 4-screw frame with 2-pc walnut grips numbered to this revolver. The Freeman is unique with its easily removed cylinder which made for easy loading & cylinder changes. PROVENANCE: Glenn Marsh Collection. CONDITION: Fine to very fine, all matching including grips. Bbl & cylinder retain most of their orig strong case colors with edge wear and a drag line on cylinder which also has a few light scratches and some light surface rust. Frame retains 30-40% flaked blue, strong in sheltered areas with flaked areas a light patina. Grip straps are a blue/gray patina. Grips have small chips on edges with a couple of bruises and retain a worn bright patina. Mechanics are fine, bright shiny bore with scattered pitting. 4-59632 JR405 (1,500-3,000)

RARE FREEMAN ARMY PERCUSSION REVOLVER. SN 753. Cal. 44. Rare Civil War era revolver with only about 2,000 having been produced in period 1863-64. According to Flayderman’s Guide to Antique American Firearms although there are no known military contracts, these revolvers are considered secondary martial arms and may have been acquired by some states. It has 7-1/2″ stepped round bbl with tiny iron front sight and grooved topstrap rear sight with 6-shot unfluted cylinder with concealed nipples and 2-pc rammer with Colt-style horizontal latch. It has 4-screw frame with 2-pc walnut grips numbered to this revolver. The Freeman is unique with its easily removed cylinder which made for easy loading & cylinder changes which brings up point that bbl, rammer, trigger guard, frame & grips are numbered “753” while cylinder & cylinder pin are numbered “752” – most likely a unit mix-up. PROVENANCE: Glenn Marsh Collection CONDITION: Very fine, numbers as noted above. Overall retains 85-90% strong orig blue with balance flaked, not worn, with exposed areas a medium to dark patina. Mechanics are fine, strong bore with scattered pitting. 4-59636 JR394 (3,000-5,000)

SCARCE JOSLYN NAVY PERCUSSION REVOLVER. SN 1109. Cal. 44. Very rare martial revolver with 7-7/8″ oct bbl, dovetail front sight with 2-line bbl marking and with a 3-pc rammer. It has an unusual side hammer with cylinder pin inserted through rear like the 1855 Colts. It also has coarse checkered 2-pc walnut grips. This is one of only 100 of these revolvers purchased by the Navy in Oct. 1861. There was a total of 1,000 more purchased on open market through a New York dealer through April 1862. This one has a small anchor on bottom flat of bbl by serial number. CONDITION: Good to very good. Bbl retains about 65-70% thin blue mixed with light patina. Frame, cylinder & grip frame are a cleaned gray patina with a few small spots of light pitting. Grips are sound showing moderate wear with a gouge on right side and retain a dark hand worn patina. Mechanics are fine, bright shiny bore. 4-33345 JR371 (4,000-6,000)

SCARCE ALLEN & WHEELOCK CENTER HAMMER ARMY PERCUSSION REVOLVER. SN 131. Cal. 44. Unusual but practical, this revolver has a 7-1/2″ oct to rnd bbl with unfluted 6-shot cylinder and 2-pc walnut grips numbered to this revolver. It has an unusual captive rammer with lever being front half of trigger guard secured with a latch from rear end. Cylinder pin is retained by a simple bayonet latch. According to Flayderman’s Guide to Antique American Firearms only about 700 of these revolvers were made in period 1861-62 with the government purchasing 536 of what is assumed to be this model. CONDITION: Fine, all matching. Overall it retains blue in most sheltered areas with rammer handle/trigger guard dark blue with balance of metal a smooth, even medium brown patina with some cleaning on round portion of bbl. Grips are sound with nicks & dings and retains most of their orig varnish. Mechanics are fine, bright shiny bore. 4-31572 JR404 (2,500-5,000)

ROGERS & SPENCER PERCUSSION REVOLVER. SN 2696. Cal. 44. Blue finish with 7-1/2″ oct bbl, German silver cone front sight with to strap groove rear sight & usual markings with crisp cartouche on left grip and small inspector initials on various parts. It has 2-pc flared butt walnut grips with a 3-pc rammer. CONDITION: Very fine, all matching. Bbl & cylinder retain 30-40% orig blue with balance flaked, not worn, to a medium dark patina. Frame retains 88-90% glossy orig blue with a few flaked spots turned to dark patina. Right grip is missing several chips with one chip from left grip and overall retains most of its orig finish. Mechanics are crisp, brilliant shiny bore, probably unfired. 4-31485 JR396 (2,000-3,000)

ROGERS & SPENCER ARMY PERCUSSION REVOLVER. SN 3133. Cal. 44. Blue finish with 7-1/2″ oct bbl, usual markings on top strap with crisp inspector cartouche on left grip and small inspector marks on various parts. CONDITION: Very fine, all matching including rammer & grips, probably unfired. Overall retains 70-75% glossy orig blue with flaked areas flaked, not worn, to a medium patina. Rammer, handle & hammer retain dark case colors. Grips have minor chips on flared edges and retain most of their orig varnish. Mechanics are crisp, brilliant shiny bore. 4-31575 JR385 (2,500-4,000)

ROGERS & SPENCER PERCUSSION REVOLVER. SN 827. Cal. 44. Usual configuration with 7-1/2″ oct bbl, partridge target style front sight with slightly altered groove in top-strap rear sight. It has 3-pc rammer with flared butt 2-pc grips. PROVENANCE: Glenn Marsh Collection CONDITION: Good to very good, all matching. Bbl & cylinder retain 88-90% glossy orig blue. Frame is mostly a medium brown patina with scattered flakes of orig blue. Grips are missing a sliver at right heel with chips on flared edges with a clear cartouche on left side and retain most of their orig finish. Mechanics are crisp, brilliant shiny bore. Consignor states he used this revolver for black powder target shooting. 4-59628 JR395 (750-1,250)

WHITNEY NAVY NAVY PERCUSSION REVOLVER. SN 25612. Cal. 36. Second model, 4th type with 7-5/8″ oct bbl, tall brass pin front sight with usual markings on top flat and an anchor at frame. Bottom of bbl, back of cylinder & left side of frame have small “O” inspector marks and there are large “GG” and “P” inspector marks on face of cylinder. It has brass trigger guard and 2-pc walnut grips. Rammer latch is horizontal Colt type. CONDITION: Fine, all matching including rammer, cylinder & grips. Overall retains a thin blue/brown patina with about 50% thin blue on bbl. Cylinder is a gray patina. Grips are sound with slightly chipped toes and retain a hand worn patina. Mechanics are fine, strong bore with scattered pitting. Period repair to loading lever latch. 4-31571 JR398 (1,500-2,500)

RARE WHITNEY NAVY CONVERSION REVOLVER. SN 27739. Cal. 38 RF. Usual configuration with 7-5/8″ oct bbl, brass pin front sight with Whitney name & address on top flat & a small anchor at frame. It has a horizontal rammer latch, missing its stud. It has 6-shot cylinder that has had rear end machined away with a 5/16″ thick ring fitted with rebated chambers. Front is stamped with a large “55” assembly number which number also appears on bottom flat of bbl. Frame has a loading groove cut in right side and has a recoil plate inside cylinder cutout that is screwed in place. It has brass trigger guard with 2-pc walnut grips numbered to this revolver. PROVENANCE: Glenn Marsh Collection. CONDITION: Good to very good, all matching. Bbl retains 25-30% dull, thin orig nickel with balance of metal a very dark brown attic patina. Hammer spur is broken. Grips are sound and retain traces of orig finish under an old refinish. Mechanics are difficult with broken hammer spur but seem to function well. It has bright shiny bore. 4-59622 JR407 (500-1,000)

SPECTACULAR CASED MASS ARMS BELT REVOLVER. SN 84. Cal. 31. This wonderful revolver appears new & unfired. It has 5″ rnd bbl, 6-shot etch-engraved cylinder with hand engraved frame with about 50% coverage fine foliate arabesque patterns which extend down lockplate and on hammer. It has the Maynard tape priming system with a beautifully engraved compartment cover with a spread-winged American eagle and Maynard’s patent information. It has usual Mass Arms markings on top strap & 2-pc checkered walnut grips. Accompanied by its orig walnut casing with blue velvet lining with “HITCHCOCK & CO” distributor’s label inside lid and compartmented in bottom for revolver, a beautiful orig Mass Arms flask with company info on one side and a fine early American eagle on other. It also has an orig tin for rolls of primers containing three complete & one partial rolls of orig primers. Back edge has compartment for an orig 2-cavity brass mold, a brass rammer, L-shaped nipple wrench and orig functioning key along with a few lead balls. According to Flayderman’s Guide to Antique American Firearms there were only about 1,000 of these revolvers made in period 1851-57. This revolver is without the 1850 patent date on bbl. CONDITION: Exceptionally fine. Appears to be unfired retaining virtually all of its glossy orig blue on bbl, cylinder & trigger guard and about all of its brilliant case colors on frame, top strap, trigger, hammer & lockplate and about all of its orig silver on backstrap. Grips are equally new with no visible flaws, retaining virtually all of their orig varnish. Case is extremely fine with minor nicks & scratches retaining virtually all of its orig factory varnish. Interior is rich & dark with only very minor wear from revolver. Flask is equally new, retaining virtually all of its orig finish. Mold is also as new. A truly exceptional & rare set. 4-31526 JR183 (15,000-25,000)

EXTREMELY UNUSUAL SINGLE SHOT PERCUSSION TARGET PISTOL SN NSN. Cal. 36. Very unusual inventor’s model or simply a homemade target pistol with lightweight 6” oct bbl, brass blade front sight with a brass tube underneath containing a wooden ramrod. It has a rectangular shaped frame with fixed sight on top front edge with internal lock works & right side mounted hammer. It appears to have been designed as a pill lock with an unusual hexagonal cover for the thimble with built in firing pin. Trigger is formed & welded sheet metal screwed to bottom and it has replacement thick mahogany grips with flared front & rear edges. CONDITION: Very fine. Bbl is a bright metal color with some slight discoloration. Brass frame & ramrod tube are a medium mustard patina and grips are sound with a hand worn patina. Mechanics are fine, bright shiny bore. 4-32679 JR501 (500-1,000)

NAVY ARMS NEW MODEL NAVY REVOLVER. SN 9903. Cal. 36. Standard 7-1/2″ bbl. This is an Italian copy of an 1861 Colt Navy, six-shot black powder revolver with brass front sight and roll marked cylinder of a naval scene labeled “ENGAGED 16 MAY 1843”. Frame is cut and set-up to accept shoulder stock and also has capping groove in the loading area. Gun is accompanied with its original wood grain box and paperwork. PROVENANCE: Glenn Marsh Collection. CONDITION: Extremely fine. Appears unfired with nearly all its original finish and has areas of original dry packing grease. 4-59641 BT97 (250-400)

RARE CIVIL WAR ENGRAVED & INSCRIBED SMITH & WESSON NO. 2 ARMY REVOLVER. SN 14456. Cal. 32 RF. Usual configuration with 6″ oct bbl with integral rib and German silver front sight and 2-pc rosewood grips numbered to this revolver. Frame, cylinder & bbl are nicely engraved in period chiseled foliate arabesque patterns with punch dot background and a wave & dot pattern on each side of bbl. Backstrap is inscribed in period script “Col. John T. Wilder”. Both sides of receiver have an engraved lightning bolt representing Col. Wilder’s “Lightning Brigade”. Col. Wilder enlisted in the Indiana 17th Infantry as a Lt. Colonel on June 4, 1861 and resigned on Oct. 5, 1864 as a Brevette Brigadier General. He was born Jan. 31, 1830 and died Oct. 20, 1917. Col. Wilder’s unit participated in many skirmishes & battles throughout the Civil War, mostly in the South including TN, GA & AL. Major battles included Murfreesboro, Chickamauga, New Market, Shelbyville, Hoover’s Gap, Ringgold, Rock Springs, Cleveland, McMinnville, Dallas, New Hope Church, Noon Day Creek, Rome, Chattanooga, Ebenezer Church, Plantersville, Selma & Macon. CONDITION: Good to very good. Metal retains a dark plum/brown patina with blue in some of very sheltered places. Grips are fine. Good mechanics, strong dark bore. 4-32717 JR177 (20,000-25,000)

SPECTACULAR CASED BRACE OF SMITH & WESSON NO. 2 ARMY SPUR TRIGGER REVOLVERS. SN 15240 & 48577. Cal. 32 RF. Revolvers are identical with blue finish, 6” keyhole bbls, half moon German silver front sight and 2-pc rosewood grips. They both have case colored hammer, trigger & ejector pin with unfluted 6-shot cylinders having normal patent dates. Serial #15240 certainly falls within the framework of the Civil War while #48577 was made substantially after the war. Accompanied by a spectacular orig Smith & Wesson rosewood casing with blank brass nameplate in lid, lined with rose colored velvet, compartmented in bottom for both pistols in center with bbl rests, otherwise a large open compartment. Left end has a rare 2-pc box of Union Metallic Cartridge Co. 32 RF Short cartridges with bright orange label. Corner compartments contain twenty loose 32 RF Long cartridges. This is an extremely rare casing with two outstanding revolvers. CONDITION: 4-32780 CONDITION: No. 15240 – Extremely fine, all matching including grips. Overall retains 96-97% strong glossy orig blue with only minor muzzle edge wear, a few small scrapes on bbl lug on left side of bbl lug in front of cylinder and some moderate thinning on back strap. Grips are extremely fine with light wear retaining most of their orig varnish. Mechanics are crisp, bright shiny bore with a few small spots of pitting. No. 48577 is also extremely fine and all matching. Overall retains 96-98% glossy orig blue with slight muzzle edge wear and a few small spots of rust on bottom three flats at muzzle. There are a couple of small scratches on left side of bbl. Grip frame is very strong. Hammer & ejector pin retain strong case colors with trigger turned gray. Grips are extremely fine with minor wear retaining about all of their orig varnish. Mechanics are crisp, brilliant shiny bore. Case has some minor raised grain in lid & a couple of grain checks in bottom, otherwise is extremely fine and retains about all of its orig factory varnish. Interior is moderately faded in bottom, strong & bright in lid showing light to moderate wear from revolvers with some chemical staining in right rear corner. Cartridge box is very fine with bright clear label. A truly wonderful set. 4-32780 JR627 (10,000-15,000)

CASED ENGRAVED SMITH & WESSON NO. 2 ARMY SPUR TRIGGER REVOLVER. SN 34056. Cal. 32 RF. Fine Nimschke-style engraved Army with 6” keyhole bbl, half moon front sight with rare 2-pc ivory grips, left side deep relief carved with a full bust figure of Robert E. Lee. Frame, bbl flats, top of bbl, top of back strap & heel are nicely engraved in foliate arabesque patterns with fine punch dot background. Front edge of cylinder is engraved to match and top strap has feather patterns with Nimschke’s traditional half diamond border patterns. Originally this revolver had full coverage gold wash. Accompanied by an extremely rare Smith & Wesson mahogany casing with rose colored velvet lining, compartmented in bottom in reverse configuration for revolver and a cartridge block containing seventy 32 cal rimfire rds. C CONDITION: Revolver is fine. Overall retains about 50% thin gold wash with trigger, hammer & cylinder lock retaining most of a restored blue finish. Front & back straps and bottom of frame are a medium gray/brown patina. Grips show heavy wear with a repaired crack in right side and numerous age lines and retain a golden mellow patina. Mechanics are fine, strong bright bore with moderate pitting. Case has a grain check in base and another in lid, otherwise is very fine with light nicks & scratches and retains most of its fine strong varnish. Interior is moderately to heavily faded, showing wear from revolver in the bottom. Cartridges are all fine with some oxidation on bullets. 4-32757(6,000-8,000)

WILLIAMSON POCKET DERRINGER SN 6939. Cal. 41 RF. Small convertible sgl shot derringer usable as either rimfire cartridge or, with special adaptor, as a muzzle loader, adaptor not present. It has a 2-1/2” ovoid shaped bbl with an arrow on top flat and a tiny German silver front sight. It has an engraved brass frame with brass trigger guard and 1-pc bird head walnut grip, checkered on butt. PROVENANCE: Glenn Marsh Collection CONDITION: Good. No orig finish remains with bbl a plum/brown patina and brass a very dark mustard patina. Grip is sound and retains about 85% orig varnish. Hammer does not have safety notch, otherwise mechanics are fine, strong bore with moderate pitting. 4-59634 JR590 (250-500)

RARE PATENT MODEL OR SALESMAN’S SAMPLE OF 1ST MOBILE STEAM-POWERED TANK. This unique model is of Winans Steam Gun. According some information provided by the consignor, this was invented by Charles S. Dickenson who manufactured in Baltimore, MD by Ross Winans in 1861 (he also built the first camel locomotive). Purportedly the gun could throw 200 balls a minute a distance of 2 miles. The steam engine and gun were protected by an iron cone all supported on a wheeled horse-drawn base. the gun was captured May 11, 1861 by Col. Jones and the 6th Mass. Regiment as Dickenson was attempting to move it south. Steam engine on this device purportedly actually works. SIZE: Approx. 28″l. CONDITION: Generally good. 4-31239 JJ16 (3,000-5,000)

IDENTIFIED SWORD AND SURGEON’S KITS OF DR. W. P. MAUZY. Included in this group is a 3-tier Civil War era George Tiemann surgeons kit. This kit contains over 25 tools most of which appear orig. Label inside for Tiemann is 63 Chatham, NY, which is Tiemann’s wartime address. Tools include capital amputation saw, trephine with 2 different sized blades, Rongeurs, etc. The smaller kit, also with Tiemann label, contains several small tools. The sword is not a regulation medical officer sword of the Civil War, however the sword does predate the war for manufacturer. The sword, probably imported by Horstmann, is ca. 1840. Accompanying this lot is a photograph of Dr. Mauzy’s home in Oakland, California after the war. CONDITION: Most tools in the large surgical kit are in fine condition exhibiting orig polish and shine. Smaller kit tools are worn. Sword is cleaned, scattered dents in decorated scabbard, blade is gray scattered pitting. 4-32605(4,500-6,500)

BEAUTIFUL CASED TREPHINING KIT, CIRCA 1845. A fabulous cased trephining kit. All tools in this kit are in fine condition exhibiting orig luster and finish. Trephines were used in brain surgery and the round blades of this tool would remove a circular piece of the skull to expose the brain. The rosewood case measures 8″x4″ and is about 2-1/2″ deep. In addition to the trephine is a bone brush, a scalpel and a Hays saw. Handles, which are ivory, are also in fine condition with only minor discoloration. Two of the tools in this kit are marked, both the scalpel and the bone file are marked by “E. Owens, Albany, NY. Owens is a known surgical tool maker in the pre-Civil War era. This is a rarely encountered ivory mounted surgical kit in beautiful condition. CONDITION: As described above. 4-32631 JS311 (2,500-3,500)

Revised: 10/19/2007

(Additional Information) Please note that the battle depicted here is between Union Maj. Gen. Alfred Pleasanton and Confederate Maj. Gen J. E. B. Stuart. Also note that the large, gesso, gold frame is a period frame, and further note that this was the largest cavalry battle of the Civil War.

(Correction)Re-lined. Various spattering of inpainting, some major-U.S.Flag and area just above. Also repair in area over U.S. Flag, wagon wheel.

EXTRAORDINARY MAMMOTH PANORAMIC OIL ON CANVAS CIVIL WAR BATTLE SCENE . This large painting was executed by Isaac F. Eaton and depicts the first main cavalry at Brandy station June 9, 1863. Eaton exhibited works in the Pennsylvania Academy of Fine Arts in 1879. The painting was given to the American Legion in Portland, ME where it remained until late in the 20th Century. The Battle at Brandy Station was the largest battle of the Civil War with 18,000 horseman and 40,000 ground troops. The painting depicts an extraordinary battle scene with rearing horses, charging cavalrymen supported by ground troops, flags, cannon and falling soldiers abound. Painting is signed and titled on reverse in bold black script “THE FIRST MAIN CAV’Y AT BRANDY STATION VA JUNE 9,’63, ISAAC F. EATON ARTIST BOWDINHAM, ME”. Framed in a large gesso gold frame. SIZE: Approx. 105″ wide x 62″ high. CONDITION: Frame generally good. Painting was cleaned and wax-backed at one time. 4-32769 JJ110 (35,000-45,000)

FABULOUS 1861 CIVIL WAR GRAND ILLUMINARY FLAG. This 6’ x 9’ Grand Illuminary of 33 stars has a canton design we have never seen before. Stars are of 3 different sizes. 6 stars in a circle in the center are 9-1/2”; 5 stars in secondary circle are 7”; and 22 4” stars occur in four 5-star clusters; and 2 individual stars adjacent to hoist in upper and lower quadrants. Cotton hoist is sewn over rope. Red stripes are wool blend; rest of the flag is cotton. Stars are hand-sewn and double appliquéd. All stripes and edging, which is found on all 3 sides, are also hand-sewn. This is a fabulous flag with great colors in excellent condition overall. This flag, along with the two PA flags in this sale, has been deaccessioned from the collection of the Soldier and Sailors National Museum and Memorial. Even though no accession notes can be found associated with the flag, the curator surmises that given the fine condition of the flag, it must have been in museum archives for many years and unfortunately lost its history. This is a fabulous flag. Condition and construction make this flag a centerpiece of any collection. CONDITION: : Minor moth damage to red stripes. Several stains. Rope hoist is broken near center. Several scattered small tears do not affect aesthetics. 8-76215 JS245 (8,000-12,000)

THE EARLIEST PENNSYLVANIA REGIMENTAL FLAG PRIVATELY HELD WITH FABULOUS, DOUBLE-CAPTURE, CIVIL WAR HISTORY. This recently deaccessioned flag from a Pennsylvania museum is pictured in Richard A. Sauer’s wonderful reference, “Advance the Colors: Pennsylvania Civil War Battle Flags”. This flag has been in the possession of the Soldier & Sailors Memorial for close to 100 years. Originally given to the museum by the widow of J. A. Heckert, who was a member of the 54th Pennsylvania Volunteers. This 25-star, silk, Pennsylvania militia flag is fitted in its orig 40” x 55” shadow box. When opened, the flag shows use and loss of stripes along fly edge. Hoist, however, is complete, being about 2” wide and about 47-48” tall. Orig 19th century provenance letter, which accompanies this flag, is written around an engraving of Ulysses S. Grant. Letter of provenance from Mr. Heckert of the 54th reads as follows: “Old Glory. This flag was captured and recaptured during the Civil War between the North and South from 1861 to 1865. The present owner prizes it highly as a relic for which thousands of lives were sacrificed to keep it unsullied. It was captured from a Pennsylvania Regiment by the Confederates during some engagement and taken to Petersburg, Virginia for safe keeping when it was recaptured by a Comrade of my company “C”, 54th PA, Volunteer Regiment after the evacuation of the city by the Confederates in April, 1865. The first Union troops to enter the city was a portion of the 24th Army Corps Commanded by General O. E. C. Ord., of which I was a member. The flag was presented to me by Nelson Meyers in 1869. The Number of the Regiment was defaced when recaptured. But its condition shows that it passed through many hard fought battles as it bears many Honorable marks. J. A. Heckert. 54th PA Vol. Inf. Regt. Author of the Story. Presented to Soldiers Memorial By the Widow Mrs. J. A. Heckert”. 25 stars on this flag date its manufacture between 1832 and 1836. A Pennsylvania Regiment used it during the Civil War, the identity of which is unknown, and it was captured by Confederates. In the spring of 1865, it was liberated from the city of Petersburg by Co. C, 54th Penn. Volunteers, of which J. A. Heckert was a member. This is a fabulous opportunity to own the earliest Pennsylvania military flag in private hands that has such a wonderful Civil War history, being captured by the Confederates and recaptured by the 54th Pennsylvania. CONDITION: Silk has numerous tears. Much of fly end of flag is missing. Canton is intact; however, as can be seen in photographs, several large chips of paint from central device are missing. Painted areas on canton are glued to a backing piece of paper in shadowbox. 8-76214 JS232 (40,000-60,000)

PATRIOTIC AMERICAN FLAG MADE BY SCHOOLGIRLS IN KENTUCKY IN 1861 WITH GREAT DOCUMENTED HISTORY. What a wonderful piece of history that was preserved and is being offered here. This 33” x 74” 9-stripe American flag with 18 stars. The 9 stripes and 18 stars exclude the founding Southern states and the 15 Southern slave-holding states and now represent the 18 “Union” Northern states. This flag has 9” x 6” paper label which reads “This flag was made by Miss. Charlotte Bright, the youngest teacher and several girls of senior class of Millersburg, KY, female college in 1861. It was hastily put together while a company of Confederate volunteers were being drilled on the street by Capt. Howard Henderson. The flag was waived from a college window while the men marched by, where upon the flag was saluted by the company with a volley of stones which broke the window and grazed the cheeks and heads of several of Kentucky’s loyal daughters who for several days ‘showed their wounds and called them honorable’ and grieved because those marks passed too soon away. Not a girl left the window under fire. Each one held to the flag – it had no staff – waving and cheering with a hardy ‘hurrah for the Union’ until the troops passed. The disturbance called the president of the school to the room. When he (Dr. G. S. Savage) appeared on the scene, as in duty bound, he reprimanded the girls and seized the flag. The president was very stern, outwardly, in word and gesture, for was not this a great breech of discipline which forbade any demonstration on any side and such . . . times of peace. But every girl knew she was applauded for the act in the heart of the loyal Dr. Savage. Mrs. J. D. Walsh, then Miss Bright, did not see the flag after that day until it was sent to her by Mrs. Savage in 1899.” In brown ink in center of flag reads a short inscription “From 1861 to 1899 was in poss. Geo. S. Savage”. This flag is entirely hand-sewn of material which we believe is polished cotton or polished linen. The 4-pointed stars are 5” across and have simple tack stitches to hold them in place. Materials used resemble those of lining material of dresses and coats of the day. Red stripes have faded greatly and now hold only a hint of pink. This flag, made of fine light cloth, has been well protected over the years and is still very sound and would display beautifully. CONDITION: Flag is intact with only a couple separations at seams of stripes. Some stitching to tacked stars is loose, but all stars are complete, attached and intact; for a couple, the fabric is folded over. There are scattered stains, some being brown and possibly the blood of the wounded students. 4-31601 JS247 (5,000-10,000)

16-STAR AMERICAN NATIONAL FLAG. This wonderful, hand-sewn, 38-1/2” x 53”, all cotton flag with a sewn rope hoist has a central star (6”) and 15 additional 3-1/2” stars sewn through in shape of a great star. This flag is very well made. The seamstress or seamstresses who made this showed great skill in their hand stitching, as can be seen in photos here. The colors are still vibrant. It would be difficult to obtain a better flag of this pattern. CONDITION: Very good overall with several tears and separations, scattered staining. 4-31498(15,000-25,000)

THE FIRST AMERICAN FLAG CAPTURED DURING THE CIVIL WAR. This iconic “ghost” of an American flag is the earliest documented and probably the first flag captured during the American Civil War. “This flag was hauled down by secessionists on January 12, 1861, fully three months before the firing on Fort Sumter, and so far as known was the first United States flag so desecrated in the Great Conflict”–so reads the provenance from the Soldier and Sailors Memorial, where this flag has been since 1912 just being deaccessed in 2007. Some of the first action of the Civil War occurred early in January 1861 around the forts at Pensacola, Florida. Florida had just seceded from the Union on January 10, 1861. The original museum tag reads ““PENSACOLA FLAG” This flag was hauled down by the Secessionists, (then citizens of Florida and Alabama) at Pensacola, Florida, on January 12th, 1861, (Three months before the firing on Fort Sumter), and so far as known was the first United States flag so desecrated in the great conflict, from 1861 to 1865. There is also authority for the statement that the gun first fired on the Union side, in that conflict, was fired in defending this flag-January 8th, 1861. During the celebration of the second election of President Lincoln, by the citizens of Pittsburgh, November, 1864, a banner inscribed, “THIS FLAG WAS TORN DOWN BY THE REBELS AT PENSACOLA AND RE-TAKEN BY THE LATE E.E. BRENNAND,” was attached to the flag and hung across Penn Avenue (near Tenth Street). The flag and banner have not been detached (or separated) since that time. Liet. E.E. Brennand in 1860 was assigned for duty on the U.S. Storeship “Supply”. This vessel, after a cruise of several months in Mexican waters, watching the activities of the :Southern Leasers?: arrived in Pensacola Bay January 12th, 1861, just in time to see the U.S. navy yard there fall into the hands of secession sympathizers, but too late to prevent it. While on shore Liet. Brennand captured this flag from a man whom he found trailing it in the dust. Liet. Brennand arrived in Pittsburgh February 3rd, 1861, brining the flag with him, which he presented to his sister, Mrs. John Erwin, and by her grandniece, Mrs. John Prichard, the flag was presented to Allegheny County Soldiers’ Memorial, through the Society of the Daughter of Betsy Ross on flag Day, June 12, 1912. Mrs. P.J. O’Connor, President, Daughters of Betsy Ross.” From Chapter 2, “Florida in the Civil War,” of Confederate Military History, Vol. 11, “WHEN on January 5th Senator Yulee wrote from Washington to Joseph Finegan at Tallahassee ‘the immediately important thing to be done is the occupation of the forts and arsenals in Florida,’ . . . As pointed out by Senator Yulee, ‘the naval station and forts at Pensacola were first in consequence.’ There was then on the mainland one company of Federal artillery, commanded by John H. Winder, at a later date a general in the Confederate service, but on account of his absence Lieut. A. J. Slemmer was in charge . . . Slemmer moved his force over to Fort Pickens on one of the vessels in the harbor under Commodore James Armstrong, commandant at the navy yard, and on January 12, 1861, the flag was lowered at the navy yard, which, with all the fortifications and munitions of war on the mainland, went into the possession of the State . . . two days later, Slemmer’s men watched as Southern soldiers moved into the other forts across the channel, removing the U. S. flags.” From Barrancas: The First Shots Fired in the Rebellion by Walter Giersbach, “The firing on Fort Sumter in Charleston’s harbor traditionally marks the opening salvos of the Rebellion. But before this assault on April 14, 1861, there was another battle—the first shots of the Civil War—hundreds of miles to the south in Florida. On Jan. 8, 1861, United States Army guards repelled a group of men intending to take Fort Barrancas in Pensacola Harbor. Historians say that this event could be considered the first shots fired on Union forces in the Civil War . . . Flag Officer Renshaw immediately ordered the National standard to be pulled down. The post, with ordnance stores valued at $156,000, passed into the hands of the authorities of Florida. The insurgents took possession of Forts Barrancas and McRay . . . The two vessels in the harbor, the Supply and Wyandotte, steamed out under the truce, but remained in the possession of the United States officers. Lt. E.E. Brennand was aboard the Supply.The 80 men under Slemmer at Fort Pickens remained defiant. The following night, a small party of armed men from the mainland reconnoitered on the island and a few shots were fired from the fort. On Jan. 15, Col. W. H. Chase, a U. S. Army officer of Massachusetts who had worked on building the forts and was thoroughly familiar with Pensacola Bay’s defenses, visited Fort Pickens in company with Capt. Farrand. Chase was in charge of all insurgents in that region and Farrand had been second in command at the Navy Yard. Chase obtained an interview with Slemmer and tried to persuade him to ‘avoid bloodshed’ by quietly surrendering the fort. Col. Chase said in conclusion, ‘Consider this well, and take care that you will so act as to have no fearful recollections of a tragedy that you might have avoided; but rather to make the present moment one of the most glorious, because Christian-like, of your life.’ Slemmer, it can be said, did make that a ‘glorious moment of his life’ by refusing to give up the fort.” John William Draper, in his 1867 publication, History of the American Civil War, states “In connection with the capture of the navy yard at Norfolk may be mentioned the disgraceful surrender at Pensacola in Florida by the officers having charge of it, and the honorable defense of Fort Pickens. Florida had seceded on Jan. 10, 1861, and immediately made a demand for the yard. At the time when the American flag was hauled down at the navy yard and the stores of guns and munitions turned over to the insurgents, Fort Barrancas was abandoned. But this scene of military disgrace was not consummated.” What a fabulous piece of American History, this flag and its attached pennant- the first American flag captures and then recaptured at the start of the American Civil War and then used to commemorate Abraham Lincoln’s re-election. Is there a more iconic American flag? Noted Civil War historian and Civil War flag expert & authority, Greg Biggs, has written the following report on this important & historical Pensacola flag: U.S. 33 Star Flag Taken at Pensacola, FL, January 12, 1861 By Greg Biggs In December, 1825, the United States Navy ordered the establishment a naval yard near Pensacola, Florida. This order sought to utilize the finest natural deep water harbor along the Gulf of Mexico. The complex was largely complete by the 1850’s and it encompassed the town of Warrington located a few miles west of Pensacola. To defend the naval complex and port three forts were built. The forts were Barrancas (built on the site of an old Spanish fort, Bateris de San Antonio de Barrancas, and incorporating some of its defenses into the new one), which was on the navy base itself and had a Advanced Redoubt covering its land side; Ft. McRee, which was built on a spit of land extending into the main channel west of the yard; and on Santa Rosa Island, Ft. Pickens. The latter fort was the largest and most heavily armed of the three, with 250 guns which covered the sea-side, the main channel and Warrington and Pensacola on the coast. However, it had not been occupied since 1850 and would need some work to be of use in early 1861. Only two of the forts survive today as Ft. McCree has sunk into the channel over time. South Carolina seceded from the Union on December 20th, 1860 and sent emissaries to her sister states to urge them to follow her path. By January, 1861, secession winds were blowing in Florida and, like some of her Deep South neighbors she did not wait for secession to act. On January 5th, one of the state’s U.S. Senators, David Yulee, advised Joseph Finegan, a member of the state secession convention (and future Confederate general) to seize the navy yard and forts at Pensacola. Both Yulee and fellow Florida Senator Stephen Mallory, future Confederate Secretary of the Navy, would do all they could to help prepare their state for action. The next day, a Florida militia company, the Quincy Guards, seized the U.S. Arsenal at Chattahoochee, FL. On the 7th, state forces seized Ft. Marion in St. Augustine and Ft. Clinch at Fernandina. In this same time frame, Georgia state forces seized arsenals and forts in that state as did the Alabama Volunteer Corps in their state. January 8th brought two important events. First, an Ordinance for Secession was introduced at the state convention in Tallahassee. Secondly, Col. William Chase, U.S. Army (retired) and by then a railroad magnate (and the engineer officer that supervised the building of the area’s forts), was ordered by Florida’s Governor Madison Perry, to take hold of the forts and naval yard at Pensacola. At the navy yard, U.S. Army Lt. Adam Slemmer, commanding Co. G, 1st United States Artillery, posted guards at Ft. Barrancas, fearing such a move. He also transferred the post’s ammunition to a more secure site, made the fort’s guns ready for action and raised the drawbridge. Near midnight a body of men approached the fort, which was usually not occupied, intending to take it. The fort’s guard challenged the body, and when he did not receive an answer, he fired. This can be considered the first shot of the American Civil War! On January 9th, Slemmer received orders from Washington to, “take measures…to prevent the seizure of the forts in Pensacola harbor by surprise or assault, consulting first with the commander of the navy yard.” The yard was commanded by Commodore James Armstrong. Both officers had been meeting for several days to plan how to hold the area with less than 50 Army troops and two Navy vessels in the harbor. The meetings also included their fellow officers USN Lt. Francis Renshaw; Cdr. Henry Walke, skipper of the USS Supply (a sail powered supply ship which arrived at the Navy Yard earlier in the day), and Lt. Otway Berryman, commanding officer of the USS Wyandotte, a screw-driven steamer. Both ships were considered Fourth Rate vessels and were armed with cannons, four and five guns respectively, although the Supply was not considered a warship. It quickly became apparent that there were not enough Federal forces to hold all three forts and the navy yard, so it was decided to transfer all troops and munitions that could be carried to Ft. Pickens. There, pending reinforcements, the force could hold out the longest. What could not be moved was to be destroyed. Armstrong agreed to place his two vessels under Slemmer to move the supplies, but he was dilatory in getting his vessels moving which cost valuable time. Slemmer threatened Armstrong by offering to report to Washington that he had done all he could to defend the area and that the Navy commander was not cooperating as he had agreed. Fortunately, the Wyandotte had just come out of dry dock (despite the efforts of pro-secessionist workers to keep her disabled) and was soon taking on supplies and towing the Supply to Ft. Pickens along with barges and flat boats. Slemmer’s troops, unable to carry all of the powder to Ft. Pickens, began to dump it into the bay while other stores were also destroyed. All of the guns in Ft. Barrancas that faced towards the bay were spiked. Working feverishly, by the end of January 10th, all stores from Barrancas and the Navy Yard that could be carried were in Ft. Pickens. Slemmer’s troops were augmented by 30 musket-armed sailors from the USS Wyandotte by order of her commander. Earlier in the day Florida became an independent nation, seceding from the United States. On January 11th, Slemmer, his meager land force now bolstered by the guns of the two vessels anchored by Ft. Pickens, began to feel more secure about his predicament. His feelings were soon dashed when Walke told him that Armstrong, now informed of Florida’s secession, had ordered the USS Supply to return to the Navy Yard. Concurrent with this news, Lt. Berryman told him that he was under orders to sail towards Cuba with the Wyandotte very soon. Slemmer was livid and fired off a note to Armstrong that Walke took with him. Armstrong replied that the USS Supply was technically not a warship and that prior Navy orders were for it to take on stores at Pensacola and sail for Vera Cruz to re-supply the U.S. Navy squadron there. By the time these exchanges had been completed it was too late for the USS Supply, which needed to be towed to the Navy Yard by the Wyandotte due to unfavorable winds, to actually move. However, the intrepid crew of the supply ship took one of its launches and sailed over to Ft. McCree, occupied only by a keeper and his wife, and broke down the gates of the fort. They destroyed most of the post’s powder, some 20,000 pounds, by dumping it into the sea and spiked all of the guns facing Ft. Pickens. Lt. Henry Erben, one of the McCree raiders, when arriving in the Navy Yard, asked Armstrong for permission to destroy that facility’s munitions and was refused. In the meantime, since January 9th, Florida’s two senators were telegraphing Gov. Perry that U.S. Army reinforcements were on the way to Pensacola and that the forts had to be seized by state troops before their arrival. They also informed Perry that William Chase had built the forts and knew them well and that troops from Georgia and Alabama would help. Chase had already been planning for such an event since late December, 1860 and, now a colonel of Florida State Troops as of the day after secession, was ready to go. Since early January, Chase had been in Alabama working with Governor Moore to elicit the help of his Alabama Volunteer Corps in taking the forts at Pensacola. It was well known in the Deep South that if the Federals continued to hold the forts it would be a strategic nightmare threatening Mobile and the lower parts of Georgia. Gov. Perry had approved Chase’s plan on the 6th and the next day Chase was in Mobile with the blessing of Alabama’s governor, to get troops to seize Ft. Pickens. Returning to Florida, Chase learned that Slemmer’s move to Pickens had thwarted his plan, so he decided to take all the troops he could to Pensacola. Help was on the way from Alabama. On January 9th, Col. Tennant Lomax along with 225 men of the 2nd Battalion, Alabama Volunteer Corps, took the train towards Pensacola. After marching for 40 miles, where the line was not yet complete, the tired men arrived in town late on the 11th. These companies included the Montgomery True Blues, Tuskegee Light Infantry, Wetumpka Guards, Metropolitan Guards and the Independent Rifles. For some, this was the only war-time action their units would ever see as many of the AVC companies disbanded not long afterwards. The people of Pensacola welcomed them as heroes. They were soon reinforced by two local Florida companies, the Pensacola Rifle Rangers and the Pensacola Guards, both of whom had formed not long after President Lincoln’s election. All troops were ordered to formation by 11 AM on January 12th. Commodore Armstrong, seemingly secure in the Navy Yard some miles away, was oblivious to the large force now arrayed against him. Certainly rumors and some verifiable intelligence had reached him, but being cautious, he did nothing to destroy or move the valuable military stores that still remained on the base. He later claimed that he was not ever ordered to do so. He was also concerned about the consequences should he actually destroy public property and nothing happened. His actions, or lack thereof, would earn him a court-martial. It took two hours for the Secessionist troops to march from Pensacola to the Navy Yard, which was only defended by 38 Marines under Captain Josiah Watson. Armstrong’s world soon crashed around him when a Marine guard informed him that several hundred troops with two state commissioners (and seemingly a lot of townspeople) were waiting at the main gate of Ft. Barrancas to see him. Indeed, all of the Alabama troops and the Pensacola Rifle Rangers, under Col. Chase, were arrayed in front of the fort when Cdr. Ebenezer Farrand, Armstrong’s executive officer, arrived to see for himself. After talking to the two commissioners, Richard Campbell, representing Florida, and Capt. Victor Randolph, representing Alabama, the party went to Armstrong’s office to continue negotiations. Realizing his hopeless situation, Armstrong agreed to surrender. He telegraphed Secretary of the Navy Isaac Toucey and informed him that there was a demand for the surrender of Ft. Barrancas and the Navy Yard and, faced with overwhelming odds, at 1:30 that afternoon he struck his colors. The lowering of the flag ceremony was respectful of Armstrong’s predicament. Post quartermaster William Conway refused Lt. Renshaw’s orders to lower the colors. He later received a medal from grateful citizens in California for his deed. Allegedly, it was Renshaw that lowered the flag, although a New York Herald letter dated January 29, 1861 written by him does not state, specifically, that he lowered the colors but that as senior lieutenant after receiving the order from Armstrong, “the time honored flags were hauled down.” Besides the Navy Yard’s garrison flag, a blue pennant, signifying Armstrong’s command, was also lowered. In their place was hoisted the company colors of Alabama’s Metropolitan Guards, which was the only flag available in Lomax’s battalion. The Supply and the Wynadotte were not included in the surrender. Over the next three days and operating under a flag of truce, all surrendered personnel were paroled and placed aboard the USS Supply along with their baggage and belongings. The Supply then set sail for New York on January 16th arriving on February 4th. The Wyandotte was ordered to follow on January 18th. The Supply returned to Pensacola with a load of supplies for the garrison at Ft. Pickens in April. After the surrender, the state troops moved quickly to occupy Fts. Barrancas, McCree and the Navy Yard. What they captured was tremendous – 338 guns of all types, mostly large caliber, over 12,000 projectiles and over 40,000 pounds of cannon powder! Also captured was a huge dry dock. On January 13th, Chase ordered that a new flag be hoisted upon the flag pole of Ft. Barrancas until further notice from the state secession convention. The flag was like that of the United States except that it bore a single white star in its blue canton. In the aftermath of the surrender of Ft. Barrancas and the Navy Yard, Commodore Armstrong was found guilty on two counts at his court-martial and suspended from duty for five years. Both Lt. Renshaw and Commander Farrand would resign their US Navy commissions and join the Confederate Navy as would some other officers and men of the Navy Yard. Tennant Lomax would become colonel of the 3rd Alabama Infantry and serve in the Confederate Army of the Potomac (later renamed the Army of Northern Virginia) and would be killed at the head of his regiment at the Battle of Seven Pines. Henry Walke, relieved of command of the Supply after arriving in New York, was court-martialed for bringing the paroled personnel to the city but received only a reprimand. He would go on to the Western Rivers Navy Squadron and take command of the timberclad gunboat USS Tyler in late 1861 before transferring to the new ironclad USS Carondolet in early 1862. He commanded this vessel from the Ft. Donelson Campaign and he was promoted to captain in August, 1862. After the promotion, he was given command of the ironclad USS Lafayette before moving onward with the command of other ships. Lt. Slemmer, in Ft. Pickens, would refuse three surrender demands over the next several days starting with one on the same day as the Barrancas surrender. Ft. Pickens would not receive heavy reinforcements until April 11, 1861. Ft. Sumter would be fired upon the next day in Charleston, SC. For whatever reason, several shiploads of troops remained at sea instead of landing at Pickens during the months after the surrender of Ft. Barrancas. Had they landed sooner, the Civil War would probably have broken out in earnest in Pensacola instead of South Carolina. Despite a couple Confederate attempts to take Ft. Pickens, including by storm on October 9th, the Battle of Santa Rosa Island, the post was destined to remain in Federal hands serving as a thumb in the eye of area commander Gen. Braxton Bragg. The Confederates would abandon the Pensacola area entirely in early May, 1862 USN Lt. Edward E. Brennand USN Lt. Edward E. Brennand, according to the Naval Official Records, went West after Pensacola serving with Henry Walke on the ironclad USS Carondolet. In February, 1862, in the Ft. Donelson Campaign, Brennand is listed as a Master’s Mate for the ironclad earning Walke’s plaudits for his conduct in the naval bombardment at Ft. Donelson on February 14th, in which the ironclads were defeated. By February 17th, Brennand was listed as First Master. On July 15, 1862, he was wounded in the engagement with the Confederate ironclad CSS Arkansas as she ran the fleet above Vicksburg, Mississippi. The vessel was struck some 13 times, most of the shots penetrating the casemate. Recovered and back in action by January, 1863, Brennand, in Walke’s absence, was listed as Acting Volunteer Lieutenant in temporary command of the Carondolet based at Island No. 10. That same month, Henry Walke was transferred to the command of the USS Lafayette and Brennand was chosen to command the “tinclad” gunboat USS Prairie Bird, a thinly armored converted stern-wheeler steamship bearing eight 24-punder guns. The vessel was stationed on the White River for much of the year. As part of the Mississippi River Squadron, Brennand and his crew carried out anti-guerrilla patrols and convoyed supply ships. On June 15th, men from his ship and the USS Marmora destroyed the town of Gaines Landing, Arkansas in retaliation for guerrilla attacks. In July, 1863, Brennand earned the commendations of Acting Rear-Admiral David Porter for his service. He continued in this duty until November 14, 1863 when, according to Edward Callahan’s List Of Officers Of The Navy of the United States (cited in the bibliography), he was accidentally killed. Callahan has the entry listed as Acting Volunteer Lt. Edward C. Brennand instead of Edward E. Brennand. This is, most likely, a typographical error as Callahan’s book does not show any entry for an Edward E. Brennand. Lt. Brennand’s Flag Forts like Pickens and Barrancas, as well as military posts, were served by two large flags. One was the garrison flag and the other was the storm flag, it being the smaller of the two. Since these flags were quite large, storm flags would be hoisted in times of storms, their smaller size creating less strain on the flag pole and on the flag itself. These were typically made of single-ply wool bunting, similar to flags issued to warships. The single-ply bunting allowed for more air to pass through the flag than did double-ply bunting. Confederate battle flags of the Army of Northern Virginia pattern as exemplified in both the Richmond and Charleston Depot models, were made of double-ply bunting. Based on the photograph of the Brennand flag, it too, was made from single-ply bunting. The Revised Regulations for the Army of the United States, 1861 states: “1436 – The garrison flag is the national flag. It is made of bunting, thirty-six feet fly, and twenty feet hoist, in thirteen horizontal stripes of equal breadth, alternately red and white, beginning with the red. In the upper quarter, next the staff, is the Union, composed of a number of white starts, equal to the number of the States, on a blue field, one third the length of the flag, extending to the lower edge of the fourth red stripe from the top. The storm flag is twenty feet by ten feet; the recruiting flag, nine feet nine inches by four feet four inches.” The description of the flag being offered for auction is an “8 foot regulation U.S. Navy 33 star ensign (stenciled on the hoist edge “Storm Ensign”). The flag, as issued, measured 8 by 4 feet. Obviously, the flag, although marked “storm ensign,” is not of the size stated in the Revised Regulations For the Army of the United States. This probably means that the flag in question belonged to the United States Navy which apparently had different regulations in place for storm flags. Howard Madaus, in his book Rebel Flags Afloat, mentions at least two Confederate Navy storm flags issued to warships. Since the Confederate Navy basically copied their regulations from the United States Navy, these can be useful for comparison purposes. The main battle flags for warships are called ensigns, and are flown from the stern of the vessel. Vessels were also issued “storm flags” (storm ensigns) for the same purposes as forts and posts on land as mentioned before. The storm ensign of the CSS Shenandoah (Museum of the Confederacy), measures 34 inches by 50 ½ inches. Another surviving storm ensign, for the CSS Chicora (Citadel Museum) is of similar size, 33 inches by 49 inches. This makes them roughly three by four feet in overall size. If storm ensigns for U.S. Navy warships of the time were of similar size, then the flag in question is not from a warship. Additionally, U.S. Navy regulations for ships do list flags of various sizes for the ensigns of warships based on their rating. The ensign for a ship of the Number One rating is listed as being 19 feet by 36 feet. The ensign for a Number Eleven rating is 4.2 feet by 8 feet. Flags for ships rated 10 through 14 (actually boats by this rating) are considered to be “boat flags.” Since the flag is marked “storm flag,” we can eliminate the possibility of this flag being a Number 11 rating ensign. Boat ensigns also typically had only 13 stars. The description further states the flag, “was hauled down by Secessionists at Pensacola, Florida at the Naval Fort on Jan. 12th, 1861.” First, there was no “Naval fort.” This statement has to mean Ft. Barrancas, which was within the naval base complex. If Ft. Barrancas was equipped with a regulation “storm flag,” then this banner is too small to have served that purpose. Thus, this is most likely not the storm flag for Ft. Barrancas. The flag that Armstrong pulled down, and seemingly did not surrender to the Florida/Alabama state forces (and probably took with him), was the fort’s regulation garrison flag. No accounts from the Southern side state anything about keeping the flag once it was hauled down. Additionally, nothing from the reports of the day indicate bad weather where the garrison flag would have been replaced with the storm flag. Continuing the Navy connection, and since there is no documentation of any other U.S. flags being removed from other flag poles of the Navy Yard, we must turn to the possibility of it being the storm flag for the Navy Yard itself and that it had been removed from the flag storage locker for the yard. The flag is listed as a “U.S. Navy storm ensign,” which helps make a more positive tie to it being a naval flag. Research into the regulations for flags used at Navy Yards has not yielded anything conclusive as of the date of this writing but it can be presumed that they, too, had their equivalent of garrison, post and storm flags to be used on the flag pole of a base. Navy yards supplied most of what naval vessels needed to remain at sea doing their duty, and they maintained a large stock of flags for those purposes. A review of the flags taken from the U.S. Navy Yard at Gosport, VA (near Norfolk) is illustrative of the numbers and types of flags that could be found at such a facility. Rebel Flags Afloat mentions that 343 flags, mostly distinguishing flags of foreign nations, were taken at the yard by Virginia state forces. Additionally, a large supply of bulk wool bunting was taken at the yard, some 130 pieces (each “piece” measuring 40 yards in length with widths running from 12 inches to 18 inches), was also captured. The flag in question bears 33 stars. The 33 star U.S. flags came to pass on July 4, 1859, after the admission of Oregon on February 14th of that year. The Flag Act of 1818, still in effect today, states that on the 4th of July after the admission of a new state, their star would be added to the flag of the United States. So this flag is the proper model to have been in use at the Navy Yard in January, 1861. They would be replaced by 34 star flags on July 4, 1861 after the admission of Kansas on January 29, 1861. The description of this flag alludes to it being, “trailed in the dust of a city street,” as well as, “this flag was drug through the streets of Pensacola in celebration.” The story states that USN Lt. E. E. Brennand, who brought the flag back to his home in Pittsburgh, PA, saved the flag from this fate and took it with him when the USS Supply, on which he served, left the port. It further states that Brennand arrived at his home in Pittsburgh, PA on February 3rd, 1862. There is a problem with this, however. Brennand was still at sea on the USS Supply at this time, which did not arrive in New York, according to the ship’s log abstracts in the Navy Official Records, until February 4th. It would have taken a full day or two of travel to reach Pittsburgh. The flag was donated sometime later to the Sailors & Soldiers Museum of Allegheny, PA. by Brennand’s son and it is probable that the provenance was written at this time. It is quite likely that Brennand’s son had the date of his father’s arrival at home incorrect. The USS Supply spent three days loading people and their belongings on board for the trip to New York. Brennand most certainly was on and off the ship during this time helping to load its cargo. He undoubtedly had contact with the secessionists occupying the Navy Yard and Ft. Barrancas during this time. However, no evidence of a mob taking any U.S. flags has been found in any period newspaper articles, the Official Records of the Union and Confederate Navies in the War of the Rebellion, or Pensacola In The Civil War, written by George F. Pearce. The whole affair of the surrender of the fort was handled with grace and dignity by both sides. Brennand may well have come across someone going through the Navy Yard flag locker pulling out flags and, upon seeing this storm ensign, decided to drag it on the ground. Brennand took offense to this and seized it from him. Additionally, the Navy Yard was in Warrington and not Pensacola. There is also no written record of the USS Supply being at Pensacola, but direct evidence from Commander Walke’s log abstracts that it was anchored just off the Warrington Navy Yard after ferrying supplies to Ft. Pickens along with the USS Wyandotte, and taking on passengers, based on Armstrong’s orders. The Pensacola attachment is probably just an error on the part of whoever wrote the provenance. Regarding its condition, the flag does, however, exhibit severe damage above what wear and tear from normal use would cause, so there is no reason to doubt that portion of the provenance. The flag is in shreds so the abuse was quite extensive. Further history of the flag states that it was flown again to celebrate the re-election of President Abraham Lincoln in November, 1864 by the cheering people of Pittsburgh. During this time, a banner was attached to the flag telling of its taking at Pensacola by the “late E. E. Brennand” and that he had retaken the flag from the rebels. This banner and the flag have been together ever since. Considering Brennand’s deed and when he did it, one can most certainly make the claim that it was the first Union flag taken – and retaken – during the Civil War. Conclusion The flag is authentic to the early Civil War period due to the number of stars on the flag, its single-ply bunting construction and, most importantly, the provenance for the flag. It descended from the family of USN Lt. Edward E. Brennand who had an illustrious naval career before his untimely death in November, 1863. His son donated it to the museum from whence it comes today confirming a direct connection to this officer. The flag does exhibit rough treatment and was probably abused by someone at the Navy Yard despite the lack of evidence of any mob celebrations of the surrender. It is my opinion that the flag was probably removed from the yard’s flag locker by an individual and treated quite roughly while in his possession. Brennand seized the flag back from this person (or couple persons), something that would have been very difficult to achieve from a mob considering that he was working under a flag of truce at the time and due to sheer difference in numbers. This flag was, most likely, the storm flag of the Warrington Navy Yard based on its size and the fact that Brennand’s ship was busy evacuating the staff of that yard where he certainly came into contact with Floridians while doing so. It is living proof of the love of his nation’s flag that Edward E. Brennand saved it from long term capture. Greg Biggs Military Historian Clarksville, TN August 16, 2007 Sources: Official Records of the Union and Confederate Navies in the Civil War, Series I, Vol. 4, Vol. 19, Vol. 22, Vol. 24 and Vol. 25 (Washington, Government Printing Office, 1896) List Of Officers of the Navy of the United States and of the Marine Corps from 1775 to 1900 Compiled From the Official Records of the Navy Department (Edward W. Callahan, Registrar, Bureau of Navigation, Navy Department, L.R. Hamersly & Co. , New York, 1901) U.S. Civil War Navies website – www.tfoenander.com Pensacola In The Civil War, Pensacola Historical Society Quarterly, Vol. IX, No. 2, Spring 1978 Pensacola In The Civil War: A Thorn In The Side of the Confederacy, by George F. Pearce (University Press of Florida, Gainesville, 2000) The Civil War In Florida, Vol. 4 – Florida’s West Coast and Panhandle, Lewis G. Schmidt (Privately published, Allentown, 1992) Warships Of The Civil War Navies, Paul H. Silverstone (Naval Institute Press, Annapolis, 1989) The Flags Of The Union: An Illustrated History, by Devereaux D. Cannon Jr. (Pelican Press, Gretna, 1994) Rebel Flags Afloat: A Survey of the Surviving Flags of the Confederate States Navy, Revenue Service and Merchant Marine, by Howard Michael Madaus (Flag Bulletin No. 115, January-April, 1986, Vol.XXV, Nos. 1-2) The American Flag: Two Centuries Of Concord and Conflict, by Howard Michael Madaus and Whitney Smith (VZ Publications, Santa Cruz, 2006) Columbus (GA) Times, February 9, 1861 Baltimore American, January 24, 1861 CONDITION: As can be seen in the photographs of this flag, much of the stripes are worn and missing; however, the canton is fairly complete with all 33 stars. The hoist is sound. Markings on hoist are very good. Attached pennant is intact with one approx. 2” x 2” hole and several large stains. Pins that attach hoist to celebration pennant have been removed but remain with flag and pennant. 8-76213 JS244 (40,000-60,000)

RARE C.W. 10TH ARMY HEADQUARTER BRIGADE FLAG FOR THE 4TH U.S. COLORED TROOP! IDENTIFIED TO MAJ-GEN. SAMUEL A. DUNCAN. This headquarters corp. flag is correct, orig and extremely rare. It was sold out of Gen. Duncan’s family estate several years ago with the General’s coat and the 4th USCT Federal National Color. Brevet Maj-Gen Samuel A. Duncan was a graduate of Dartmouth College and lived in Meriden, NH. He was directly commissioned by Pres. Lincoln as Col. of the 4th USCT(color Troops) Infantry Reg. in September, 1863. He was wounded leading an attack upon Newmarket Heights in Sept. 1864, being brevetted Brig. Gen for this action. He was later brevetted to Maj-Gen. HE served as officer in command of the 2nd Brigade, 3rd Div, 10th Army Corp from March 1865 to June 1865. During this time period, Duncan and his colored infantry brigade participated in the surrender of Gen. Johnson’s Army of the Carolinas in the spring of 1865. This flag dates to the service from the March 1865 to June 1865 under the command of Col/Gen S.A. Duncan, 4th US Colored Troops, when he was in command of the 2nd Brig including the 4th, 5th, and 39th US Colored Troops as part of the 10th Army Corp, Gen.Terry’s Dept. of NC. The flag is a triangular shape pennant marked to signify the 2nd Brigade, 3rd Div, 10th Army Corp. It is overall sized at approx. 54″ on the hoist by 43″ on the fly to the point. The flag is based on a white linen leading hoist edges (about 4.5″ wide)with seven hand sewn “eyelet” holes. The main body of the flag is a red wool base being made from two horizontal pieces joined in the center with the hand stitched applied blue bastioned fort outline with white square (10th Army Corp symbol) in the center. The blue bastion center is about 19″ across (tip to tip) with the center white being a 3″ square. This flag has been personally examined by the national recognized expert (Mr. Howie Madaus)on Civil War flags and has a pending letter of authenticity attesting to its originality and use. Unfortunately, Mr. Madaus passed away while the letter was pending, but correspondence between Mr. Madaus and the owner is available to the buyer. It has been explained that this flag very closely matched the brigade flag (3rd Div, 1st Brig. 10th AC) of Col. Bates (30″ USCT) that is in the possession of the Milwaukee Public Museum, ex- Chicago Historical Society. Bates’ brig. flag is also of 2-pc red wool and there is a strong feeling by the museum staff that it was made from a captured Confederate hospital flag(red). See the book, “American Military Equipage 1851-1872 Volume II” by Todd, pg 323-351 for text and examples on Corp Flags. This may be the only Civil War 10th Army Corps flag in private hands. This flag will display beautifully. CONDITION: Fabric of this flag is sound overall with good color. Hoist and central device are completely intact and in good condition. Red field shows wear and about 25% is missing along the edges and the fly. 4-32926(10,000-15,000)

1ST NATIONAL CONFEDERATE FLAG OF GENERAL GUSTAVUS SMITH 118” x 52”. Rarely are offered Confederate flags with such good provenance and history as this one. Five United Confederate veteran letters are associated with this flag which read as follows: “Kentucky Division, United Confederate Veterans John C. Breckinridge Camp, 100, United Conf. Veterans “Leafland” near Lexington Ky. Thirteenth of Oct. 1896 My Dear Col Morriss- It was my misfortune to be absent from from(sic) “Leafland” for a few days when your letter of Oct 9th reached there. It has only this minute been read by me & I beg of you to pardon my delay. To be in Richmond again as the daughter of a true Confederate soldier would be indeed a great pleasure but sir -nothing- & I can say it truly- could add more to my happiness than to be present on Thursday next & tenderly pass over to the Ladies of the Memorial Museum of Richmond the flag of Gen. Smith around which so many sad & loving memories. Yes- to place it with the loving hands in the very room where hangs the flag of the old Orphan Brigade- & other trophies of Ky’s proud sons. You are right- As time rolled on- Ky gave her best- her truest- her noblest & so our treasures one by one all by the fattlefield were won & high around these stood Gustavus W. Smith. I can not be with you in person, but my heart goes forth in gratitude & tears come unbidden to my eyesas I thank you for the honor confered on Ky. “They bid us tell the story of our nation’s golden past and sing her hymns of Conquests and chant her dirge at least but when thr wounds are fresh and quivering.Is there any place for art? Can we present the stories graven on the tablets of the heart? In no truer, no more tender hands could you have placed this sacred trust than in the hands of the Grand Confederate Women of Richmond. Ou cause, our veterans, our relicts shall ever live in my heart- Our poet priest of the SOuth thus speaks to us in the conquered banner- “Touch it not -unfold it never- Let it drop- there unfurled forever- for its peoples hopes are dead.” We of the dear Southland would say unfurl those banners- not in war but in peace. Carry them on high- show to the world they are dear to us yet – build a Memorial faster- more magnificent than any on our Globe. Say to our people although all was once dark & drear- bright and joyous days have come- & we love “their curse” with a better love, & a fonder devotion then ever- Allow me again to thank you for your great kindness & on next Thursday may the bright & beautiful sun shine forth in all its glory- just kiss with its warmth & brightness. The stains of time upon the silken folds of the flag that Ky once bore so proudly. Most Cordially Yours Julia Hughes Spurr Sponsor Ky. Division UCV 1896 Pine Grove, Ky” This flag is made of cotton with 11 sewn through stars. Based on the dimensional ratio, construction and materials, this flag was most likely early war. Howard Madaus, in his notes, states he felt this flag was probably Gen. Smith’s headquarter flag in VA in 1861. Gen. Smith probably would have had this flag in his possession on his last appointment near Savanna, GA 1864 and 1865. Gen. GUSTAVUS SMITH was born in KY and graduated from West Point prior to the Mexican War where he saw service and was also an instructor at West Point. Smith was commissioned Maj. Gen. in the Confederate Army in Sept, 1861. He commanded a brigade of the Army of Northern Virginia during the Peninsula Campaign. He commanded the entire army for a portion of the battle of Seven Pines after Gen. Joseph E. Johnston was wounded. We feel this flag would have accompanied Gen. Smith during this campaign. Gen. Smith served as Secretary of War for the Confederacy during Nov. of 1862. He resigned early in 1863, but was appointed Maj. Gen. of the Georgia Militia, to organize Georgia State forces and lead troops during the Atlanta Campaign. This is a fabulous flag with vibrant colors, great history and provenance that will display beautifully. Confederate cotton flags are scarce and generally are much better preserved than their silk or wool counterparts; cotton flags such as this are much easier to conserve and frame. CONDITION: Very good overall, with good strong colors and only scattered tears, loose stitches and holes. As mentioned in description, flag is missing its hoist. Documents associated are good overall. 4-32587 JS11 (35,000-50,000)

CONFEDERATE 1ST NATIONAL FLAG PURPORTED TO BE CAPTURED FROM BLOCKADE RUNNER IN SAVANNAH, GA. This 6 x 9 foot machine sewn flag was purchased from Dale C. Anderson Company in 1978. There is a letter of authenticity from Mr. Anderson dated Jan. 29, 1980 which reads: “This letter is to certify the authenticity of the flag which you purchased from our catalog number 30, fifth issue of 1978. The specimen, a regulation sized example of the stars and bars, or first national flag of the Confederacy measuring approximately 6 x 9 feet. (item E1 in the catalog) was originally purchased from a family in Savanna Georgia who related its word of mouth history to the buyer. They said, and we have every reason to believe that the flag was flown on a blockade Runner which docked at Savanna, and that the family had acquired the flag during the last stages of the war and had preserved it to the date of sale. Our company purchased the flag from the original purchaser about a month after the flag left the family. We have since attempted to obtain further written history such as the family name and ship name, but the people wish to remain anonymous. Thus, we can only relate what we at first learned. The flag itself meets all criteria for judging origin and age”. Stars are cotton and canton and stripes appear to be wool bunting. “CONFEDERATE FLAG. A fine quality, unquestionably orig, regulation size example of “THE STARS AND BARS”, the flag recommended by the Committee on a Proper Flag for the Confederate States of America”, appointed by the Provisional Congress (CS), in its report of March 4, 1861. Nothing better or more eloquently represents the Confederacy, its idealism, standards, objectives and resolve, than the banner around which its citizens and soldiers rallied. No one single thing can bring to mind so many visions, or evoke more severe and varied emotional reactions, even today, than THE STARS AND BARS, which knew a free wind for four incredibly significant years of this Nation’s life. If one cares to represent Southern history , whether personally in agreement with the Confederacy or not, through the collection and display of some of its artifacts then nothing could serve better, or more brilliantly, than an orig flag. This specimen, which we offer would be difficult to better measuring 6 feet along the hoist and 9 feet along the fly, and retaining its brilliant red, white and blue colors, the red and blue in standard flag bunting. The 13 white stars are linen, double sided, just lightly yellowing, and are a bit over 5 inches high. The hoist is re-enforced with blue and white striped canvas, into which is sewn a rope, looped at top, hanging free at the bottom, about 24″. Construction is basically, very early machine stitch, as are a good proportion of the Confederate flags in the Confederate Museum at Richmond. Blue field is extremely excellent, with few 1/4″ holes and few 1″ ones. Both top and bottom red stripes are as fine or better with only and occasional and expected 1/4″ hole. The white stripe has two larger frayed spots just big enough to pass a hand through and some smaller frays, all of which is quite expected and far better than most ever encountered, This flag is known to have flown on a blockade runner at Savannah, Georgia, where it has been carefully preserved ever since. Something rarely available, and amazing for its fine condition”. CONDITION: Overall this flag is very good with good color, scattered moth damage and soiling. 4-32627(10,000-15,000)

Revised: 10/19/2007

(Additional Information)Flag was not decommissioned from Harrisburg State Museum, but rather from the Pennsylvania Capital Preservation Committee.

35 STAR CIVIL WAR MILITARY ISSUE BATTLE FLAG IN THE PHILADELPHIA DEPOT PATTERN (DOUBLE OVAL MEDALLION), DECOMMISSIONED FROM THE HARRISBURG STATE MUSEUM, DESCENDED FROM LT. COLONEL JOSEPH HILL SINEX, COMMANDER OF THE 91ST PENNSYLVANIA VOLUNTEERS. 35 star Civil War, Union Army Battle flag, found among the possessions of Lt. Col. Joseph Hill Sinex of the 91st PA. Inf.y, handed down through his family, then lent to the Harrisburg State Museum with two other flags that belonged to Sinex (including a 34 star, NY Depot pattern battle flag and a small federal standard – not included in this lot). The three flags were decommissioned in 2006 at the bequest of the owner, who required nursing care and wished to sell them. This is the most graphic of the two Sinex battle flags, with its dynamic, Philadelphia Depot star pattern that consists of a dbl oval, standing on end, with a center star and a flanking star in each corner of the vertically-oriented canton of fine blue silk. It also survives in far better condition than the 34 star example, which was shredded to a fragmental state, missing most of the content of its stripes. The stars are gilt-painted, like those of most Union Inf. battle flags, and there is a silk fringe on three sides. Such flags almost never come available for public sale, as most are in museum collections, so the opportunity to add one to a private collection is very rare. The 91st PA Vols was recruited by Edgar M. Gregory and Edward E. Wallace during the fall of 1861, and mustered into service at Camp Chase, at Gray’s Ferry, on the Schuylkill River near Philadelphia. The first act of the 91st was the protection of Washington, DC and guard duty at the old capital prison. It then moved around VA and MD on various patrols until McClellan was replaced by Burnside and the Union Army was reorganized. Joining Hooker’s division, the 91st soon after engaged the enemy at the Battle of Fredericksburg, where it lost two officers and eighty-seven men. Capt. Sinex took command of the 91st in Jan. of 1863, following the resignation of Lt. Col. Wallace. In May the 91st took part in the Battle of Chancellorsville, where Sinex was dismounted and significant losses occurred again among Union forces. All but two of the regiments involved were mustered out afterward. One of the two that remained was the 91st PA, which transferred to the Third Brigade (Sykes still commanding). Then, in June, Gen. Meade took command of the Army and Sykes replaced him as Corps Commander. Soon after the 91st found itself at Gettysburg in the Battle of Little Round Top. This flag was probably made after Gettysburg, because it has 35 stars instead of 34. But the fact that it belonged to Sinex, in command of the 91st at Gettysburg, the most important battle to most collectors of Union Civil War artifacts, the connection is of great significance. Before the war ended, the 91st participated in many other battles where it was heavily engaged, including Richmond, Cold Harbor, and Hatcher’s Run. Accompanying the flag is a picture taken by the famous photographer Mumpher, apparently before Joseph Sinex died on 6 October 1892. SIZE: Approx 6’ x 6.5’, which is the most common size for almost all Union inf. national colors. CONDITION: Flag is framed in pressure mounted Plexiglas, largely intact, with some losses and splits, particularly at the fly end. As can be seen in the illus there are various separations and some losses. In the period between 1820 and 1850, silk merchants began to sell silk by weight instead of length. To make it heavier, weighting agents were added to the fabric. These increased the price of silk but were harmful to the fabric over time. This is why most all silk flags made between 1820 and the 1st quarter of the 20th C. (which encompasses most flags carried by ground forces) often exhibit a significant degree of breakdown. The state of this particular flag is far better than most surviving examples. 4-32854 JB1 (15,000-35,000)

EXCEPTIONAL CONFEDERATE STARS & BARS OF JOHN B. G. “KENNEDY’S BATTALION OF ORLEANS” PARRISH, LOUISIANA, WITH GILT-PAINTED LETTERING IN THE CANTON. Extraordinary, Stars & Bars format, flank-scale, confederate regimental battle flag with one of the most desired traits in flag collecting. This is the rare presence of gilded lettering in the canton that reads: Kennedy’s Battalion Of Orleans! First National pattern Confederate flags that share this highly sought-after feature, are practically non-existent outside museums and state collections. The sale of this flag at public auction presents a very, very rare opportunity. The overall construction of the flag is of commensurate quality. The metallic bullion fringe and 11 stars (separately sewn to each side) were probably obtained in Paris. The French had long been the master-producers of this type of decorative trim. The sequins and fancifully twisted wire were typically made of precious metal, traditionally with a content of approximately 98% silver and 2% gold (to add a yellow tone and deter tarnishing). The stars are created by the layering of spiral wire and sequins, and their three-dimensional form adds even more visual impact to the bold, circular text. The canton and stripes are made of fine silk. The lettering is hand painted in the metallic gold often seen on the highest quality American battle flags of the 19th century. The canton is pieced in two vertical sections, which represents careful conservation of available fabrics. This is typical of most 19th C. flags, both those made during and outside times of war, but it can be more readily expected in a wartime example. In August of 1861, the 5th LA Inf Battalion, a.k.a. “Kennedy’s Battalion of Orleans”, was sworn into Confederate Service at Columbus, KY. Commanded by Lt. Col. John B. G. Kennedy, the group had formerly been part of the LA Militia, which was formed in 1860, and its men were from the Orleans Parrish. The battalion was sent to Columbus by Gov. Moore, to protect the “Columbus Line” along the Mississippi River. This included the town, itself, plus the Madrid Bend of the Mississippi and Island #10. Gov. Moore was responding to Sec. of War Leroy P. Walker’s March 9th, 1861 appeal to LA for 1,700 troops, which were requested to protect the Mississippi defenses. The LA Legislature approved the request on March 15th, 1861 and authorized the equipping of state troops. On Nov. 7th of that year, the Kennedy Battalion fought against Gen. Grant at The Battle of Belmont. Neither side fought well, but Grant believed his attack against Columbus prevented the Confederates from invading Missouri. On Feb. 9th, 1862, the Kennedy Battalion of Orleans was reorganized into the 21st LA Inf, again commanded by John B. G. Kennedy. The newly formed regiment was again ordered to strengthen Island #10, which controlled primary access to the Mississippi. On Feb. 23rd, 1862, a portion of the regiment began to construct batteries for heavy artillery pieces. Then, on March 17th, 1862, the regiment left for Fort Pillow, serving the garrison there until the fort was evacuated in May. The regiment went on to Corinth, where they fought a skirmish at Bridge Creek. It then joined a larger portion of the Confederate Army, traveling to Tupelo, where, on July 28th, Gen. Bragg ordered the regiment disbanded by Special Order #222. So Kennedy’s Battalion (5th LA), then Regt (21st LA), served from August 1861 to July 28th, 1862. Very little is known about John B.G. Kennedy. He enlisted at the rank of Lt. Col. and was later promoted to Col, though the date of his enlistment and former residence are unknown. After the regiment disbanded, Kennedy spent the remainder of the war trying to get reinstated. In fact, it appears that went so far as to falsify orders, having been branded a “Thief and Impostor” by the Inspector Gen.’s Office on November 13th, 1862. He afterwards traveled to Augusta, GA and attempted, without success, to become a purchasing agent. Since Kennedy’s Battalion became Kennedy’s Regiment in 1862, one can be sure that the flag was made around the time that Kennedy’s Battalion was mustered into active service. It may have been brought out again, to be carried by Kennedy’s Regt, though it would not have been made specifically for that unit, with the name “Battalion” on the flag. The flag’s known specific history of use, when combined with such extraordinary graphics and a small, though impressive, easily displayable size, result in one of the most interesting Stars & Bars that we have ever offered for sale. PROVENANCE: Special thanks to Bill Floyd for information on the Kennedy Battalion. Sources: Guide to Louisiana Confederate Military Units by Arthur Bergeron Military Record of Louisiana by Napier Bartlett Microfilm Publication 320, Roll#316 Compendium of the Confederate Armies: Louisiana by Stewart Sifakis CONDITION: Flag has been pressure mounted in an archival manner between 100% cotton velvet and u.v. protective acrylic. Frame is a black painted and gilded example of the highest quality. Approx 50% of the white silk in the central bar is absent, along with about 5% of the same fabric in the sleeve area. These were masked by placing silk fabric of similar coloration behind the orig white, during the conservation process. Silk of this period almost always experiences breakdown due to addition of weighting agents that were caustic to the fabric over time. These weighting agents increased the amount of money that a merchant could obtain for the silk, sold be the pound instead of by length. The other two red bars have faded to a very attractive salmon color. They were never truly red, but were a strong pink, like a blood red sky. Royal blue, as usual, retains strong color. Fringe and stars are in very good condition. Lettering has experienced some paint loss. 4-32853 JB2 (35,000-55,000)

34 STAR, SWALLOWTAIL, CIVIL WAR GUIDON OF COMPANY I, 15TH REGIMENT PENNSYLVANIA CAVALRY, PRESENTED TO THE COMPANY’S BUGLER, CAPTAIN ABRAHAM CLARENCE MILLER. ACCOMPANYING ARE MILLER’S BUGLE, A PHOTO OF MILLER HOLDING HIS BUGLE, HIS DISCHARGE PAPERS, AND 23 FIELD-WRITTEN LETTERS. 34 star, swallowtail, Civil War guidon of Co. I, 15th Regt PA Cav, presented to the company’s bugler, Capt. Abraham Clarence Miller. The flag comes with a tremendous amount of related material and provenance and was kept in Miller’s family until 2003. Accompanying the flag are the following articles: ? Miller’s Civil War-carried brass bugle and sash (archivally framed in period gilt molding) ? An albumen photo of Miller holding this exact bugle with the sash over his shoulder (also archivally framed in period gilt) ? Miller’s discharge papers (also archivally framed in period gilt) ? 23 letters that were written by Miller in the field. ? A pair of ¼ plate tintype photos picturing Miller and a woman who may be his wife, (Margaret), or possibly his sister, together in their original press-decorated gutta-percha cases. ? A fairly extensive number of other related papers and items, including a copy of Miller’s file from the Nat. Archives showing muster rolls, etc., his certificate to teach school (gained in 1866 immediately following the war), a small homespun linen bag with a script initial “M”, found in a mid-19th C. lap desk in the family home, and other interesting paper documents. ? Two early 20th C photographs of the flag and a late 20th C. photograph of the bugle, discharge papers, and albumen photo, as they hung in their previous frame in the family home. This is a real Civil War carried flag that was truly used and reflects that usage. This is the proper state for a flag not put away for safekeeping, but issued to a Civil War unit and carried on horseback throughout the muck, mud and blood-strewn fields, woods, and rivers of the worst war ever witnessed on American soil. This is particularly true for land-use, Union army, Civil War battle flags and guidons, which were made of fine silk with painted stars and other elements. Some flags saw less use than others, of course, but those that were carried for a prolonged period should show appropriate wear. So use is one reason for losses, but other reasons include the acidity of paint and the caustic nature of the mineral salts and other weighting agents used in the fabric. In the period between 1820 and 1850, silk merchants began to sell silk by weight instead of length. To make it heavier, weighting agents were added to the fabric. These increased the price that could be obtained but were harmful to the fabric over time. This is why most all silk flags made between 1820 and the 1st quarter of the 20th century (which encompasses most flags carried by ground forces) exhibit some degree of breakdown. If you have ever visited an armory and seen the state of Civil War period, Union flags rolled on their staffs within glass display cases, know that a combination of hard outdoor use, manner of construction, and manner of storage accounts for their present condition, which, more often than not, is far beyond the largely intact state of this particular swallowtail guidon. The flags eventual owner, Abraham Clarence Miller of Harrisburg, mustered in at the Carlisle, Pennsylvania Barracks on September 10th, 1862 for a three year term of service. He was 18 years old at the time. An experienced veteran soldier by the war’s end, he was discharged as the company bugler in Nashville, TN on June 21st, 1865. Miller then returned to PA, where he became a school teacher (as evidenced by his teacher’s certificate, included in this grouping). He died in Harrisburg in 1906 at the approx age of 62. Sometime after his death the family (or a portion thereof) moved to Hagerstown, MD, taking the flag with them, where it remained until 2003. The aged woman who owned the flag relayed that she was effectively the last of his direct descendents and, having no further use for it in her old age, decided to sell it. Included as part of item (7) on the above list are photos taken inside and outside of her home of the flag and some of the other objects. Twenty three of Miller’s hand-written letters accompany the lot. These detail, among other things, various battles of the war, grumblings about various officers, etc. It is reported that somewhere in the letters Miller speaks of his encounter with David Boone, son of Daniel Boone, who bragged about his father. But we have not had the time to read them thoroughly and so can not attest to the fact. All the documentation one could reasonably wish for and more to accompany Civil War relics is present. The 15th PA. Cav. fought primarily in the Western Theater, particularly in TN and AL. According to “Advance the Colors: A Survey of Pennsylvania Civil War battle flags”, by Richard A. Sauers, Capital Preservation Committee, 1991, this is the only known surviving guidon of the 15th PA. Cav. The guidon of Co L did exist into the 20th C. It was received by the PA State Adj. Gen.l on July 20th, 1920, then sent to the PA. State Arsenal, but it has since disappeared. A relatively large number of Civil War era bugles exist, but an identified bugle with its original sash, pictured with the soldier who carried and blew it during the war, is a very rare find. Though we are sure others exist with such documentation, we have never encountered one and they are remarkably rare. The albumen photo is large in size, which makes it a great visual compliment to the grouping. It was taken by Roshon’s Studio in Harrisburg, and shows Miller in full uniform, complete with kepi, holding the bugle with the sash draped over his shoulder. Roshon Commonwealth Gallery was located at 19 N 3rd St. and a photographer by the name of John W. Roshon was its proprietor. His photographs appear in the State Archives from 1866-1955. The studio evidently provided this beautiful decorative matting with six-pointed Stars of David along the perimeter. Since the photo and the discharge papers were similar in size, they were re-mounted in matching, 19th C, gilded moldings. Gilt frames of similar color, period, and quality were also chosen for the flag and bugle, which makes for a dynamic display. Civil War period, military-issue grade Stars & Stripes flags seldom come available for sale in today’s market. Surplus flags existed after the war and were often gifted to veterans and G.A.R. chapters. These lack a letter in the center of the medallion star field and account for most of the swallowtail cav. guidons that have come up for sale in recent years. With a letter in the flag’s center medallion, however, one can be more certain that the flag was actually carried, as opposed to having become post-war surplus. The most obvious proof of the flag’s use during the war is the state in which it now exists. Losses are greater at the top and bottom of the fly end, where wind damage was greatest, and there is clear indication of its natural wear in the field. Such examples are almost universally in museums and are exceptionally rare on the open market. Most are not available because the state laid claim to government issued flags. In this case, however, according to expert, Howard Madaus, former curator of the Civil War museum in Harrisburg, PA, and the foremost expert in the field of Civil War battle flags, this is a very early war flag and would be exempt from such claims because it was purchased by the volunteer unit with locally donated funds, not with state or federal monies. Madaus viewed this flag shortly after its acquisition from the family. 34 Star Flag History: Kansas was admitted into the Union as the 34th state on January 29th, 1861, about 2 ½ months before the Confederate assault on Fort Sumter that marked the beginning of the Civil War. The 34th star was officially added on July 4th of that year, but most flag makers would have added a 34th star with the addition of KS in Jan. The star count remained official until July 4th, 1863, and 34 star flags would have been produced until the addition of WV in June of that year. In summary, due to the rarity of issued and identified Civil War cav. guidons, the associated history, the beautiful circular star configuration, the single-family ownership, and the small but bold and easily displayable size, this is one of the best, Union army, Civil War guidons that has ever been offered at auction. Only three issued guidons with the company letter gilt-painted in the center of the star field have come up for public sale in recent years. Among them, only this single flag retains such fantastic associated history and the associated items belonging to the soldier who took them home and managed to preserve the artifacts for future generations. This fabulous guidon together with the rare bugle and all the other associated items make for a superb historical grouping which could easily be the centerpiece of any Civil War collection. The guidon is typical of those used by Union troops. Its stripes and canton are of finely hand-sewn silk, while the company letter and the wreath pattern of stars that surrounds it are gilt-painted. The sleeve is created by folding back a section of the stripes and canton over a lining of fabric used for reinforcement. This was formerly finished with treadle-stitching. The staff would slip directly through this open portion if the hoist. SIZE: Item – 27″ x 35.5″ (flag), 6” x 16” + tassel (bugle), 11.25” x 9.5” (photo), 8.5” x 11” (discharge papers); Frame – 37″ x 45″ (flag), 21” x 27” (bugle), 15.25″ x 13.5″ (photo), 15.25″ x 13.5″ (discharge papers) CONDITION: Flag has been pressure mounted in an archival manner behind u.v. protective acrylic. It was then placed in an unusually large gilt frame of the 1830-1860 periods. Bugle and sash were stitched to 100% black cotton twill laid over archival materials. A deep shadowbox was created behind u.v. glass using a period gilt frame with similar the same general coloration. Albumen photo and discharge papers were also framed in an archival manner behind u.v. glass, using matching, period gold gilt frames. Flag is quite complete, but like most silk battle flags, there has been some fabric loss. Flag is brittle and there are many separations. Red stripes have experienced significant fading. Very small amount of clear tape present on the stars. Letter “I” became partially separated and was, at some point, mended with hand-stitching. Overall condition is commensurate with the flag’s construction and use and is similar to other surviving examples. 4-32852(50,000-75,000)

FLAG FROM ADMIRAL FARRAGUT’S SHIP AT FORT MOULTRIE, SOUTH CAROLINA IN 1861. This once large silk flag is now in pieces in an 18” x 12” shadowbox that is 4” deep. Flag and fringe almost completely fill this box. As can be seen in photographs, this would be quite a restoration project; however, the flag, as is, displays quite nicely with a wonderful GAR tag. Tag reads, “This flag was on Admiral Farragut’s ship at Fort Moultrie, SC at the beginning of the Civil War. Presented to Dyer’s Post, January 31, 1891, by Col. Peirson of Painesville, Ohio.” There is some biographical material on Col. Peirson and his wife included with this lot. What a chance to own a piece of Naval history from the single most famous American Civil War Naval commander! CONDITION: Colors are bright. Flag was not removed from box for study; however, silk fragments appear sound. 8-76211 JS277 (3,000-5,000)

REGULATION CAVALRY GUIDON OF COMPANY D, 4TH VIRGINIA U. S. CAVALRY, PAXTON GUARDS. This rarely seen dragoon pattern (Model 1833) guidon was carried by Company D, 4th VA Cavalry, recruited as the “Paxton Guards” in honor of Col John C. Paxton, 2nd VA Cavalry, whom Gen. J. D. Cox described as “handsome, dashing, fearless . . . a bold rider and daring scout.” This company was raised between the Ohio River cities of Parkersburg and Marietta during Morgan’s Raid in the summer of 1863. Over the next six months its men experienced constant escort and scout duty in the cold, barren mountains of WV, clashing with Confederates at Salt Bridge, Medley, and Williamsport. In early March 1864 it mustered out of U. S. service with many members re-enlisting in other regiments. Guidon is fabricated of remarkably resilient silk of white under red panels, which has faded to a light purplish hue. Signature of sign/flag painter “TURTON” appears immediately beneath the third line of his work: “PAXTON GUARDS / Co. D. / 4th VA. CAVALRY.” Gold leaf lettering is professionally restored, expertly following their orig outlines. On hoist, minute areas of worn silk reveal red wool-worsted cording, similar to regulation artillery hat cords. Entire guidon is pressure-mounted in an archivally-prepared frame. Southeastern Ohio residents remember Jerry Devol, Washington County historian, who originally owned this guidon which was descended from 1st Lieut. William L. Theis, Paxton Guards. When Jerry returned from the Korean War, the flag had vanished until another collector rediscovered it decades later—this time in a Parkersburg antiques store, buried in a bag of old silks. It rejoined Jerry’s collection and was resold in the Devol estate auction in June 1997 and is now being offered again. The flag for the first time is now fully archivally conserved and framed by the Intermuseum Conservation Association of Cleveland, OH. A detailed conservation report and history of Paxton and the Paxton Guards accompany this lot along with a 19th century engraving of Col. John C. Paxton. CONDITION: Very good as conserved and restored. Detailed conservation report is available for interested bidders. 8-76210 JS246 (25,000-35,000)

RARE EARLY 1861 CIVIL WAR PATRIOTIC FLAG. This flag, about 45” on hoist and about 78” long, shows much wear and deterioration, though we believe it would conserve and present quite nicely. One stripe reads “Liberty and Union” and the white stripe beneath it reads “Washington”. Canton, approx. 25” square, exhibits painted eagle with ribbon with “E Pluribus Unum” above blue panel of thirteen 2-1/2” gold painted stars. Surrounding eagle are an additional twenty 1” gold painted stars, which make a total of 33 stars—the correct number of stars for the beginning of the Civil War in 1861. Blue and red tasseled ties that would have attached this flag to a staff are typical of the patriotic fervor early in 1861. The flag has seen use as seen by the stitched repair in eagle on canton. This flag, with proper conservation, could be a centerpiece of many collections. CONDITION: About ½ of the material white stripes is missing. Red stripes have moth damage. Canton has numerous separations, but painted device is mostly intact. Motto on the 2 stripes is missing several letters or partial letters. 8-76212 JS249 (7,500-27,500)

Revised: 10/19/2007

DESCRIPTION SHOULD READ:

EXTREMELY RARE OFFICIAL PRESIDENTIAL FLAG OF 1902. In 1901 it came to the attention of President of Theodore Roosevelt that there were two official versions of the presidential flag; one with a red background used by the Army (of more recent design) and one with a dark blue background used by the Navy (an older design). As there were two totally different presidential flags, it created obvious confusion and a decision was made to utilize only one design for the President and since the Navy was the older of the two, Roosevelt opted to use their design. It was decided, at this time, that the field would be blue rather than red, that an additional change involved the color of the eagle. The normal natural colors (i.e. brown, etc.) for the eagle’s body, made the design far more difficult to distinguish at a distance. Therefore, it was elected that the body of the eagle be white so that it stood out more dramatically against the blue background and was easier to distinguish at a distance. This rare example, consigned by the grandson of the original owner Michel D. Schaefer, was given to Schaefer at his retirement sometime during WWII, during which time Schaefer provided extremely valuable Naval architect and design services for the development of aircraft carriers. Schaefer also participated in the design of this very flag during Teddy Roosevelt’s administration. According to the grandson, his grandmother told him on various occasions (the consignor’s grandfather died when he was a young boy), that F.D.R. himself presented the flag to Schaefer and indicated that this exact flag had been used by his cousin Theodore Roosevelt when he was president. This flag is beautifully silk embroidered, is 43-1/2” on hoist and 61-1/2” on fly. The hoist is embroidered “President’s Standard No. 6 / NY, NY, Sept 1902”. The device on this flag of eagle with constellation of stars was adopted on November 12, 1901, according to accompanying period copies of original correspondence. President McKinley had just been assassinated two months earlier, and Theodore Roosevelt, our new President, enacted this new Presidential flag. The flag is a Navy flag. The number “6” refers to the size of the flag and “NY, NY” refers to Navy Yard, New York not New York, New York. As a result of research and various conversations with some of the nation’s leading vexiollogists, the consignor states that because of its silk construction and the grommet placement that this was a flag used inside a building rather than the outside. He further states that there were actually three of this size and design used in Teddy Roosevelt’s administration; one in the office of the President, one at the entrance of the White House and one at the War Department. Our consignor further states that this exact flag is believed one of those three and the only one currently known to him in existence. This design remained in use until Woodrow Wilson’s administration when it was again changed and thus this design was used for a relatively short period of time. Accompanying this lot is an affidavit from the grandson of Michel Schaefer, reaffirming much of the information listed above. Also accompanying this lot are numerous copies of period government documents relating to the need of a single presidential standard and the enactment and details relating to that. Also included is a copy of the obituary for chief clerk, Michel D. Schaefer and a copy of his certificate of death. This was a governmental flag and as such, would under normal circumstances never appear for public sale and the fact that this President’s official Presidential flag is of a rare design that existed for only a short period of time makes this an even more rare opportunity to own an official, genuine “Great Seal” American Presidential standard. CONDITION: Silk embroidery is very good. Period colors are strong. Silk has numerous cracks and separations at folds, but could be conserved. For display and safety purposes the flag is currently framed under Plexiglas. 4-31117 (10,000-20,000)

UNIQUE AND HISTORIC CAPTURED CONFEDERATE BLOCKAGE RUNNER’S PENNANT, FROM CHARLESTON HARBOR. One of the nicest relics of the Blockade Runner action during the American Civil War is this identified ship’s pennant in superb condition. An individual or company used these pennants, mostly of commercial origin, to identify their ships and their ownership. They were distinctive in nature and many fine art depictions of blockade-runners during the American Civil War show these colorful and large pennants streaming from the mast. This example is identified on the canvas-reinforced hoist in period ink reading: TAKEN FROM A BLOCKADE RUNNER, CHARLESTON HARBOR, S.C. 1864. In my view, this inscription is completely authentic and the construction of this pennant is consistent for its period of use. The pennant, long and triangular in shape, measures 150” long and stands 32” tall at the hoist. It is made of high quality white wool bunting, sewn in two horizontal pcs, with a large red wool oval positioned in the center of the pennant measuring 13” X 18”. The hoist is reinforced with a folded canvas strip with its rope inserted. This pennant represents an interesting and rare Confederate war souvenir. The Union Blockade of the seacoast of the United States was authorized by President Abraham Lincoln in April 19, 1861. The Union Navy maintained a massive effort on the Atlantic and Gulf Coasts of the Confederate States of America designed to prevent the passage of trade goods, supplies, and arms to and from the Confederacy. Ships that tried to evade the blockade, known as blockade-runners, were mostly newly built, high-speed ships with small cargo capacity. They were operated by the British (commercially) and ran between Confederate-controlled ports and the neutral ports of Havana, Cuba; Nassau, and Bermuda, where British suppliers had set up supply bases. During this operation Lincoln commissioned 500 ships, which destroyed or captured about 1,500 blockade-runners over the course of the war; nonetheless, five out of six ships evading the blockade were successful. CONDITION: Excellent. Colors are bright. Flag shows little wear and, other than scattered holes throughout, presents a wonderful, rare and attractive Confederate associated flag. 4-30365 JL15 (2,000-4,000)

38-STAR AMERICAN FLAG. 38 stars commemorate the state of CO in 1876. This flag was used until 1890. Flag frame is approx. 26” x 18”. Flag appears doubled under on fly and is probably longer. Construction appears all hand-sewn. Though flag was not removed from frame, stripes appear to be wool blend; stars and canton cotton. Flags of this petite size are always popular, and this one displays nicely. CONDITION: Flag appears very good overall. About 1-1/2” repaired hole is visible on top stripe near fly end. Scattered mothing is seen on stripes. 4-32893 JS248 (300-500)

SPANISH AMERICAN WAR ERA FLAG OF COMPANY I, 7TH NEW YORK NATIONAL GUARD. This flag, about 38” on hoist and 52” on fly, is made of white wool bunting with “SEVENTH REGIMENT/ Co. I / N. G. S. N. Y.” in sewn-through blue silk letters between 6” and 9-1/2” tall. Also accompanying this flag is a photograph from the estate of Capt. John Gould of the 7th Regiment, showing him and other officers in front of a tent. Photograph by Poch Bros., of 935 Broadway, New York, is dated 1891, is framed and measures approx. 15” x 11”. CONDITION: Hoist and body of flag are sound; however, silk lettering has tears and losses in several of the letters, as can be seen in photos. 4-31594 JS252 (1,000-2,000)

PAIR OF 34 AND 35 STAR FLAGS. These two flags are made by the same hand, the 34 star flag being 31″ x 57″ and the 35 star flag being about one half that size measuring 16″ x 28″. Stripes are machine sewn, stars on canton are hand sewn. Only one side of these flags is finished as can be seen in photographs. 34 stars commemorate the state of Kansas when it entered the Union in 1861. 35 stars commemorate the state of West Virginia when it entered the Union in 1863. The cantons of each flag are beautifully designed with the central star surrounded by two rings of stars and individual stars in each quadrant. These flags would frame nicely and add to any decor. CONDITION: Overall both flags are in good condition with good colors with only light soiling and some yellowing on white from age. 4-32695 JS308 (2,000-3,000)

Revised: 10/19/2007

CORRECT DESCRIPTION SHOULD READ:

RARE CIVIL WAR ERA US MODEL 24 POUNDER 1844 FLANK HOWITZER. This cannon made by Cyrus Alger & Company of Boston, Mass. in 1847 could have seen use in both the Mexican and Civil Wars. This particular cannon was recently discovered near New Orleans and is in beautiful condition. These cannons were generally used at Forts where land attack was possible. These cannon manned many American and Confederate forts prior to and during the Civil War. Forts where these cannon were used (and some still survive at these forts) include Ft. Morgan, Mobile; Ft. Pulaski, Savannah; Ft. Hamilton, New York; Ft. Washington, Maryland; Ft. Sill, OK; Ft. Montgomery, New York; Ft. Jefferson, Florida; and many others. These cannon were effective for over 20 years and were manufactured into the Civil War by both Union And Confederate foundries. Cyrus Alger made 300 such cannon between 1846 and 1849, this is sr. # 141, one of the few surviving in private hands. This is only the 2nd Model 1844 Flank Howitzer we know of sold at public auction. Accompanying this cannon is a fine condition 24 pound projectile that was excavated on the Port Hundson, Louisiana battlefield where many such cannon balls are found. This cannon would mount beautifully on a carriage and would be the focal point of any collection. Cannon is marked on right trunion “C.A. & CO.” It is 69” long x 11-3/4” across muzzle which is marked “141” and “JWR” for James Wolfe Ripl;ey, Chief of American Ordinance. It has a 5-3/4” bore and is about 14” diameter at back end. The trunions & cascable are 4-5/8” diameter. About 4-1/2” from rear edge is a shallow depression with a flash hole. On front edge of step, just forward of trunions, on the top of bbl, is stamped “US”. CONDITION: Extremely fine. Currently in black paint with lightly worn & chipped edges. A rare & desirable Civil War era cannon. 8-76225 JR609 (30,000-40,000)

Revised: 10/19/2007

(Additional Information) Please note the inscription referred to on the top of the cannon barrel is an Ottoman Turkish inscription.

FANTASTIC CARVED, GOLD INLAID ISLAMIC CANNON. This 37” bbl. has a bore of 1-1/4”. It is overlaid with gold at the breech & muzzle with Moorish or Islamic designs followed by a long inscription. It is mounted on a 88” wooden carriage with camel legs as the front tripod & a fancifully carved dolphin as the tailstock. The carriage around the barrel is carved with vine & leaf engraving with shell carving at the pivot point. It has a paper museum tag on the left side along with an engraved metal museum tag engraved “taken at the storming of St. Jean De Acre / November 5th 1840. Accompanying papers detail the battle of St. Jean De Acre during the campaign, including maps & a history of the entire war. After its capture it was taken to London where it was displayed at the United Service Museum in Whitehall until 1894 when it was moved to their banqueting hall. In 1962 the collection was dispersed & the cannon was moved to a museum in Pennsylvania. The cannon actually dates to around 1700, it has a Damascus barrel, & the literal translation of the inscription on top reads “Outpourings of my groans roar in the bosom of the heavens like rumblings of thunder. The fire of your love makes towers of the enemy moan.” Twenty two ships, 17 of them British attacked the fort & capture it in a short time, the city of Acre was captured by the Israelie Army in 1948 & has been ruled by them since. CONDITION: Even brown patina on the barrel, the stock/carriage shows minor wear on the legs but little ware elsewhere. This makes a great display piece & would be unique in any Islamic, Cannon or Military collection. 4-31089 FS266 (25,000-35,000)

EXTREMELY RARE CIVIL WAR HALE ROCKET LAUNCHER. Rare & unusual Civil War implement, the first one ever encountered by this cataloger. It is an iron tube about 58-1/2” long with a 2-3/4” bore. The rear 14-1/4” are cut away, apparently to allow access for loading & ignition. It has a base plate with two short feet and a trunion ring 4” from muzzle with angled holes in the trunnions with locking screws for two 5/8” steel rods that are 36-5/8” long. Elevation adjustment was problematical at best, but it had a rudimentary rear sight which is articulated just above the cutout for crude aiming. Tube & iron rods are in old, olive-drab paint. This fired the 2-1/4″ to 2-1/2″ rockets. At 47 degrees elevation, the ranges were 1760 and 2200 yds for shot, shell and case. Rockets were used very little by either side during the Civil War while occasional mention of use is found in the Official Records of the War of the Rebellion. They were fired during the Battle of Seven pines Virginia and Charleston, SC. CONDITION: Very good, but missing inertia counterweight on sight elevator. Retains about 80% dark olive-drab paint with soil and nicks & dings. 4-32586 JR610 (15,000-25,000)

REGULATION CIVIL WAR INFANTRY EAGLE DRUM. This regulation eagle drum is 16-1/2” in diameter and 15-1/2” tall. All parts are orig and authentic. Label inside drum reads “C & F Soistmann / Manufacturers of all kinds of drums / No. 458 Dillwyn Street / Philadelphia”. Conrad and Frederick Soistmann are listed as drum makers at this address in 1863. This manufacturer had a contract with the Army in 1864 for 1,000 drums. Painted eagle on this drum is excellent with only minor losses of paint, as can be seen in photograph. Most of the orig tensioners are missing; however, the rope is orig and solid. Bottom head is badly shattered. Top head is solid but warped. This is a beautiful, untouched, Civil War eagle drum that would be hard to upgrade CONDITION: Very good overall as described above. Top rim fits loosely. 8-87530 JS270 (8,000-12,000)

PRE-CIVIL WAR NEW YORK MADE SNARE DRUM. This drum is 14-1/2” tall x 16-1/4” in diameter. Label inside drum reads “Albany Drum Factory, Military and Bass Drums / Made and Sold / by J & H Meacham, No. 104 State Street, Albany”. Wood body is decorated with tacks around vent hole. Drum has been restored, utilizing new ropes and tensioners. Apparent orig heads have been reinforced. This drum would display very nicely and make a fine small table in any living space or gun room. CONDITION: Good as restored. 4-31600 JS269 (450-750)

RESTORED DRUM OF L. B. STRATTON OF THE 89TH NEW YORK VOLUNTEER INFANTRY. This snare drum, 15” in diameter x 10” tall, was rebuilt and refinished in Oxford, New York in 1918 by Howard C. Bartlett, and is so written inside drum. An orig, Civil War, patriotic label is not easily discernible. Written on top head is “L.B. Stratton/August 4, 1864” along with partial regimental information “89th. . C. (or G.?) Bower (or Bowers?)”. The family who consigned this drum is directly descended from the restorer of the drum, who lived in Oxford, N.Y. Consignor surmises as follows: “According to New York in the War of the Rebellion, 3rd Ed, by Frederick Phisterer (J.B. Lyon, 1912), the Hon. J.S. Dickinson received authority, August 29, 1861, to recruit a regiment of infantry; this regiment (the 89th) was organized under Col. Harrison S. Fairchild and Lieut.-Col J.C. Robie, at Elmira November 26, 1861, and there mustered in the service of the United States for three years December 4, 5 and 6, 1861. At the expiration of its term of enlistment those entitled thereto were mustered out, and the regiment retained in service. During its service the regiment lost by death, killed in action, 4 officers, 49 enlisted men; of wounds directly received in action, 2 officers, 52 enlisted men; of disease and other causes, 1 officer, 158 enlisted men; total, 7 officers, 259 enlisted men; aggregate, 266; of whom 13 enlisted men died in the hands of the enemy. The 89th was in siege operations against Petersburg and Richmond from June 16, 1864, to April 2, 1865. This encompasses the date inscribed on the drum head (4th Aug 1864). A Gilbert (G.) Bowers, who was a mason, served in Company E of the 89th Regiment. He enlisted at age 43 at Oxford for three years and mustered in as a private on Jan. 4, 1864. He was discharged on May 26, 1865 at Stuart Hospital in Richmond, Va. and filed for a military pension March 25, 1867. The name on the drum that is more legible is L.B. Stratton. We suspect (but have not yet been able to confirm) that this is actually Whitman Stratton, who also served in Company E of the 89th. Whitman Stratton (also Straton), was mustered in as a private in Co. E on October 7, 1861. He was promoted to sergeant (no date available), was discharged on October 7, 1864, and applied for a military pension on July 2, 1890. CONDITION: Very good as restored; slight tear in bottom drum skin.. 4-31591 JS268 (1,000-2,000)

PRE-CIVIL WAR NEW HAMPSHIRE ROPE-TENSION SNARE DRUM. This is a very nice, orig, late 1850s-style, American, plain-sided, maple, rope-tension snare drum with an orig affixed label for a well-known Concord, NH manufacturer. Drum is 17-1/4” tall x 16-1/2” wide. There are no decorations painted or otherwise applied to the exterior of the drum shell. It has bright red drum hoops. Drum has on orig period label fixed to the interior of the drum shell body that has been covered with a clear, acid-free sheet as part of the restoration/preservative process. Period printed label reads, “Bass & Tenor Drums / Ebony Drum-Sticks / B & C Fifes / Manufactured / and for sale by / Porter Blanchard / Concord, New-Hampshire”. This drum was restored (new antiqued ropes and leather tighteners, repainted orig hoops) by William Reamer of Lancaster, PA, in 2004, and is marked as such on the interior. This drum would add charm and display very nicely in any living space or gun/collection room. CONDITION: Good. 4-32932 JS267 (700-1,000)

CIVIL WAR PERIOD ROPE-TENSION SNARE DRUM, BOSTON, MASSACHUSETTS. This is a very nice orig American Civil War, plain-sided, maple, rope-tension snare drum with an orig affixed label for a Boston manufacturer. Drum is 14-1/2” tall x 17-1/4” wide. There are some hand-painted gold letters applied to the exterior of the drum shell, but due to the style of lettering, it is uncertain as to their exact signification. These appear to be “J. H. F.”. Drum has an orig period label affixed to the interior of the drum shell body that has been covered with a clear acid-free sheet as part of the restoration/preservative process. Hand-lettered ink paper label reads “Made by White Brothers / NO. 86 Tremont Street / Boston Mass / 1859”. In American Military Goods, Dealers and Makers, p. 172, the authors show a listing for Ira E. White, Boston drum maker from 1864-1865. This drum was restored (new antiqued ropes) by William Reamer of Lancaster, PA, in 2004, and is marked as such on the interior, “Restored by W. H. Reamer / 5-3-04”. Mr. Reamer is a widely recognized drum manufacturer/restorer. This drum would add period charm and display very nicely in any living space or gun/collection room. CONDITION: Very good as restored. 4-32931 JS266 (450-750)

EARLY FRENCH DRUMMER BOY JACKET. This outstanding, colorful coat is purportedly an extremely rare French Rev. drummer boy’s coat. According to a former owner, it was purchased at a New England auction a few years back during the dismantling auction of an old museum where it purportedly was represented as a French Rev. drummer boy coat. The coat of red, white & blue wool is hand-sewn and is fitted with a pr of epaulets having 2 pewter colored buttons. The frontlet, with 14 identical pewter colored buttons, the pocket flaps each fitted with 3 identical pewter colored buttons of a larger size, the cuff of each sleeve fitted with 2 identical pewter colored buttons (2 others are missing), and the back above the split with 1 lrg pewter colored button identical to the rest (1 missing). The buttons are ornamented with a bugle, a flame and “Liberte Ordre Public”. Some of the buttons with that and others with similar bugle & flame relief decoration & “Garde Nationale”. SIZE: Approx. 30″ from top of collar to tip of tail. CONDITION: Mild scattered mothing. most of which is on the interior of the coat. Overall soiling and 2 hooks for holding epaulets missing. A wonderfully graphic and diminutive uniform. 8-87557 JJ3001 (5,000-10,000)

COLORFUL PATRIOTIC OR POLITICAL PICTURE FRAME. This graphic late 19th or early 20th C. wooden frame was apparently made for either political campaigns or perhaps a GAR frame. Shield-shape with deep blue field and 13 ivory stars and 13 alternating red & white stripes. An oval opening in the center would serve as a display for the image of the candidate or veteran. The reverse of the shield, below & above the oval, have wood plates with a groove to slide the image in. The top wood plate drilled with 5 holes to hold small flags. This would be an outstanding display frame for an appropriate military or political image. SIZE: 23-1/2″ high x 18″ wide. CONDITION: Scattered small paint loss. Gold over-painted long ago. Nice old patina. 8-87558 JJ3000 (1,500-2,500)

RARE SHARPS NEW MODEL 1859 3-BAND RIFLE WITH BERDAN SHARPSHOOTER REGIMENT ATTRIBUTION. SN 56113. Cal. 52. Fine 3-band rifle with 30″ rnd bbl, square base front sight/bayonet lug with Lawrence Patent ladder rear sight & standard Sharps markings on bbl, receiver & lockplate. Receiver has dbl set triggers and it falls in serial range of known Berdan Sharpshooter rifles. Mounted with very highly figured burl walnut buttstock with legible “JT”, for John Taylor, cartouche on left wrist & small “T”inspector mark on left side of bbl. It has std rnd forearm with spring band keepers and sling swivels with normal Sharps buttplate. It has a steel 2-pc patchbox in right side of butt. Berdan’s Sharpshooters were organized in late 1861 by Col. Hiram Berdan and after much wrangling with The Ordnance Dept., 1,000 Sharps rifles were ordered in Jan. 1862 with the order being increased to 2,000 in Feb. 1862. Col. Berdan contacted Sharps Co. and requested them to modify the contract to supply dbl set triggers to which they readily complied. When the Chief of the Ordnance Dept., learned of this from his inspectors, he immediately ordered the company to stop abridgment of the contract which was done after only about 500 of the dbl set trigger rifles were completed. Balance of contract of 1,500 rifles was furnished with sgl triggers. Reference: Sharps Firearms, Sellers. Accompanied by a copy of Sharpshooter: Hiram Berdan, his famous Sharpshooters and their Sharps Rifles, Sword, wherein this exact rifle is pictured on pp. 91-92 and is listed on p. 98 as being a surviving Sharps Berdan rifle. PROVENANCE: Wiley Sword Collection. CONDITION: Very fine. Traces of orig blue & case colors remain in sheltered areas with bbl retaining mostly a mottled silver brown patina over most of exposed bbl with a strong plum/blue patina around rear sight. Receiver & lockplate are mostly a silver/gray patina with some scattered light surface spotting. Stock & forearm are sound with usual nicks & dings with stock retaining a cleaned, hand worn patina and forearm a dark, hand worn patina. Mechanics are fine, strong bright bore with light to moderate pitting. 4-32576 JR444 (12,500-17,500)

RARE & AUTHENTIC SHARPS NEW MODEL 1859 3-BAND RIFLE WITH BERDAN SHARPSHOOTERS ATTRIBUTION. SN 56293. Cal. 52. Fine 3-band rifle with 30″ rnd bbl, square base front sight/bayonet lug with Lawrence Patent ladder rear sight & standard Sharps markings on bbl, receiver & lockplate. Receiver has dbl set triggers and it falls in serial range of known Berdan Sharpshooter rifles. Mounted with straight grain uncheckered American walnut buttstock. It has small “OWA” inspector initials for O.W. Ainsworth on left side of bbl. It has std rnd forearm with spring band keepers and sling swivels with normal Sharps buttplate. It has a steel 2-pc patchbox in right side of butt. Berdan’s Sharpshooters were organized in late 1861 by Col. Hiram Berdan and after much wrangling with Ordnance Dept., 1,000 Sharps rifles were ordered in Jan. 1862 with the order being increased to 2,000 in Feb. 1862. Col. Berdan contacted Sharps Co. and requested them to modify the contract to supply dbl set triggers to which they readily complied. Chief of Ordnance Dept., learning of this from his inspectors, immediately ordered the company to stop abridgment of the contract which was done after only about 500 of the dbl set trigger rifles were completed. Balance of contract of 1,500 rifles was furnished with sgl triggers. Reference: Sharps Firearms, Sellers. Accompanied by a letter from Wiley Sword clarifying some previous erroneous information regarding the triggers on this rifle. On p. 99 of his book, Sharpshooter: Hiram Berdan, his famous Sharpshooters and their Sharps Rifles this specific rifle is listed as having a sgl trigger when in fact it has dbl set triggers. PROVENANCE: Joe Marino; Monte Whitley CONDITION: Fine. Bbl retains a smooth, even, very dark brown patina with receiver, lockplate & all other metal a medium mottled silver/brown patina with fine pitting on lever. Forearm has a couple of repaired cracks in lower section & a hairline in wrist, otherwise wood is sound and retains a smooth, hand worn patina with possibly some very old finish having been wiped over the oil finish. Mechanics are fine, strong bright bore with light to moderate pitting. 4-32577 JR445 (6,000-10,000)

RARE TRANSITION COSMOPOLITAN TO GWYN & CAMPBELL MONKEY TAIL TYPE I CIVIL WAR CARBINE SN 10. Cal. 52. Standard configuration with 20” oct to rnd bbl, pinched blade front sight with long base ladder rear sight. Left side of box-like receiver has a staple & ring with right side having a long lockplate with serpentine shaped hammer. Lever is long & serpentine shaped with a bayonet type lever catch in rear loop. Mounted with straight grain, uncheckered American walnut buttstock without forearm and has a semi-crescent buttplate. About 4,200 of this type carbine were produced for the Union Army. The Gwyn & Campbell is simply a continuation of its predecessor, the Cosmopolitan carbine, owned by same two men and made in same factory. There is no indication that they were retained after Civil War & used in Indian Wars. This very gun is an extremely rare transition example from the Cosmopolitan to Gwyn & Campbell. Only a few are known. This exact gun is pictured on pg 47 of Tom Rentschler’s book of Cosmoplitan & Gwyn & Campbell carbines. CONDITION: Good, all matching. No orig finish remains being a thin gray/brown patina with moderate pitting in front of nipple on bbl and on top of breech block. Stock is sound with a couple of minor dings and retains most of an old applied oil finish. Mechanics are fine, strong bright bore with some minor roughness in grooves. 4-32811(6,000-7,500)

SCARCE JOSLYN MODEL 1855 MONKEY TAIL CARBINE SN 4N. Cal. 54. Fine early cav. carbine with 22” rnd bbl, pinch blade front sight with Henry style 800 yard ladder rear sight. It has an unusual breech loading system with a long top tang that has a sliding ring at rear end which, when slid forward, allows breech lever to be raised for loading. It has usual markings on breech lever & lockplate. Mounted in a 1-pc straight grain walnut stock with brass bbl band, 2-pc brass trigger guard & brass carbine buttplate. Sling bar & ring are mounted on left side panel. Only about 1,500 of these were made in period 1855-56 with 1,200 of them sold to the Government, Flayderman’s Guide to Antique American Firearms. Flayderman’s also states that a number of these were issued to Ohio Cavalry units. CONDITION: Fine to excellent with bbl retaining 95%+ orig lacquer brown finish. Vice marks just in front of forestock tip. Breech lever, receiver, lockplate & hammer retain dark orig case colors. Brass is a medium mustard patina. Stock has sharp edges with handling dings & a few scratches. Mechanics are fine, very bright shiny bore with scattered pitting just in front of chamber area. 4-32608(7,000-9,000)

FINE BURNSIDE 5TH MODEL SADDLE RING CARBINE SN 11992. Cal. 54. Standard late Burnside with 21” rnd bbl, pinched blade front sight and two position flip rear sight graduated to 500 yard. Top of bbl is marked “CAST STEEL 1864”. Top of receiver and lockplate have usual markings. It is mounted with straight grain, uncheckered American walnut with small rnd forearm and single band with spring keeper and straight stock with carbine buttplate. Bottom of stock has a sling swivel and left wrist has two clear legible cartouches with small inspector initials on various parts. Right side of stock has two crudely carved initials “JH”. Left side receiver has sling bar and ring. This was a very popular carbine during the Civil War with several thousands made in the period 1863-65. They were issued to a variety of cavalry units and used effectively by the troops. It is unknown whether they survived the Civil War to be used in the Indian Wars on the frontier. CONDITION: Very fine. Bbl retains about 90% original blue with some thinning and a few minor nicks. Receiver and lockplate retain most of its original case colors, moderately faded. Breechblock retains about virtually all is bright original blue. Lever and hammer retain original case colors in sheltered areas being mostly a gray-brown patina. Wood is sound with light handling and use marks in the stock with a series of bruises on the forearm and carries a dark hand worn, oiled patina. Mechanics are crisp, brilliant shiny bore. 4-32602 JR521 (2,000-3,000)

RARE FIRST TYPE MERRILL CARBINE WITH STAPLE FRONT SIGHT SN 270. Cal. 54. Very early production with 22” rnd bbl with very unusual & rare U-shaped staple front sight and a 3-leaf carbine rear sight graduated to 500 yards. It has usual breech lever markings with maker’s name & patent number on lockplate in front of hammer & serial number vertically behind hammer. It has brass furniture and is mounted in 1-pc straight grain, uncheckered American walnut stock with 2-pc patchbox on right side. This was a fairly popular carbine in Civil War with a total of over 14,000 having been manufactured & issued to a number of famous hard fighting units. No doubt this, being one of first produced, was issued and saw service throughout most of Civil War. It has the second type copper faced breech plunger which acted as a gas seal for percussion cartridge. PROVENANCE: From Bill Moore’s collection, #270, pictured in his book on Merrills, extremely rare. CONDITION: Fine. No orig finish remains with metal being a mottled gray/brown patina with some fine surface pitting and a couple of cuts on top of bbl that could be sword or knife strikes. Stock has a repaired crack in wrist, otherwise is sound with minor nicks & scratches and a couple of small gouges and retains most of a professionally restored finish. Mechanics are fine, strong bore with heavy pitting. 4-32813 JR520 (7,500-10,000)

CIVIL WAR SMITH CARBINE SN 3579. Cal. 50 RF. Marked on left side of frame “American Machine Works” and “Poultney & Trimble”, this carbine has 21-5/8” oct to rnd bbl with broken dovetail front sight and a tiny carbine ladder rear sight. It has a sling bar, missing ring, on left side of receiver & tiny “LFR” inspector initials on left flat of bbl. Mounted with straight grain, uncheckered American walnut with small rnd forearm & sgl band with straight stock & carbine buttplate. There is a clear cartouche on left wrist. CONDITION: Fine. Bbl, with its broken front sight, retains a strong blue/brown patina that may clean much better. Latch spring on top of bbl is apparently weak and has a fine blacksmith riveted support. Receiver retains case colors in the most sheltered areas, mostly on right side, with balance a mottled silver/gray patina. Trigger guard retains about 80% orig blue. Stock has a hairline in left side of wrist, otherwise wood is sound with a few nicks & gouges in forearm and light handling & storage marks in stock and retains 30-40% orig finish under an old hand worn patina. Mechanics are fine, bright shiny bore with a ring about mid-point. 4-32777 JR516 (2,000-3,000)

CIVIL WAR SMITH CARBINE SN 10793. Cal. 50 RF. Marked on left side of frame “American Machine Works” and “Poultney & Trimble”, this carbine has 21-5/8” oct to rnd bbl with dovetail front sight with German silver blade and a tiny carbine ladder rear sight. It has a sling bar and ring on left side of receiver & tiny “LFR” inspector initials on left flat of bbl. Mounted with straight grain, uncheckered American walnut with small rnd forearm & sgl band with straight stock & carbine buttplate. There is a clear cartouche on left wrist. CONDITION: Fine to very fine. Bbl retains about 80% strong blue/brown patina with blue in very sheltered areas. Latch spring on top retains about 85% bright blue. Receiver has strong case colors on right side in sheltered areas with balance a cleaned gray metal color. Wood is sound with minor handling & storage marks and retains most of an old restored finish. Mechanics are crisp, brilliant shiny bore. 4-32621 JR517 (2,000-3,000)

VERY RARE IDENTIFIED & DOCUMENTED SPENCER REPEATING RIFLE USED BY 6TH OHIO SHARPSHOOTERS SN 2240. Cal. 56-56. This extraordinarily rare rifle has 30” rnd bbl, square base front sight with German silver blade & standard 800 yard Spencer ladder rear sight with tension spring. It has three bands with sling swivels and is mounted with straight grain, uncheckered American walnut with full length forearm & straight stock with standard Spencer buttplate. There are two small tacks in top of wrist, purpose of which is not known. There is a screw hole on bottom of wrist on left side by trigger, apparently where a wood screw was inserted to relieve pressure on sear thereby allowing a lighter trigger pull to increase accuracy. This rifle was issued to and carried by Pvt. Jacob Neff of the 6th Independent Co. of Ohio Volunteer Sharpshooters. Pvt. Neff enlisted on Nov. 8, 1862 at age 25. He was mustered out with his unit on July 19, 1865 in Nashville, TN. His muster-out document dated the same date discloses that he retained his Spencer rifle & accouterments, complete, under Special Order #101 War Dept. 1865 and was charged $10.00. Private Neff’s company of sharpshooters spent their entire military service in the Dept. of the Cumberland under Gen. Rosecrans & Gen. Thomas and participated in a number of battles in that region including the Atlanta Campaign. The 6th was known as “Thomas’ Bodyguards”. Accompanied by numerous copies of official records from The National Archives including the list of arms & accoutrements of the 6th Company Ohio Volunteer Sharpshooters. Jacob Neff is listed as having been issued a Spencer rifle #2240 and accoutrements. Also included are Pvt. Neff’s muster rolls & pension papers. This is truly a rare opportunity for the advanced Civil War Collector to add a positively identified & documented sharpshooter rifle to their collection. CONDITION: Very good. No orig finish remains on bbl or bands being mostly a smooth dark brown patina. Receiver, hammer & lockplate retain traces of case colors with balance turned silver. Wood is sound with nicks, scratches & dings showing heavy wear. Mechanics are fine, strong bore with moderate to heavy pitting. 4-32833(5,500-6,500)

SPRINGFIELD ALTERED SPENCER CARBINE. SN 18945. Cal. 50 RF. SN 18945. Post Civil War Springfield alteration with 20”, 3-groove bbl and Stabler cutoff. It has a square base front sight with a standard Springfield ladder rear sight with tension spring and a musket slide added. It has a sling bar & ring on left side. Mounted with nicely figured uncheckered American walnut with small rnd forearm, sgl band with sling swivels & straight stock with clear “ESA” cartouche on left wrist. CONDITION: Very fine. Bbl retains a thin blue/brown patina with some slight surface discoloration on bottom. Receiver, lockplate, hammer & buttplate retain most of their orig dark case colors. Lever & bottom tang are a silver patina from faded case colors. Wood is sound with minor nicks & scratches and retains most of a wonderful hand worn patina with about 75% orig finish showing through. Mechanics are fine, bright shiny bore with a few spots of minor pitting 4-33302 JS460 (3,000-5,000)

FINE EARLY SPENCER CIVIL WAR RIFLE SN 9691. Cal. 56-56. Standard Spencer rifle with 30” rnd bbl, square base front sight/bayonet lug with German silver blade and Spencer ladder rear sight with tension spring. Mounted with straight grain, uncheckered American walnut with full length forearm & straight stock with standard Spencer buttplate & sling swivels. Left side of wrist has the two correct cartouches. Quite a number of these Spencer rifles were issued to regiments of Ohio sharpshooters who used them very effectively throughout the war. There are recorded instances where the presence of these rapid fire rifles turned the tide of a particular battle. It is also recorded in National Archives that the soldiers issued these rifles were allowed to keep them after the war along with accouterments for $10.00. Consignor states this fine Spencer is the best conditioned 1860 Spencer to come to auction since the Tom Lewis collection. Consignor states that this is the best conditioned 1860 Spencer rifle to come to auction since the Tom Lewis collection. CONDITION: Fine. Bbl retains 95-97% strong orig blue with only slight muzzle edge wear. There is some fine pitting on sight tension spring. Receiver & lockplate retain 60-70% faded orig case colors with moderate pitting. Wood has usual nicks, dings & scratches with a couple of shallow gouges and overall is a dark oiled patina. Mechanics are fine, very bright shiny bore. 4-32816(12,000-15,000)

SCARCE BELGIAN MADE SPENCER CARBINE. SN 1760. Cal. 50 RF. Made in 1873 under license from Spencer by Falisse & Trappman in Liege, probably less than 1,000 produced according to the book Spencer Repeating Firearms, Marcot on pp. 157-58. Externally has all the appearance of a standard Spencer carbine with 20″ rnd bbl, square base front sight and standard Spencer rear sight. Top of receiver is marked “UNION ARMORIERE BELGE / -LIEGE-“. It has various Belgian proof marks on bbl, receiver & wood with a large cartouche on right side of buttstock dated “1873”. It has a sling bar & ring on left side of wrist and a sling loop on bottom of stock. PROVENANCE: Glenn Marsh Collection. CONDITION: Very good. Bbl retains about 80% dark orig blue with balance a mottled blue/brown patina. Receiver is mostly a brown patina with some silvered case colors. Wood is sound with numerous dents, dings & scratches and retains a dark oil finish on forearm and 75-80% orig varnish on buttstock. Mechanics are fine, brilliant shiny bore. 4-59536 JR58 (2,000-3,000)

1859 SHARPS MITCHELL NAVY CONTRACT PERCUSSION 3-BAND RIFLE. SN 42267. Cal. 52. Standard 3-band rifle with 30” rnd bbl, rectangular base front sight with German silver blade & a saber bayonet mount under bottom of muzzle. It has Lawrence Patent ladder rear sight & usual markings on bbl, receiver & lockplate. Mounted with straight grain uncheckered American walnut with full length forearm & straight stock with usual Sharps buttplate. It has a 2-pc patchbox in right side of butt & sling swivels. This is from the Navy Contract. CONDITION: Very good. Traces of orig finish remain on bbl in most sheltered areas with metal being a very dark smooth even brown patina. Receiver & lockplate retain about 30% dark case colors with balance of metal a dark brown patina. Stock has a few chips back of lockplate and shows moderate to heavy wear. Mechanics are fine, strong bore with moderate pitting. 4-32815(6,000-7,000)

CIVIL WAR ERA MODEL 1865 SPENCER CARBINE SN 15224. Cal. 56-56. Standard Spencer carbine made under the Burnside Contract and so marked on top of receiver. Made without Stabler cutoff. It has 20” rnd bbl, square base front sight with Spencer ladder rear sight with tension spring. Mounted with nicely figured, uncheckered American walnut with std fnd forearm & straight stock with regular Spencer buttplate. It has a sling bar & ring on left side of wrist and there are three cartouches also on left side of wrist, one is partially covering another. A large number of these Civil War carbines were re-issued to cavalry units on frontier and were in service throughout Indian Wars. CONDITION: Very good to fine. Bbl & band are a smooth, even, plum-brown patina with strong blue around front sight. Receiver, lockplate & hammer are mostly a silver/gray patina from faded case colors. Stock has a number of small chips around receiver with grain checks back of sling bar and at buttplate on left side with another tiny hairline back of lockplate and a couple of chips and overall retains a fine hand worn patina with about 50% orig finish showing through. Left side of wrist has a dark worn spot from a carbine sling snap indicating this carbine saw considerable cavalry service, probably on frontier. Mechanics are fine, strong bright bore with scattered light to moderate pitting. 4-32603 JR511 (2,000-3,000)

RARE 2ND MODEL BURNSIDE SADDLE RING CARBINE SN 905. Cal. 54. Only about 2,000 of these carbines were manufactured in the period 1860-62 on government contracts and all were issued to active cavalry and infantry units with most seeing continuous service throughout the Civil War. It is known that this model was issued to the 1st Rhode Island Infantry who were in the opening attack at 1st Bull Run in July, 1861, Flayderman’s Guide to Antique American Firearms. This carbine has 21” rnd bbl without forearm and has a pinched blade front sight with two position flip rear sight graduated to 500 yard. Top of bbl is marked “CAST STEEL 1861”. Receiver has a very light strike of the Burnside’s patent mark on the top and has the Burnside Rifle Co. lockplate marking. There are small inspector initials on various parts. Mounted with straight grain, uncheckered American walnut stock with carbine buttplate and a sling swivel on bottom. It is has a sling bar and ring on left side of receiver. CONDITION: Good to very good, all matching. No original finish remains with bbl being a smooth, dark brown patina with some moderate rust on bottom side. Receiver, lockplate, hammer and lever are a medium brown patina with fine pitting. Stock is sound with cartouche worn away and retains a dark brown, hand worn finish with light to moderate nicks, dings and scratches. Hammer is not solid in safety notch, otherwise mechanics are fine, strong dark bore with heavy pitting. 4-32812 JR522 (3,000-5,000)

SHARPS NEW MODEL 63 PERCUSSION CARBINE. SN C47895. Cal. 52. Late production standard carbine with 22″ rnd bbl, square base German silver front sight and Lawrence patent ladder rear sight. Receiver and lockplate have standard marking, and it has a sling bar and ring in left side. Mounted with very nicely figured, uncheckered American walnut with standard rnd forearm and straight stock with carbine buttplate. Tiny inspector initials “T. W. R” on comb just in front of buttplate tang. Appears to be an arsenal rebuild. CONDITION: Exceptionally fine. Retains virtually all of its arsenal finish to both metal and wood with strong bright blue on bbl, brilliant case colors on receiver, hammer, and lockplate with strong dark colors on lever and bbl band. Buttplate retains most of its arsenal case colors, turning dark. Wood is sound with only a very few, very minor handling and storage marks and retains virtually all of its beautiful oil finish. Mechanics are crisp. Brilliant, shiny bore. 4-31540 JR160 (3,500-5,000)

SHARPS NEW MODEL 63 CONVERSION CARBINE SN C15074. Cal. 50-70. Standard conversion carbine with 22” rnd bbl, square base front sight with German silver blade & Lawrence Patent ladder rear sight. It has standard markings on bbl, receiver & lockplate. Mounted with nicely figured, factory replacement, straight grain American walnut with std carbine forearm & straight stock with regular Sharps buttplate. It has a cartouche in a ribbon left side of buttstock. It has a sling bar & ring on left side of wrist and has orig 6-groove rifled bbl. CONDITION: Very fine. Bbl retains about 95% strong orig blue with slight muzzle wear. Receiver, lockplate & hammer retain most of their orig case colors, somewhat faded but strong & bright in sheltered areas. Wood is sound with feathered look and a few minor nicks & scratches and retains most of its orig oil finish. Buttplate retains most of its strong case colors. Mechanics are crisp, strong bright bore with scattered light to moderate pitting. 4-32776 JR512 (3,000-4,500)

SHARPS NEW MODEL 1863 CONVERSION CARBINE SN C10223. Cal. 50-70. Standard conversion carbine with 22” rnd bbl, square base front sight with German silver blade & Lawrence Patent ladder rear sight. It has standard markings on bbl, receiver & lockplate. Mounted with nicely figured, factory replacement, straight grain American walnut with std carbine forearm & straight stock with regular Sharps buttplate. It has a cartouche in a ribbon left side of buttstock. It has a sling bar & ring on left side of wrist and has orig 6-groove rifled bbl. CONDITION: Fine to very fine. Bbl retains 65-75% thin orig blue mixed with light patina with strong blue in sheltered areas. Receiver, lockplate & hammer retain bright case colors in very sheltered areas with balance turned silver and a few scattered small spots of surface rust. Wood is sound with forearm showing a fine hand worn patina with a few minor scratches. Buttstock has a chip back of lockplate and a few handling & use marks and retains a fine hand worn patina with some linseed oil having been wiped on surface. Mechanics are crisp, bright shiny bore with a few scattered spots of light pitting. 4-32775 JR514 (3,000-4,500)

SHARPS NEW MODEL 1863 CONVERSION CARBINE SN C22273. Cal. 50-70. Standard conversion carbine with 22” rnd bbl, square base front sight with German silver blade & Lawrence Patent ladder rear sight. It has light standard markings on bbl, receiver & lockplate. Bore has orig 6-groove rifling. It has factory replacement, nicely figured, uncheckered American walnut with std forearm & replacement buttstock with cartouche in a small ribbon on left side. It has a sling bar & ring on left side of wrist. CONDITION: Fine. Bbl retains blue in very sheltered areas and around front sight, being mostly a dark plum-blue patina with light, fine surface rust. Receiver & lockplate retain 50-60% faded case colors with balance a brownish patina. Wood is sound with minor chips behind sling bar and usual nicks, dings & scratches and retains a hand worn patina that will clean much better. Mechanics are crisp, bright shiny bore with scattered fine pitting. 4-32604 JR510 (2,000-3,000)

SHARPS & HANKINS 1862 CARBINE. SN 4156. Cal. 52 RF. Navy type carbine with 24″ bbl covered in leather with stamped anchor clearly visible on top. Pedestal mounted blade front sight and 800 yard graduated rear sight. Second model frame with floating firing pin mounted on the recoil shield is stamped “SHARPS & HANKINS, PHILADA” on the right side, and “SHARPS PATENT 1859” on the left side along with the 1865 Naval reinspection stamp “H.K.H”. Mounted in a straight hand walnut stock with brass buttplate and inletted sling swivel stud with ring. A small inspector’s “M” is stamped in the bottom of the stock between the trigger tang and swivel stud. CONDITION: Fine to very fine. Leather bbl covering is intact with some minor separation of the seam and degradation where covering meets the action. Otherwise leather is sound and retains most of its hard black finish with some cracking and chipping over its length. Trigger guard metal appears to have been professionally restored many years ago. Receiver retains generous portions of orig blue finish. Wood is cracked behind the top tang on the right side and retains most of its old restored finish with scattered light handling marks. Brass buttplate has taken on a medium mustard patina. Mechanically fine. Very good bore with sharp rifling . 4-32810 WD57 (1,500-2,500)

FINE TRIPLETT & SCOTT CIVIL WAR CARBINE SN 4956. Cal. 50 RF. Scarce Civil War era carbine with 22” rnd bbl, pinch blade front sight and small ladder rear sight. Mounted with straight grain, uncheckered American walnut with rnd forearm & sgl band with straight stock & carbine/musket buttplate. There are tiny “NWB” inspector initials on left side of butt at buttplate. It has unusual sling loops at heel & toe. This is a repeating rifle with magazine tube set at an angle into buttstock. It functions by means of depressing a lever on top left side of frame & rotating bbl to right which activates extractor for unloading. Rotating bbl through about 200 degrees pushes spring loaded magazine cover aside allowing a fresh cartridge to be loaded into chamber. Left side of breech block is marked “KENTUCKY”. There were 2,000 of these short bbl carbines ordered by the State of Kentucky for their home guard to protect supply lines during Sherman’s Atlanta Campaign. They were received too late to see service in the Civil War. CONDITION: Very fine to extremely fine. Bbl retains 93-95% strong orig blue with a small scrape, a few light scratches and a couple of spots of surface rust. Breech block retains about 95% strong orig blue. Receiver, top & bottom tangs, retain most of their orig faded case colors, stronger in sheltered areas. Stock has a couple of cracks on right side of wrist & another back of top tang, otherwise wood is sound with its orig raised grain feathery look & a dark orig oil finish. Mechanics are fine, brilliant shiny bore. 4-32921 JR515 (3,500-5,500)

TRIPLETT & SCOTT REPEATING CARBINE. SN 1483. Cal. 50 RF. Rare Civil War era repeating carbine with 30” rnd bbl, pinched blade front sight & small carbine ladder rear sight. Left side of breech block is marked “KENTUCKY”. It has usual company markings on receiver & top tang. Magazine tube is located on left lower side of receiver and extends down into buttstock. Loading & ejecting is effected by depressing the lock lever on left side of hammer and rotating bbl & breech block to the right about 200 degrees, which activates extractor and continued rotation to the stop moves the spring-loaded magazine tube cover aside along a cartridge to be automatically loaded into chamber. In addition this unusual carbine has two sling swivels at heel & toe of stock. Mounted with nicely figured, uncheckered American walnut with tiny rnd forearm & straight stock with carbine buttplate. About 3,000 of these carbines with this bbl length were purchased by the State of Kentucky to arm the Kentucky Home Guard to protect supply lines for Sherman during his Atlanta campaign. They arrived too late to see Civil War service. CONDITION: Very fine. Bbl & breechblock retain 93-95% strong orig blue and receiver most of its orig case hardening turned silver with strong case colors on left side with faded colors elsewhere. Stock has repaired cracks over the thin part of magazine area and overall retains a fine professionally restored finish. Mechanics are fine, bright shiny bore with scattered pitting. 4-32814 JR452 (2,500-4,000)

RARE MUSKET AND BAYONET CARRIED BY PRIVATE JOSEPH PEAKER OF COMPANY A, 24TH REGT., U.S. COLORED TROOPS. . Rarely offered are weapons used by black troops during the Civil War. Accompanying this 1863 dated, Model 1861, Bridesburg contract musket is a letter from the consignor, who states his descendant was a doctor working in New Hope, PA, and he was given this musket and enlistment paper of Pvt. Peaker by a patient. Enlistment paper, 10” x 6”, though in poor condition, is easily discernible. It was written from Camp William Penn at Chelton Hills, PA., March 27, 1865. This is the only enlistment paper of this style for a black trooper we have ever seen. The enlistment document, partly printed, partly hand written has a standing Union soldier in the lower left hand corner surmounted by an American eagle and shield above. The document has a fancy floral border. The hand written sections name Joseph Peaker from the State of New Jersey as appointed into the 24th Regiment U.S. colored Troops as of January 20th 1865. The accompanying musket has rack numbers “24 / 84” stamped on buttplate, which probably denote a gun (#84) in the 24th Regt. This regiment was principally recruited in the eastern section of Pennsylvania, and was organized at Camp William Penn, on the 17th of February, 1865, with the following field officers: Orlando Brown, Colonel, James M. Trippe, Lieutenant Colonel, Robert E. Stewart, Major. A large proportion of the commissioned officers had previously been in the service. Early in May, the regiment proceeded to Washington,D.C. and was stationed in Camp Casey, on the Virginia side of the Potomac, opposite the city. On the 1st of June,the regiment was sent to Point Lookout, Maryland, where it was employed in guarding rebel prisoners. About the middle of July, it was ordered to Richmond, Virginia, and after a delay of two weeks, was assigned to duty in the sub-district of the Roanoke, comprising six counties, with headquarters at Burkesville. Posts were established at each county-seat, where government supplies were distributed to the needy inhabitants, and the troops, were employed on picket and provost duty to preserving order in this section of Southwest Virginia. The regiment continued in this duty until near the close of September, when it was ordered to Richmond, and on the 1st of October, 1865 was mustered out of service. A very rare opportunity to acquire an identified weapon from this historic colored unit. CONDITION: Paper is cracked and separated at numerous folds, with minor paper losses and dry mounted on board. Metal surfaces of musket are cleaned and are gray and pitted. Gun is missing rear sight. Stock is sanded and varnished. Accompanying bayonet is also cleaned, gray, and pitted. 4-32914(3,000-10,000)

COLT MODEL 1861 SPECIAL MUSKET. SN NSN. Cal. 58. Rare Colt “Special Musket” with 39-1/2″ rnd bbl, square base front sight/bayonet lug with 3-leaf musket rear sight and three bands with sling swivels. It has a 2-pc trigger guard & a tulip head ramrod. It has usual inspector marks & lockplate markings with date “1864” on top of bbl flat and lockplate. Left side flat has two crisp cartouches with small inspector initials on & below trigger guard and on comb of stock, in front of buttplate tang and on other parts. Quite a number of these well made rifle/muskets were produced at Colt with many of them going to state militias accounting for their high percentage of high condition pieces still found today. CONDITION: Very fine to extremely fine. Bbl retains generous amounts of its orig polish with top area being mostly a medium gray patina. Lockplate & hammer, likewise, have turned a shiny gray patina with generous amounts of orig bright finish remaining. Stock is completely sound with the feathery look and retains most of its fine factory oil finish with a couple of light scratches. Mechanics are crisp, brilliant shiny bore, probably unfired. 4-32819 JR446 (3,500-5,000)

SCARCE WATERTOWN MODEL 1861 CONTRACT RIFLED MUSKET. SN NSN. Cal. 58. Standard 61 musket with 39-1/2” rnd bbl, square base front sight/bayonet lug with 2-leaf musket rear sight. It has three bands with spring keepers and a tulip head ramrod with sling swivels. Lockplate has an eagle in front of hammer and “U.S. / WATERTOWN” with date “1864” behind hammer. Same date is on top flat of bbl by nipple with “V P” and eagle proofs on top left flat. Left side panel of 1-pc walnut stock has two legible cartouches. Charles B. Hoard of Watertown, NY, supplied 12,800 of these arms in period 1863-65. CONDITION: Very fine. Metal has a cleaned orig type finish with some mottled surface etching on lockplate & fine pitting on hammer. Trigger guard & buttplate also have some very fine pitting. There is a scratch down left side of buttstock with other light storage & handling marks with a few dings on bottom and overall retains a fine hand worn patina with orig finish showing through. Mechanics are fine. 4-32821 JR450 (3,000-4,000)

SAVAGE MODEL 1861 NEW JERSEY RIFLED MUSKET SN NSN. Cal. 58. Usual configuration with 40” rnd bbl, sq base front sight/bayonet lug with standard three blade musket sight, graduated to 500 yards. Lockplate has usual Savage markings and is dated “1863”. Same date and “VP” & eagle proofs are on the breech end of the bbl. Left side flat of bbl and left side flat of stock are stamped “N.J”. Several thousands of these rifled muskets were manufactured in the period 1862-64 and were primarily issued to New Jersey Units, although a few were sold to other states to arm their units. CONDITION: Fine. Metal, overall retains a cleaned gray patina beginning to re-patinate with scattered fine pitting. Stock has a crack in front of lockplate, otherwise wood is sound with minor nicks and scratches and retains most of an old, cleaned, hand worn patina. Mechanics are crisp, very bright shiny bore. 4-32820 JR528 (2,000-3,500)

RARE SPRINGFIELD MODEL 1841 CADET RIFLE SN NSN. Cal. 57. Rare cadet rifle, rifle of Civil War Generals. Virtually every Union and many Confederate Generals trained at West Point using this rifle. It has a 40” rnd bbl with three bands having the split front band with integral front sight. It has a small size lockplate with a small eagle over “US” in front of the hammer and “SPRING / FIELD / 1844” vertically behind the hammer. It has a J-shaped iron side plate with two pc trigger guard and musket buttplate with no provision for sling swivels. It is mounted in a one pc, full length, uncheckered American walnut stock. According to Flayderman’s Guide to Antique American Firearms only 450 of these were produced and was specifically designed for use of the Corps of Cadets at West Point and was in use until 1856. PROVENANCE: U.S. Military Academy at West Point CONDITION: Good. No original finish remains with the metal being a dark brown even patina with moderate to heavy pitting around the nipple area. Stock has a chip at the toe and hairline below bottom tang on trigger guard and has normal light nicks, dings and scratches and retains a dark, hand worn patina. Mechanics are fine, bore is worn and dark. 4-32715 JR524 (5,000-7,000)

FINE WHITNEY MODEL 1841 MISSISSIPPI RIFLE SN NSN. Cal. 54. One of the more beautiful rifle muskets made, these fine rifles have 33” rnd bbl, tiny brass front sight with no provision for a bayonet. It has fixed rear sight and is mounted in 1-pc uncheckered American walnut stock with brass furniture and a brass tipped ramrod. Lockplate has usual markings with date “1851” which date is also on top tang. Left side panel of stock has two legible cartouches. Right side of butt has a large 2-pc brass patchbox that contains a spare nipple & musket tool. They were produced in period 1843-1855 in fairly large quantities and saw use throughout Civil War. CONDITION: Very good. Bbl retains a mottled silver/brown patina with scattered fine pitting. Lockplate & hammer retain traces of orig case colors being mostly a mottled silver/brown patina. Stock has a couple of small chips in front of lockplate and back of top tang, otherwise wood is sound with nicks, dings & scratches and retains a fine hand worn patina. Mechanics are fine, strong bright bore with pitting in grooves, may clean a lot better. 4-59698 JR535 (2,000-3,000)

FINE REMINGTON ZOUAVE RIFLE MUSKET SN NSN. Cal. 58. One of the most beautiful long arms of the Civil War. The Zouave has a 33” rnd bbl with dovetailed, half round front sight base with blade and a three position musket rear sight graduated to 500 yards. Lockplate has the usual Remington markings and is dated “1863”, which date also appears on top of bbl along with the “VP” and eagle proofs. It has “STEEL” on the left side flat with inspector initials. It is mounted in nicely figured, uncheckered, straight grain American walnut full stock with brass furniture having two bbl bands with sling swivels on top band and trigger guard. Left side flat has two crisp cartouches and two small holes where probably someone had hung it on a wall or in a display as there is a corresponding hole on the left side of forestock below the top band. There is a two pc brass patchbox on the right side of the butt which contains a spare nipple. PROVENANCE: Glenn Marsh Collection CONDITION: Very fine to extremely fine. Bbl retains most of its strong, original blue with a few light pinpoints of fine rust. Lockplate and hammer retain dark case colors. Stock has a crack through the aforementioned hole in the forestock, otherwise the wood is sound with minor handling and storage marks and retains about all of its strong, original finish. Brass has a medium mustard patina. Mechanics are crisp, bright shiny bore. 4-59697 JR531 (4,000-6,000)

IDENTIFIED CIVIL WAR ENFIELD RIFLED MUSKET. Cal. 58. NSN. Short rifled musket with 32-1/2” rnd bbl, saber bayonet mount on right side at muzzle with two bands & brass forend cap with slotted head ramrod. It has a square base front sight bayonet lug stamped “520” with 1,000 yd ladder rear sight marked “C” on left side with “1861” dated lockplate. Mounted in a 1-pc walnut stock with brass trigger guard & buttplate. Top flat of bbl by nipple is hand stamped in tiny letters “SERGT. JERRY FISHER / CO. D. 147. P.V.V.” Accompanied by a German made orig saber bayonet stamped on the butt “52x” (the last digit being indiscernible) with a knight’s head on left ricasso with a 22-3/8” Yaghatan blade with unstopped fuller, iron crossguard with muzzle ring and checkered black composition scales with eagle head pommel without scabbard. Jeremiah Fisher enrolled in the 147th Regt PA Vol. Inf. on 13 Aug, 1861 and was discharged at the end of the war on 15 July 1865. During those four years he attained the rank of Sergeant. His unit participated in many of the major battles of Civil War including Cedar Mtn., 2nd Bull Run, Antietam, Harper’s Ferry, Leesburg, Winchester Chancellorsville (where the unit was decimated losing about 1/3 of its number in battle). They fought at Gettysburg on 1 July to the right of Round Top and the next two days at Culp’s Hill. From there they fought at Lookout Mtn. and Ringgold and afterward moved with Sherman in the Atlanta campaign and again fought at Resaca, New Hope Church, Kennesaw Mtn. & Peachtree Creek. They continued with Sherman to the sea and then turned north through the Carolinas marching all the way to Washington where they were mustered out July 15, 1865. Sgt. Fisher was born March 1, 1843 and died Oct. 11, 1931. Accompanied by a large packet of Sgt. Fisher’s unit muster rolls and pension application & misc. correspondence. CONDITION: Good. No orig finish remains being a cleaned patina overall with moderate to heavy pitting over bbl & bands with light pitting on lockplate & hammer. Stock has a crack in front & back of lockplate and another on left side panel with a plugged hole in bottom of stock and some filled areas with several light nicks & dings and retains an old oil applied finish. Mechanics are fine. Bayonet has a dark patina with fine pitting. Handle shows heavy wear. 4-32818 JR448 (6,000-10,000)

MODEL 1816 CONTRACT M.T. WICKHAM CONVERSION MUSKET SN NSN. Cal. 69. Wickham musket with 42” smoothbore bbl with Hewes & Phillips conversion with a breech plug and bolster with cleanout screw and a new hammer. Lockplate has usual late style markings with date “1830” vertically behind hammer. It has the “H&P” stamp on new breech plug with date “1861” on tang. Bbl has a square bayonet lug on top of muzzle with three bands, front being split with a replaced integral front sight. It has a 3-blade musket sight graduated to 500 yards mounted backwards and its orig buttonhead ramrod. It has 2-pc trigger guard & sling swivels. Left flat of stock has outline of two cartouches and left flat of bbl is stamped “NJ” for New Jersey. Bottom of stock, back of bottom tang, is stamped “47” upside down. About 8,000 of these conversions were made in period 1861-62, mostly for the State of New Jersey. Accompanied by a triangular socket bayonet marked “US” and “EB”. CONDITION: Fine. Metal retains a mottled mixed silver & brown patina with silver being orig bright polish. Stock is sound with light handling & use marks and retains most of its orig oil finish. Mechanics are fine, strong bore with moderate to heavy pitting. Bayonet is also a mottled silver/brown patina with a few nicks & dings on edges and is slightly sprung in shank. 4-59748 JR533 (2,000-3,000)

H & P CONVERTED POMEROY MODEL 1816 MUSKET SN NSN. Cal. 69. Beautiful 2nd type conversion by Hewes & Philips of Newark, NJ with large percussion bolster installed, without cleanout screw and marked on outside “H & P”. Lockplate has the Pomeroy and eagle markings in front of hammer with “US” and “1830” vertically behind hammer. The date “1862” is by conversion bolster. It has 42” smooth bore bbl with bayonet lug on top of muzzle and three position rear musket sight with middle blade broken. It is mounted in a nicely figured, tiger striped, uncheckered American walnut full stock with three bbl bands, with front being split and having an integral front sight. It has a button head ramrod with J-shaped side plate and two pc trigger guard with sling swivel and musket buttplate. Left side flat is stamped in small letters “AR / V”. Approx. 12,000 of these muskets were so altered under U.S. contract and presumably issued to militia as well as combat units. According to Flayderman’s Guide to Antique American Firearms these altered muskets had rifled bores. CONDITION: Extremely fine. Metal retains a wonderful, cleaned to original bright metal finish with a few small nicks and scratches and minor scattered spots of pitting. Stock is sound with minor nicks and dings and retains its wonderful, original oil finish. Mechanics are crisp, strong bore with light pitting. 4-32822 JR529 (2,500-4,000)

CIVIL WAR FORAGE CAP IN SUPERB CONDITION. This is a classic, tall brimmed forage cap, often seen in photography of Civil War soldiers, and often referred to as a bummer’s cap. This kepi is in fine condition. Body shows little or no damage and no discernible moth damage at all. Stitching is tight, internally and externally. Black cotton liner is intact with maybe a few loose stitches. Patent leather sweatband is 1-3/8” tall with sewn inner edge. Old, folded newspaper is used as backing behind sweatband. Chin strap is attached with eagle “I” buttons. Leather brim shows little wear with only minor crazing to black surface. You are bidding on as fine a condition Union forage cap that can be found. CONDITION: Fine overall as described above. 4-31582 JS275 (6,000-8,000)

Revised: 10/19/2007

(Correction) Please see the attached photograph, which is an appropriate representation of this rare and outstanding Civil War hat. The current image in the printed catalog is not appropriate.

SUPERB CIVIL WAR OFFICER’S SLOUCH HAT. This wonderful slouch hat is complete with Officer’s hat cord, cockade, and feather, and an added false-embroidered horn insignia with false-embroidered “16” inside loop. Silk lining inside hat has a fine maker’s label “J. C. Jones / Dealer in military equipments / Fortress Monroe”. This hat was part of a large group of identified Mass. Civil War coats and equipage found last year at a Boston, Mass. Estate. Sweatband in hat is tarred linen and is 3” tall. This is as fine a Union slouch hat as you will find. These hats are so rare and so seldom are offered, especially in this condition, with such a great maker’s label. CONDITION: Hat is very good overall with ½” sewn border in very good condition. Silk liner is intact but loose. Tarred linen sweatband is about 1/3 missing. 4-31581 JS274 (17,500-27,500)

FROCK COAT AND SWORD GROUPING OF CIVIL WAR LIEUTENANT C. H. RAYMOND, 121ST PENNSYLVANIA INFANTRY. This important grouping of Lt. Raymond’s uniform pieces and weapons includes his officer’s frock coat, foot officer’s sword, belt and buckle, insignia items, photos, officer’s waist sash, small side Bowie knife, shawl/blanket, GAR hat, and other assorted items. Charles H. Raymond was commissioned 2nd Lt of Co F, 121st Pa Infantry, upon the unit’s formation in Philadelphia in Sept 1862. The 121st Infantry had a long and important history of war service, fighting in several significant actions including Sharpsburg, Chancellorsville, Gettysburg, the Wilderness, Spotsylvania, through to the surrender at Appomattox Court House. Lieut. Raymond was shown as discharged for some unknown reason on July 23, 1863, just 20 days following the unit’s engagement at Gettysburg. Raymond’s very fine officer’s frock coat has all its correct Infantry “I” buttons. Coat is fully lined, as is typical. Orig shoulder straps have been previously removed and are included. Location of the straps, along with remaining attachment threads, can be seen. Also included is a complete and nice Model 1850 foot officer’s sword with nice leather scabbard that has no breaks or flaking. Blade is marked near the hilt “Mintzer / Philada.”. There is also the typical floral engraved blade with “US”. There is also some age spotting, but overall it is in very good condition. Raymond hand-scratched his initials “C. H. R.” into the brass guard. The sharkskin grip is present, but only a few wraps of wire remain. The remains of his broken officer’s waist belt with buckle are present, as is the red officer’s waist sash, which is in excellent condition. The grouping includes two original CDVs of Lt. Raymond. Both views are full length and in uniform. The first shows him with frock coat and hat, inked on the bottom “C. H. Raymond”. The second is back-marked “Brady, . . . New York.” and shows him with coat, hat, sword belt, and sword. His name, rank, unit, and company Captain’s name are inked on the rear. Included is a neat small side Bowie knife (overall length: 10-1/2”) with scabbard marked “I*XL”. Blade has rusted and shows light pitting, being marked “Wostenholm & Son / Washington Works / Sheffield”. Inset into the knife’s stag antler handle is a small silver oval plaque that is engraved “C. H. R. Pa.”. There are two war-dated letters by Raymond to his father. The first is dated Jan 13, 1862, and the second Feb 3, 1862. There are several small old period ink labels with Raymond’s name, unit, and small descriptions of some items. Raymond’s infantry hat front insignia shows holes where the unit’s numbers were once present. Also included are a single 2nd Lieut. shoulder strap and a matched set of 2nd Lieut. shoulder straps that appear to be trimmed with pewter metal edging similar to Smith Patent sets. Included with the grouping is a damaged tin canteen, 6-1/2” in diameter, that has been painted gold. The style is very similar to styles used by Confederate soldiers during the war and may be a battlefield pickup by Raymond, later painted for display in a GAR Hall or such. See the book Civil War Canteens by Sylvia and O’Donnell (pp. 74-84) for similar examples of Confederate tin canteens. There is also a postwar GAR kepi and set of white gloves. The kepi has a front insignia marked “GAR / 168” for the post number. CONDITION: Frock coat is very good overall with minor staining. Some thread remains where straps have been removed. Sword is missing most of its wire wrap. Sharkskin is intact. Hilt and scabbard mounts have been cleaned. Gray/bright blade exhibits much of its orig frosting with some black staining and pitting. Scabbard has shrunk approx. ½” but leather body is intact with scattered mottling and crazing. Bowie knife blade is cleaned, sharpened, and pitted, though German silver mounts on scabbard and knife are very good. Leather covering to wood scabbard body mostly intact with good “I*XL” mark. Sash is very good and complete, though color has faded to a purple, with scattered staining. Shawl/blanket is very good overall, with some staining and fraying at edges. Sword belt, as described above, is broken into several pieces, and some parts are missing. Buckle, photographs, and insignia are all very good overall. Confederate tin canteen is heavily dented and missing spout with much chipping to old gold paint. GAR kepi and gloves are very good overall. 4-32923 JS255 (6,500-8,500)

NINE-BUTTON REGULATION FROCK COAT GROUPING OF CIVIL WAR SERGEANT ALBERT FOSS, TWICE WIA, 7TH NEW HAMPSHIRE INFANTRY. This grouping is centered on the extremely rare regulation enlisted soldier’s Sergeant Infantry 9-button frock coat and the soldier’s associated papers, war letters, and great photo. Albert H. Foss was mustered into service as a Pvt in Company A, 7th NH Infantry, in Oct 1861 and served with the until discharged in Dec 1864. He was promoted to both Cpl and Sgt, with his orig promotion paperwork accompanying the lot. Foss was listed as being wounded twice in action, first at Fort Wagner on July 18, 1863, and then at Deep Bottom Run, VA, on Aug 16, 1864. The 7th NH Infantry’s claim to fame was that they led the second wave assault on Fort Wagner on Morris Island, NC. During this engagement, the unit suffered losses of eleven officers killed in action, the highest number of Union officers killed in any single engagement of the Civil War. The regiment’s Colonel Haldinand Putnam was killed in this action. It was during this battle that Sgt. Foss was first wounded. Foss’ regulation enlisted 9-button has the correct orig period Sergeant’s stripes on each sleeve. Correct eagle infantry “I” buttons are present, with one replacement button and one missing button. Coat has no visible maker’s marks, but does have the correct partial lining on the coat’s body front and sleeve linings. Foss appears to have slightly altered the coat’s collar, by lowering the height. This was a common alteration. There are some very minor mothing and small holes present, but the coat has the appeal and wear consistent with a war-used uniform. There is a very nice 1/6 plate ambro-type photo in a case of Pvt Foss dating to the start of his service. This view shows Foss in full enlisted 9-button frock coat, with waist belt and cross belt, Enfield musket at his side, and wearing a nice Hardee hat with Company “A” and regimental “7” on front. This group also includes an important set of eight letters written home to his brother Silvester Foss, Strafford Corners, NH. Most of the letters are included with their addressed envelopes, which have had the stamps clipped out. These letters are addressed and dated as follows: 1) Beaufort, SC, July 28, 1862; 2) St. Augustine, Fla., Nov. 7, 1862; 3) St. Augustine, Fla., Jan. 6, 1863; 4) St. Augustine, Fla., Feb. 1, 1863; 5) St. Augustine, Fla., Feb. 13, 1863; 6) St. Augustine, Fla., March 27, 1863; 7) Folly Island, Charlestown Harbor, SC, June 28, 1863; 8) Bermuda Hundred, VA, July 29, 1864. Several important war period documents related to Foss are with the group, including the orig copy of his discharge “Sergt. Albert H. Foss,” dated 27th Dec 1864 and signed by Col Putnam (who was later killed leading the regiment in the charge at the assault on Fort Wagner), and Foss’ appointment certificate to Sgt in the 7th given at Bermuda Hundred, VA, dated 6 August 1864 and signed by Colonel Abbot of the 7th NH Vols. These two grade appointment papers are sized at 10” x 14”. There is also a nice albumen photo of Veteran Foss with a few of his old mates. Titled “1861-1865 Only a few of Us Left – Civil War Veterans – Alton Bay Aug. 1911,” it shows 18 white-haired men posed in front of the sign. Albert Foss is shown seated third from left. CONDITION: Overall very good as described above. 4-32925 JS260 (12,000-15,000)

INFANTRY GREAT COAT AND REGULATION BLANKET OF CIVIL WAR PRIVATE JOHN O. QUIMBY. This is a unique uniform grouping of a Maine Enlisted Infantry soldier who, at a slightly advanced age, served as a regimental drummer. Drummer John O. Quimby was a native of Brunswick, ME, enlisting in the 25th ME Infantry raised in Portland. In state records, Quimby was noted as being a 35 year-old “musician” who served in the unit from September 1862 to July 1863. The 25th ME was a 9-month regiment that was stationed in the Washington, DC area. Union regulations authorized the assigning of two field musicians for each infantry company of a regiment. These were generally a single drummer and fifer. Principal to the grouping are two period CW photos of Quimby with his drum, his Federal government regulation Infantry great coat, and regulation blanket. Quimby marked his ownership and regiment on both the coat and blanket. Musician Quimby’s interesting early war regulation Infantry Great Coat is made of jean cloth wool. Most Civil War regulation coats were constructed of sky blue wool kersey. Early in the war, though, when clothing and equipment were rapidly pressed into service, some unique combinations were witnessed. These regulation characteristics include a stand-up collar, single-breasted front with five buttons, a short cape, and fold back cuffs. A near exact identified example is shown in the book Echoes of Glory, Arms and Equipment of the Union by Time-Life Books (p. 129). This published example is incorrectly labeled as a “state contract” overcoat. The example being sold here confirms that these were manufactured under an early war Federal contract, being marked by a Federal appointed inspector. The overcoat is maker-marked inside the right sleeve with “W. B. Button / NY” and two dots to signify the size. Inside the left sleeve lining is the Federal inspector mark “CN Inspector / CT Hathaway / New York”. Federal clothing records from the U. S. National Archives (copies included) show that manufacturer Button delivered “Foot Great Coats” under several contracts totaling 45,000 from Sept to Oct 1862. Despite this seemingly large number, these early war coats are quite rare. The coat’s red interior lining has been removed, but traces can still be seen. There is some minor damage to the coat, having exposed moth holes. John Quimby stenciled in black ink his name and regiment under the rear of the coat’s cape while also signing his initials and unit inside the left sleeve lining, “JOQ, 25 Me”. Also included with the grouping is Quimby’s Civil War regulation blanket with the proper central stitched “US” marking and end strips. The blanket is the typical aged brown in color and is sized at 70” wide x 77-1/2” long. These blankets are known to be dyed with logwood dyes that fade over time to different colors from the original period of manufacture. The blanket has two 2.5” stripes present on each end. The central “US” markings are approx. 5” tall x 10” across. The stripes and “US” markings are dark blue in color. Underneath the blanket’s “US”, soldier Quimby has again stenciled in black ink his name and regiment onto the blanket. There is a very nice original CDV photo of Quimby with his unique custom tailored musician’s frock coat, hat, and drum. The photo’s back is marked “Hamilton, Court Street, Boston”. It is period pencil marked on the rear with Quimby’s service dates. Also included is an oversized albumen photo in frame (overall size 22” x 25”) of Quimby and other regimental drummers of the 25th ME Infantry, all four being seated in their custom frock coats and drums situated in front. Penciled on the back is “Great Grandfather Quimby in the CW 1862-1863”. This is a great opportunity to purchase a superior condition, early war regulation infantry overcoat and a scarce and beautifully maintained regulation, identified blanket with fine embroidered “US” and bright blue stripes. CONDITION: Blanket is fine overall with good color in blue stripes and blue embroidered “US”. Scattered staining and scattered mothing. Great coat appears sound and in “as found” condition with some newer stitching, tightening up loose seams, and possibly a button or two being resewn. Coat is missing lining in body; however, sleeve linings are intact with maker’s mark, inspector’s and soldier’s ID and unit easily read, as can be seen in photographs, scattered mothing on body of coat. Photographs are both very good overall. 4-32922 JS253 (11,000-14,000)

UNUSUAL “DECORATED” CIVIL WAR TO NATIONAL GUARD PERIOD UNION LINE OFFICER’S UNIFORM FROCK COAT. This dark blue Civil War period Union officer’s frock coat conforms to the U.S. Army pattern regulations for this period. Its materials; buttons and construction all conform to other known frock coats from the period 1860-1865 except for the addition of gilt wire and braid decorations at the collar and on each cuff. The coat is faded therefore it is easy to discern that the braid has been on the coat most of its life if not from the beginning. I can only speculate on these non-regulation additions to this uniform coat. There are three distinct possibilities (a) this coat was custom made and decorated for a Civil War period militia musician, (b) this Civil War period frock coat was later decorated with braid and worn during the veteran period, (c) it dates to the immediate post-Civil War period (perhaps even a recycled Civil War uniform) to the earliest state “National Guard” period (1866-1868). The coat is made of finely woven worsted dark blue wool, three quarter frock coat length with a stand-up collar measuring 2 ½” high and sleeves measuring nearly 9” wide at the elbow. The nine-button front has 8 eagle “I” buttons back marked “*D. Evans & Co.*/Attleboro Mass” (these buttons date from their period 1860-1880, generally considered post-war) which may or may not be orig to the coat. The button back marks do not match those on the cuff and have been added or moved from a former location on the front of the coat. Two cuff buttons are on each sleeve and two remain at the waist in the rear. The interior of the coat is lined in dark green polished cotton with a heavily quilted breast. The skirts are lined with the same material and the sleeves lined in a white osnaburg material. Added or orig to this frock coat is extensive braid decoration on the collar (lined with gold braid containing a looped border) and on each sleeve (trefoils and quatrefoils of narrow braid and wide rope-like braid). A very unusual and interesting coat well worth additional research. CONDITION: Fair. Coat is quite faded with old repairs to the shoulders and some heavy moth holes where the front buttons were once located (this is, generally covered up when the coat is buttoned). Interior is good with some fraying and minor losses to the lining. Some of the braid has come loose. 4-30366 JL14 (1,000-2,000)

Revised: 10/19/2007

(Correction)Man’s name should read James C. Lane.

IDENTIFIED SWORD, CORPS BADGE, PHOTOGRAPH, AND OTHER EFFECTS OF BVT. MAJ. GENERAL JAMES E. LANE, 102ND NEW YORK REGIMENT. You are bidding here on a group of artifacts directly descended in the Lane family. These items consist of 1) Ames 1850 Staff & Field Officers sword, which is uninscribed; 2) a marvelous, inscribed, gold Corps badge, in which the 12th/20th A.C. star is 2-5/8″ across; 3) quarter plate image of Col. Lane on milk glass; 4) post-war business card; 5) wartime note to his wife; 6) contemporary newspaper clipping, dated November 16, 1862; 7) two gold wedding bands (his and his wife’s); 8) gold ring with a cat’s eye; 9) additional watch chain with compass as its fob; 10) a gold owl stick pin; 11) small, enameled GAR medal; and finally, 12) brass compass made in Paris that Gen. Lane used as an engineer after the war. This is a very nice grouping with letter of provenance from family member. The 1850 Staff & Field Officer Sword exhibits a 32″ gray blade etched with various military and floral panels approx. 15″ each. Blade is gray, and etching is mostly discernible and maker marked Amer. Mfg. Co. Chicopee, MA, though gray with black staining and pitting, especially at tip. Hilt is standard 1850 form with “US” surrounded by foliate decoration. Grip is shagreen, covered in twisted wire. Grip has 4″ crack longitudinally running length of grip on reverse. Brass pommel and hilt exhibit traces of orig gilt. Iron scabbard body has 3 brass mounts. Top mount is marked “Ames Mfg. Co. Chicopee Mass.” Mounts are held by screws. Screw to drag is missing. Drag is scuffed and scratched and worn on bottom where it was “dragged”. Decorated mounts exhibit traces of orig gilt. Body of scabbard exhibits several dents and is gray with scattered rust and pitting. Scabbard is missing throat, and sword is missing its protective washer. Images on milk glass are typically painted post-war and were expensive in their day. Coloring on this image, though still vivid, exhibits some paint reductions, especially in the hair. Image shows Lane in his Col. uniform circa 1864. Accompanying corps badge is exquisite. It may, in fact, be the most elaborate and most expensive corps badge ever made. We have never seen anything else like it. It is massive, gold, and jewel-studded, built over a black enameled, beveled star. Star represents the 12th and 20th Army Corps. Jewels are ruby, sapphire, opal, and 5 mine-cut diamonds. There is a small tintype, approx. 1/2″ in diameter, of Gen. Lane wearing his Maj. General’s uniform. 20th A.C. star corps badge is suspended by 4 gold chains by an initialed oval pin with the numbers “102” cut into some hard, white stone. Faces of the star include numerous battles, including Gettysburg, Chancellorsville, Antietam, 2nd Bull Run, Lookout Mountain, Missionary Ridge, Harpers Ferry, Cedar Mountain, Snake Creek Gap, Rocky Face, and the last, chronologically, being Dallas, GA, June 1, 1864. Presentation, finely inscribed on back of badge reads “Presented to / Col. James E. Lane / by the Officers of the 102nd Reg NYV / HE WAS OUR LEADER / in the Battles / inscribed in this Medal / GOD BLESS HIM”. Gen. Lane, after the War, worked as a civil engineer, as his business card states, and must have used the two accompanying compasses in his work. One compass is brass-cased, made by Cruchon & Emons, Paris, SN 1954. The front cover of compass says “US Engineer Corps”. Another small, well-made compass in gold bezel is attached to a gold-filled watch chain. CONDITION: As described above. 4-31530 JS0 (5,000-8,000)

Revised: 10/19/2007

(Correction)Man’s name should read James C. Lane.

VERY IMPORTANT, LARGE, 18-KARAT JOSEPH JOHNSON LIVERPOOL POCKET CHRONOMETER OWNED BY BVT. MAJ. GENERAL JAMES E. LANE. Watch has helical hairspring. SN 43 / 2974. Dial is also marked same. Case is London-made and marked “The Golden Rule” with initials “JEL”. Case letter, old German “L”, dates this watch to 1846. Porcelain dial. Very large and very heavy. Also includes 14-karat chain, and orig rosewood, brass bound box. Movement “fusee”. CONDITION: Very good, running at time of cataloging. 4-31530-1 JS213 (4,000-6,000)

CONFEDERATE TWO-PIECE “CS” BUCKLE ON BELT. This scarce variant “CS” buckle on added belt has welded repair to tongue. Wreath appears untouched, but has a dent at about 10 o’clock, from possibly being shot. There appears to be lead residue in this dent. This may account for the area where buckle has been repaired. This is an interesting relic with a crude repair made to the tongue portion of the buckle that should have had an interesting story. CONDITION: Patent leather belt is sound with new stitching holding tongue in place. Wreath is sound with good patina, though slightly distorted by shot edge. Tongue is crudely welded, as can be seen in photographs and has been cleaned. 4-31119 JS282 (2,000-3,000)

CIVIL WAR ERA BELT. This is a Philadelphia Home Guard oval lead filled buckle on leather belt. CONDITION: Overall buckle is in good condition with belt probably being added and is post-war. 4-31583 JS224 (2,000-3,000)

TWO MASSACHUSETTS OFFICERS BELTS. Two Massachusetts officers belts; one being an 1850 saber belt plate style and the second being an oval 2-pc. CONDITION: Overall good with 2-pc having several cracks in belt. 4-31583-1 BT0 (3,000-5,000)

TWO CIVIL WAR ERA BELTS. This lot consists of a SNY (State of New York) and a musicians buckle. CONDITION: Overall good, though there are several breaks on 2-pc SNY and belt on musician buckle appears to be modern. 4-31583-2 BT0 (500-1,000)

IDENTIFIED CAVALRY BELT AND STENCIL GROUPING OF CIVIL WAR CAPTAIN STEPHEN SWETT, 1ST NEW HAMPSHIRE AND 1ST RHODE ISLAND CAVALRY. This is a nice, identified cavalry officer’s sword waist belt and war stencil used for marking items. Capt. Stephen R. Swett was a NH native who was commissioned as a Capt in the 1st NH Cavalry on Oct. 15, 1861. The 1st NH Cavalry was combined, with staff and enlisted transferred, with the 1st RI Cavalry on Dec 12, 1861. Capt. Swett was promoted to the rank of Mjr on Aug 1, 1862. Belt retains over-the-shoulder strap but lacks the short sword strap. Included is a 3” x 15” brass stencil “Capt. S. R. Swett”, Captain Swett’s officer’s waist sword belt and buckle. There is an oversized card from Swett’s funeral stating “Major Swett died Nov. 23, 1903, 84 years,” as well as a small book for “Major Swett Post No. 32 SUV (Sons of Union Veterans) Oct 1908”. This grouping was previously sold out of the estate of Capt./Maj. Swett. At that time, it included a photo of Capt. Swett and his diary. A copy of the photo is included, but it had previously been sold separately and its location is presently unknown. CONDITION: Belt is solid with crazing to patent leather. Buckle is excellent with probably half its orig gilt. 4-32927 JS265 (1,200-1,500)

CIVIL WAR ERA SURGEON’S KEPI WITH MEDICAL STAFF INSIGNIA. This Chaucer-style kepi is about 2” tall in front with four braids of black cording on sides and forming a quatrefoil on top. Chinstrap is bound by two D. Evans & Co. Staff Officers’ buttons. Attached hat insignia on face of kepi is composed of an embroidered wreath with letters “MS” inset. Leather sweatband inside hat is approx. 1-3/4” tall. Inside top of hat has a padded silk area sewn in concentric circles, which is worn, showing orig newspaper backing used in construction. CONDITION: Exterior body of hat is sound with tearing and breaking to black cording in several spots. Chinstrap is sound, as are brim and sweatband, though sweatband has several tears and is coming loose in areas. Brown cotton lining is intact, but may have had another silk lining covering it which is now only present on top of crown of hat. 4-31112 JS276 (3,000-4,000)

U.S. NAVY TUNIC. Waist length dark blue wool jacket with 3″ wide lapels and dbl breasted front having nine small U.S. Navy convex brass buttons in each row. There are also four buttons on small facing at each cuff. Jacket has two pockets at the waist, one on each side. The body is lined with dark green brocade type material and is lined in the sleeves with muslin. Jacket has a fold over collar approx 3-1/2″ deep. This model jacket was made & used from the Civil War and late into the 19th C. CONDITION: Very good with some scattered but very light moth damage. 4-32700 DM147 (2,500-3,000)

AMERICAN DRAGOON HELMET, 1820 This rare, American Dragoon helmet, made in the style of Tarleton’s Legion helmets of the Rev. War is marker marked by Henry Storms of New York. Label reads “Military Equipments, Henry Storms, Saddler, Caps and Harness Maker, 187 Water Street, New York, Trunks, etc…”. Henry Storms worked at 187 Water Street from 1819-1823. This classic helmet was popular among militias both North and South. They are quite scarce and rarely offered today. This is a fine example that is complete and original with added bear skin comb. The leather cockade has applied 5-pointed. Beveled star. Silk band is held by 2 bullion cords attached to 4 ball buttons. 3” patent leather sweat band in intact and 2 paper labels are mostly complete, pasted in top of helmet. CONDITION: Brass brim to visor is complete but 2” gap is visible at front. Leather body is crazed and flaking. Silk band is faded to a light pink and is frayed in areas. Cockade is missing 1/3 of its points. Sweat band is complete but stitching is loose at the top edge, in places. One label is complete, the other missing about 20%. Bear skin excellent as replaced. 4-31538 JSHW5 (6,000-8,000)

CIVIL WAR REGULATION KEPI RAIN COVER OF LIEUTENANT C. H. RAYMOND, 121ST PENNSYLVANIA INFANTRY. Approximately 15” high, this regulation tarred linen kepi rain cover in excellent condition was part of the 2nd Lieut. Raymond grouping, but is being split out and sold separately due to it being such a unique and rarely offered item. The rain cover is designed to cover the soldier’s kepi hat and neck. It includes two correct 7-1/2” “shoe string” closing ties. A small, attached period pencil note included is marked “This covered cap when it rained – Civil War -.” This is a very rare item that really belongs in any collection of Civil War headgear. Similar examples are shown in the book, Echoes of Glory, Arms and Equipment of the Union by Time-Life Books, p. 189, and also described and shown in the book U.S. Army Headgear: 1812-1872 by Langellier and Loane, p. 110. CONDITION: Very good overall, with minor staining and small debris stuck to tarred surface. 4-32924 JS256 (1,750-2,500)

AUTOGRAPHED CDV OF GENERAL ROBERT E. LEE. Image depicts bearded Lee with uniform; 3 stars on his collar. Signed “R. Lee”. On back of CDV, “Vannerson & Jones, Photographic Artists, #77 Main St, Richmond, VA” also a 2-cent revenue stamp below inscribed “VA, June 20th 1865”. Matted & housed in simple early 20th C. frame. SIZE: 6-1/2″ wide x 8″ high (including frame). CONDITION: Signature faded otherwise good to very good. 8-87555 JJ54 (4,500-6,500)

Revised: 10/19/2007

(Correction)The person depicted on the case is not Zachary Taylor but is Winfield Scott.

RARE MEXICAN WAR VETERAN MEDAL WITH RARE ZACHARY TAYLOR PORTRAIT DAGUERREOTYPE CASE. Papier mache case with front cover featuring bust portrait of Zachary Taylor in full military regalia. Stored within the case is a period & orig, brass, high relief, shield shaped medal depicting eagle, cannons, banners & soldiers in relief above and below “N.Y. Veterans of the Mexican War”. Retains its orig pin on reverse but missing its hasp. SIZE: Dag case: 3-1/2″wide x 4″ high. Medal: approx 2″x2″. CONDITION: Case is good, missing clasp. Medal very good with wear on high points. 8-87553 JJ51 (2,500-3,500)

CIVIL WAR GENERAL’S SWORD SASH. Burgundy sword sash complete with fringe. CONDITION: Some losses to fringe. Some deterioration to fabric. 8-87556 JJ54 (500-800)

WONDERFUL GROUP OF UNION SOLDIER’S LETTERS IN THE 11TH U.S. REGIMENT. Almost all the Civil War letters you see are written by Volunteers because almost all the army was volunteers. Few letters survive from regular army units especially enlisted men’s letters. The writer of most of these letters was obviously well-educated, though he makes spelling and diction errors. His letters are long and detailed with much better than average content detailing death, capture, casualties, camp life, and great insights into the mind of the common soldier. Complete transcriptions of all 28 letters are available. Aldelbert and Augustus Knight’s letters start in July of 1862 and are scattered till the end of the war. Most letters accompanied by corresponding envelopes. Also included in this group is an Andersonville celluloid pin, about 1 ½” in diameter. This pin we have not seen before and must have been worn by survivor or a comrade who died there. Adelbert Knight entered the service March 26, 1862 at Portland, ME as a private in Co. F – 1st. Battalion, 11th Regiment United States Inf. The first battle he engaged in was at Second Bull Run and he participated in the following: Antietam, Fredericksburg, Chancellorsville, Mine Run, Gettysburg, Manassas Gap, Wilderness, Spotsylvania, North Anna and skirmishes too numerous to mention. He was promoted to the Color Guard in April, 1864 and was taken prisoner June 2, 1864 near Mecanicsvi1le, VA and confined in Libby Prison from June 3 to June 8, 1864: Andersonville June 14 to June 28, 1864; Savannah Nov. 22 to 25, 1864; and Camp Florence Nov. 27, 1864 to Feb. 28, 1865. He was paroled at Goldsborough, SC on Feb. 28, 1865 and arrived in our lines the same day and in Wilmington on March 1, 1865 being discharged May 2, 1865 in Camp Parole, the time of service having expired. His intimate comrades in the service were Edmund Ridel; Ira S. Pettit (died at Andersonville), Walter Gale (died at Andersonville), F. M. Richardson, Harvey Peters & Hank Prentiss; all of whom were prisoners with him in Andersonville. You are bidding on a fabulous group of letters detailing three years of hard fought a war and a scarce Andersonville pin that we have never encountered. CONDITION: Face of Andersonville pin is in good condition overall though rusted on back. Generally good as for Civil War letters. Paper is well-preserved with most documents having some light foxing at the margins or along fold marks. Two letters exhibit some chipping at the margins and light tears along fold lines. All are otherwise structurally sound. Ink and pencil are well preserved and completely legible. Ink is dark taking on a brown patina. Pencil on 2/63 letter is fading somewhat. Stationary ink retains good red and blue color with sharp battle scene details on the headers. 4-32632 JS16 (3,000-5,000)

TWO AUTOGRAPHS BY CONFEDERATE GENERAL J. E. B. STUART. This lot from an old stamp collection shows an envelope addressed to Mrs. J. E. B. Stuart in J. E. B. Stuart’s hand. There is an added, clipped autograph from letter placed on envelope to show that the other signature was an in situ autograph. Hinged above the address line is this clip. Envelope has 5¢ Jefferson Davis stamp from 1862 and a nice imprint, “Headquarters Cavalry Brigade / Army of the Potomac.” CONDITION: Attached, clipped autograph has been closely trimmed, removing portion of the “S” in Stuart. Hinge has stained paper. Envelope is soiled with numerous small tears and reductions. Stamp is partially missing, as can be seen in photograph. 4-31532 JS278 (4,000-5,000)

EARLY WOODEN SURVEYORS COMPASS S.THAXTER BOSTON. This early wooden surveyors compass probably dates to the 18th century and is made of walnut w/a brass engraved degree ring around the paper compass. The compass printed S.TH_XTER, MAKER, STATE STREET, BOSTON (There is a screw-hole after “H” where the “A” should be in Thaxter’s name. Compass ca. 1769). With make-do pine period carved cover. SIZE: 15″l. PROVENANCE: William Guthman Collection CONDITION: Missing parts and w/various screw holes. The paper compass stained. 4-32722 JJ18 (1,000-1,500)

1858 PATTERN BULLSEYE CANTEEN WITH SEVEN RINGS. 1858 pattern U.S. canteen with large remnant of the orig woolen cover showing rings which have been flattened. It is accompanied by one side of a petersham cover and used on such canteens when converted during the mid to late 1870’s. Included also are two canvas (duck) outer covers dating to the 1890’s. One cover is stenciled “U.S.”; the other is stenciled “U.S./37/BAND”. The latter probably dates to the Spanish-American War. CONDITION: Generally good. 4-32693 JL602 (350-750)

REGULATION CIVIL WAR BRASS AND COPPER BUGLE. This is an orig cavalry/infantry Civil War bugle made in the copper and brass construction with correct and orig markings on center of bugle bell just above the floating brass rim by well-known manufacturer “Stratton & Foote / New York”. Bugle has the added tone-adjusting “pig tail” twist between mouthpiece and bugle body. IT has the correct applied brass-over-copper reinforced floating rim and is correct full-length in size. Overall length is approx. 17-3/4” (including mouthpiece) with a 5-1/4” wide bell. John F. Stratton, on his own, held a number of Army contracts for instruments during the U. S. Civil War. Stratton & Foote were noted to have Federal U. S. Army contracts for “copper bugles” in Sept 1863 and Mar 1864. See the Stratton & Foote listing on p. 161 of A Directory of American Military Goods, Dealers, and Makers: 1785-1915 by Bazelon and McGuinn. This is a very nice Civil War bugle that would display well with any collection of cavalry items and carbines. CONDITION: Overall very good as cleaned with small scattered dents and scratches. 4-32928 JS254 (2,500-3,250)

ABRAHAM LINCOLN SIGNED APPOINTMENT TO BRIG GEN G.C. STRONG (KILLED AT FT. WAGNER). Large engraved presidential parchment document w/blue seal nominating George C. Strong as Brigadier General of Volunteers dated November 29, 1862. Full autographed signature of Abraham Lincoln and Edwin M. Stanton, Secretary of War. Also accompanying the lot is a carte de visite of General Strong done by J.E. Tilton, Boston, and a copy of U.S. Infantry Tactics, dated 1861 and signed by Strong, April 28, 1862. In 1863, Brig. General Strong was mortally wounded leading the ill-fated attack on Ft. Wagner, South Carolina. This attack, which included the 54th Massachusetts, was recently made even more famous by the movie “Glory”. Strong received a deathbed promotion to Major General as a result of his wounds at this battle. SIZE: 21-1/2″w x 26″h. CONDITION: Ink inscriptions legible and fold marks otherwise generally good . 4-31599 JJ7 (7,500-10,000)

IDENTIFIED PHOTO AND PAPER GROUPING FOR SERGEANT CHARLES COMBS, 1ST NEW YORK MOUNTED RIFLES. This group includes a very nice oval albumen photo, along with associated postwar certificates and paperwork, of Charles U. Combs (Combes) of Troop H, the 1st NY Mounted Rifles (NYMR). The 1st NYMR (sometimes designated as the 7th NY Cavalry) had service during the entire war from July 1861 to July 1865. The list of expeditions and engagements is too long and numerous to detail. Charles Combs enlisted as a Pvt in Troop H on Sept 13, 1862, in NY City. He served through the remainder of the war, mustering out in June 1865 at Richmond, VA. The oval albumen photo is sized at approximately 9” x 7”, being contained in a slightly larger period gold leaf frame. Frame has some damage to the leaf. View is a seated pose from the knees up. Pvt Combs is cradling his Light Cavalry sword in his arms, cross body with full sword belt and buckle displayed. The top of his cavalry boots can be seen. His unique bummers cap is seated on the table to his right and shows the rare insignia of cavalry cross sabers with a number “1” and “M” and “R” on either side. This is a very neat and unique view and this image is a in superior condition. Also included in the grouping are three postwar certificates dealing with Combs’ military service. The first is an “Army of the James” (23” x 27-1/2”) listing outlining Commanders, Corp Components, units, etc. The second is the typical war “Military Register” (21” x 26”) for Troop H, 1st NYMR, outlining the unit’s history and members. Cpl Combes is listed. The third item is a GAR certificate (23” x 19”) appointing Charles Combes as Aide de Camp, inked Detroit, April 1890. CONDITION: Overall very good as described above. 4-32930 JS258 (800-1,000)

Revised: 10/19/2007

(Additional Information) In a recent phone call from a prospective client it was asked if this was the exact same lot offered in our October 2005 Firearms Auction as Lot # 3485. Indeed this is the exact same lot in the same condition. The inquirer went on to ask if there was anything wrong with this lot? There is nothing wrong with this lot, it is exactly as we had offered it and sold it in 2005. At that time the lot realized far more than the current estimate. The winning bidder was Gary Zimet, whose address at the time was 5 Cardinal Dr., Washingtonville, NY 10992. Despite various attempts Mr. Zimet never settled his account (we have since been told that this was not the first occasion Mr. Zimet has done this). This is an outstanding historical lot, having come down directly from Commander Worden to his present day descendants.

MAGNIFICENT MILITARY PORTRAIT AND ORIG LINCOLN SIGNED CONGRESSIONAL RESOLUTION TO COMMANDER JOHN L. WORDEN OF THE USS MONITOR. Portrait is oil on board and is a copy of an identical portrait hanging in the US Naval Academy Museum in Annapolis, Maryland by Philipp Albert Gliemann (1822-1871). This portrait and genre painter was born in Germany in 1822-died in 1871. Gliemann was a student of the Academy of Art in Dresden and of the historical painter Julius Hubner. This portrait measures 19-3/4” x 24” (slightly smaller than the signed portrait in the Naval Academy Museum), and is unsigned but obviously from the hand of the same artist. Portrait of Worden is a half-length portrait in uniform with his head and eyes looking slightly up and left of the viewer. His dark hair is swept to the right and his sideburns run into a neatly combed full beard and mustache. He is depicted in US Navy, regulation uniform of dark blue with brightly highlighted, gold, full dress epaulets on each shoulder, bearing a sgl star. On his right sleeve is the regulation braid for a Rear Admiral, being two slightly raised bands on a broad band of gold embroidered lace with a five-pointed gold star above. Cuff of his white shirt is showing. Both of his hands hold the grip and knuckle bow of his elaborate, gold-plated, eagle pommel sword. Worden’s left pinky finger displays an oval garnet ring. Background is shades of gray, green, and black. Frame is of fancy gilded gesso and wood measuring 28” x 32”. Portrait is accompanied by Worden’s Congressional Resolution, which is a framed, partially printed document on vellum, measuring 15” x 18” and reads as follows: “Thirty-Seventh-Congress of the United States of America; At the-Third-Session, begun and held at the City of Washington, on Monday, the-First-day of December, one thousand eight hundred and sixty-two-A RESOLUTION Tendering the thanks of Congress to Commander John L. Worden of the United States Navy.-Resolved by the Senate and House of Representatives of the United States of America in Congress assembled, That in pursuance of the recommendation of the President of the United States, and to enable him to advance Commander John L. Worden one grade, in pursuance of the ninth section of the act of Congress of sixteenth July, eighteen hundred and sixty-two, that the thanks of Congress be, and they are hereby, tendered to the Commander John L. Worden, for highly distinguished conduct in conflict with the enemy, in the remarkable battle betwee(sic) the United States iron-clad steamer ‘Monitor,’ under his command, and the rebel iron-clad frigate ‘Merrimack,’ in March, eigh-ten (sic) hundred and sixty-two”. The document is signed by Schuyler Colfax, Speaker of the House of Representatives, Dan Clark, President Pro Tem of the Senate. At the bottom is signed in Abraham Lincoln’s own hand “Approved, February 3, 1863. Abraham Lincoln.” This portrait and this magnificent Presidential signed Congressional Resolution are related to the sgl most famous naval engagement of the American Civil War period. It began at dawn on March 1862, as CSS Virginia prepared for a renewed combat. Previous day, she had utterly defeated two big Federal warships, Congress and Cumberland, destroying both and killing moiré than 240 of their crewmen. This day, she expected to inflict a similar fate on the grounded steam frigate Minnesota and other enemy ships, probably freeing the lower Chesapeake Bay region of Union sea power and the land forces it supported. Innovative C.S.S. Virginia would thus contribute importantly to the Confederacy’s military, and perhaps diplomatic, fortunes. However, as they surveyed the opposite side of Hampton Roads, where the Minnesota and other potential victims awaited their fate, the Confederates realized that things were not going to be so simple. There, looking small and low near the lofty frigate, was a vessel- the USS Monitor, the U.S. Navy’s own ironclad, which had arrived the previous evening after a perilous voyage from New York. Though her crew was exhausted and their ship untested, the Monitor was also preparing for action. Undeterred, Virginia steamed out into Hampton Roads. Monitor positioned herself to protect the immobile Minnesota, and a general battle began. Both ships hammered away at each other with heavy cannon, and tried to run down and disable the other, but their iron-armored side prevented vital damage. Virginia’s smokestack was shot away, further reducing her already modest mobility, and Monitor’s technological troubles hindered the effectiveness of her two eleven-inch guns, the Navy’s most powerful weapons. Ammunition supply problems required her to temporarily pull away into shallower water, where the deep-drafted Virginia could not follow, but she always covered the Minnesota. Soon after noon, Virginia gunners concentrated their fire on Monitor’s pilothouse, a small iron blockhouse between bow and stern. A shell hit blinding Lieutenant John L. Worden, the Union ship’s Commanding Officer, forcing another withdrawal until he could be relieved. By the time she was ready to return to the fight, Virginia had turned away toward Norfolk. John Lorimer Worden was born on March 12, 1818 in the town of Mt. Pleasant, in Westchester County, NY. After his initial schooling, he became a U.S. Navy Midshipman in 1834 at the age of 16. He was promoted to the rank of Lieutenant in 1846 and he served in the store ship Southampton off California during the war with Mexico. As the secession crisis moved toward Civil War in early 1861, Lieutenant Worden was sent to Pensacola with secret instructions for the local naval Commander. While returning to Washington, D.C. by rail, he was arrested by Southern authorities and held as a prisoner of war for several months, an experience that badly damaged his health. He was eventually exchanged for a Lt. Sharpe of the Confederate Navy and returned to New York to recover his health in the care of his wife Olivia Toffey and her family for about seven months in the Quaker Hill area of Dutchess County. In February 1862, upon resuming active duty, he was given command of the revolutionary ironclad USS Monitor and took her into the historic battle with the CSS Virginia on March 9, 1862. Receiving serious eye injuries in the action, he had to relinquish command. Reportedly, Worden bore the powder marks from his facial wound for the rest of his life, as well as some loss of sight. However, this battle made him a major war hero in the North. While recovering, Worden was promoted to Commander in July of 1862. Further promoted to Captain, he commanded the Monitor-class Montauk during the first months of 1863, bombarding Fort McAllister, Georgia in January, destroying the Privateer Rattlesnake in February, and participating in the April 7, 1863 attack to recapture Fort Sumter. Captain Worden spent the remainder of the Civil War on the important duty of supervising the construction of new ironclads. He received the rank of Commodore in 1868 and the next year began five years as Superintendent of the U.S. naval Academy, during which time he was promoted to Rear Admiral. Rear Admiral John L. Worden died in Washington, D.C., on October 18, 1897. CONDITION: Framed oil painting is in very good condition, but unrestored. Scratches on Worden’s forehead and chipped paint loss on canvas near corners. Light paint flaking at the upper left hand corner and in the lower right hand corner. Painting has darkened with the age of its varnish. No defects affect the subject. Frame is in excellent condition with one broken scroll at the bottom. Partially printed Congressional Resolution is framed and in very good condition with some fading to the ink and signatures. 4-54211 JL20 (20,000-30,000)